scholarly journals DESIGNING ENVIRONMENTALLY HAZARDOUS OBJECTS BY MEANS OF GEOGRAPHIC INFORMATION SYSTEMS

2021 ◽  
Vol 1 (161) ◽  
pp. 134-140
Author(s):  
O. Pomortseva
Keyword(s):  
Information Systems ◽  
Geographic Information Systems ◽  
Solid Waste ◽  
3D Model ◽  
Three Dimensional ◽  
Geographic Information ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Waste Landfill ◽  
Triangulation Network

The article deals with the current problem of solid waste disposal. Also the use of geoinformation technologies in the design of environmentally hazardous facilities. The sequence of actions in case of reconstruction of a land plot for the construction of a solid waste landfill is described in detail. It shows how you can use geographic information systems to speed up and better accomplish the task. The convenience of using geographic information systems when planning such tasks is obvious. It is advisable to use geographic information systems when planning environmentally hazardous facilities. This is due to the complex nature of the problem. This requires the involvement of additional spatial data. It is the geographic information system that will allow the use of all data in the complex based on the principle of their spatial position. You can also use data models to support the creation, validation, and correction of information. In a geographic information system, you can create a geodatabase. This will create a 3D model of a solid waste landfill. The 3D model allows you to better represent the terrain. Creation of a triangulation network will allow to correlate all layers created in the geodatabase. The triangulation network is created from 3D terrain points. It allows you to get a three-dimensional model of a high-altitude polygon. This provides many possibilities in the future. It will be possible to interpret 3D models with high-precision engineering systems. This allows you to carry out any geometric measurements, build sections and profiles, as well as monitor activities at the solid waste landfill. Based on these data, it is possible to measure the volumes of household waste, areas, the height of the landfill in terms of the height of the actual relief and the level of groundwater, the altitude characteristics of the landfill and slopes to compare them with the standard indicators. The three-dimensional model will make it possible to identify inconsistencies between the actual boundaries of the polygon with the cadastral boundaries of the site allocated for these purposes. With the help of geographic information systems, simplicity, speed and clarity in the formation of conclusions and decision-making will be provided.

Data acquisition and analysis for highway construction using geographic information systems

2003 ◽  
Vol 30 (3) ◽  
pp. 533-542 ◽  
Author(s):  
Osama Moselhi ◽  
Ahmed Hassanein
Keyword(s):  
Information Systems ◽  
Geographic Information Systems ◽  
Data Acquisition ◽  
Construction Projects ◽  
Highway Construction ◽  
Three Dimensional ◽  
Data Entry ◽  
Geographic Information ◽  
Software Systems ◽  
Accurate Estimation

Earthmoving operations represent a sizeable percentage of highway construction costs. Accurate estimation of cut and fill quantities, as well as haul distances, are thus essential for developing realistic schedules and reliable cost estimates for highway construction projects. This paper presents a model designed to aid highway construction personnel in optimizing earthmoving operations by developing realistic mass haul diagrams. The model automates data acquisition and accounts for the presence of different soil strata and natural and (or) man-made obstructions affecting earthmoving plans. Geographic information systems (GIS) are employed to generate three-dimensional digital terrain models of the topography and soil profiles. The model is supported by a relational database for soil data and has been implemented in a prototype software developed in ArcView® environment. It provides a user-friendly interface to facilitate data entry and efficient reporting capabilities. The model has flexible input and output formats designed to facilitate data sharing with a number of commercially available software systems. A numerical example is presented to demonstrate the features of the developed model.Key words: data acquisition, geographic information systems, quantity estimating, earthwork optimization.

scholarly journals Influence of Geometric Features Associativity of CAD Class Models on the Process of Their Updating – Comparative Analysis

2021 ◽  
Author(s):  
Grzegorz Świaczny
Keyword(s):  
3D Model ◽  
Three Dimensional ◽  
Optimal Solution ◽  
3D Models ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Initial Design ◽  
The Individual ◽  
Class Models ◽  
Positive Effect

This article deals with the topic of one of the most important features of modern CAx class systems – associativity. The term refers to the ability to form relations (links) between two or more objects (in terms of their selected features), and with the consequence creating an associative (linked) three-dimensional model. The author pays special attention to the very process of creating relations between objects, as it has a key impact on the structural stability of CAD class models, and thus on their susceptibility to possible modifications. To show that not all associativity brings a positive effect, the author presents two examples of its implementation. In order to emphasize the influence of the method of linking individual elements, both examples are based on the same 3D model – a thin-walled part with a positioning pin. That means the geometric form of the default part is the same, whereas only relations of the individual objects of the 3D model change. In the first scenario, correctly defined relations between objects make that the positioning pin offset does not affect the initial design conditions. The second scenario shows an incorrect implementation of associativity, as a result of which the same operation of positioning pin offset gives non-compliance with the initial design conditions and with the consequence an undesirable change in its geometry. The article is an attempt to draw attention to the fact that the associative structure of 3D models is not always equal to the optimal solution. Only the well-thought-out nature of associativity allows to use all its advantages.

scholarly journals Modeling in AUTOCAD for bachelors

2021 ◽  
pp. 25-28
Author(s):  
Л.В. Карпюк ◽  
Н.О. Давіденко
Keyword(s):  
3D Model ◽  
Three Dimensional ◽  
Model Space ◽  
Educational Process ◽  
Point Of View ◽  
Two Dimensional ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Three Dimensional Objects ◽  
Graphic Editor

The article discusses the methods of using the AutoCad graphic editor for creating three-dimensional objects. The possibilities of three-dimensional modeling in the AutoCad graphic editor for optimizing the educational process of bachelors of technical specialties are also considered. The article analyzes the best ways to create mechanical engineering drawings.The most developed software tool for the production of design documentation is AutoCAD - a universal graphic design system. Creating models of any complexity in space by using this graphic editor, the user will be able to see their relative position, estimate the distance between them. The model can be freely moved in space, viewing many options. The ability to control the point of view allows to conveniently select the view of the 3D model that is being developed. Zooming, panning in real time with the ability to freely rotate the camera around the model provide the ability to quickly view objects from any point of view. The article provides examples of choosing the most optimal option for creating a three-dimensional model. The traditional way to create a 3D model drawing is to make 2D views of the model. When creating a flat drawing, there is a possibility of error when making projections, since they are created independently from each other and consist of several images. It is rather difficult to represent an object in space from a flat drawing. At present, modern software graphic editors are aimed at creating three-dimensional models that allow to create realistic models and, on their basis, get two-dimensional projections. Graphic editor AutoCad allows to create three-dimensional objects based on standard commands, in the form of a cylinder, cone, box, torus, etc., when editing which you can get the desired shapes. After creating a three-dimensional model, the user can get its two-dimensional projections not only on the main planes, but also on any plane at will. The 3D modeling method allows you to create a complex drawing with any number of images based on a 3D model. There are ways to create 2D plane drawings from a 3D model and the ability to edit ready-made designs that can be inserted from model space into paper space. Editing takes place by changing the parameters of a 3D object in model space, and these changes are automatically reflected in paper space. This method allows us to use the tools to quickly create a system of 3-4 linked views for a 3D AutoCad model.

scholarly journals Three-Dimensional Model Extraction and Parameter Measurement of Cerebral Hemangioma Based on Mimics

2022 ◽  
Vol 2160 (1) ◽  
pp. 012012
Author(s):  
An Qu ◽  
Tianmin Guan ◽  
Tianxiang Gan ◽  
Yuanyuan Li ◽  
Zhuang Lin ◽  
...  
Keyword(s):  
Therapeutic Effect ◽  
Cerebral Angiography ◽  
Structural Design ◽  
3D Model ◽  
Three Dimensional ◽  
The Body ◽  
Model Reconstruction ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
3D Model Reconstruction

Abstract In this paper, Mimics is using to reconstruct the 3D model of hemangioma from 2D cerebral angiography images. The process of 3D model reconstruction is formulated. The hemangioma model is extracted and the parameters of the hemangioma are measured, which provided a model basis for the structural design of the spring coil. The shape and structure of the coil are very important for the therapeutic effect. During the treatment, the coil is implanted into the hemangioma from outside the body through a catheter.

Integration of GIS and BIM in Metro Construction

2014 ◽  
Vol 608-609 ◽  
pp. 698-702 ◽  
Author(s):  
Qian Kun Wang ◽  
Peng Li ◽  
Ya Ping Xiao ◽  
Zhi Gang Liu
Keyword(s):  
Information Systems ◽  
Geographic Information Systems ◽  
Building Information Modeling ◽  
Three Dimensional ◽  
Geographic Information ◽  
Information Modeling ◽  
Modeling Technology ◽  
Effective Combination ◽  
Building Information ◽  
Three Dimensional Models

With application and popularization of information modeling technology, both Geographic Information Systems (GIS) and Building Information Modeling (BIM) could represent three dimensional models in different fields. By introducing application features of GIS and BIM in Metro construction, this paper presents such a thought that effective combination of GIS and BIM may play a role at different stages in metro construction.

Sign in / Sign up

Export Citation Format

Share Document