scholarly journals The Calculation of the Fuel Cost for a Car

2018 ◽  
Vol 47 (4) ◽  
pp. 277-282 ◽  
Author(s):  
Radik Ildarkhanov

The proposed formula derived considering the physical phenomena which occur during truck operation makes it possible to calculate fuel cost during the operation more accurately. The results of comparison of calculations by the proposed formula with test results tractors parties “TransEuroTest” are presented. The results of the calculation with the help of new formula differ from the experimentally obtained values of the fuel consumption of vehicles for not more than 1%. The average fuel consumption of tractors at an average speed is shown. The proposed formula for calculating the cost makes it easy to compare the fuel consumption of different vehicle options. The formula can also be used when evaluating the effect of vehicle weight on fuel consumption, which is impossible according to the well-known formulas.

1983 ◽  
Vol 105 (2) ◽  
pp. 75-87
Author(s):  
R. W. Radford

The cost of railway diesel fuel has become an increasingly high proportion of railway operating expenses. The paper analyzes the generation and utilization of rail horsepower in freight train operations. The effects on fuel consumption of variations in several parameters including train consist, car weight, gradient, average speed, meet strategy, throttle control, locomotive axle arrangement, and train marshalling are examined. Estimates are made of the value, in terms of fuel cost, of weight reduction of freight cars and of selective train marshalling.


1993 ◽  
Vol 30 (01) ◽  
pp. 39-50
Author(s):  
William L. Cave ◽  
Dominic S. Cusanelli

The effect of a stern flap on the powering performance and annual fuel consumption of an FFG-7 Oliver Hazard Perry Class Guided Missile Frigate is presented. Analytical analysis using free surface potential flow theory was conducted to evaluate the flow on the afterbody of the ship. Model tests were conducted to determine the optimum geometrical characteristics of the stern flap. Based on the analytical and model test results, a stern flap was retrofitted to an FFG-7 Class frigate, and full-scale results on powering performance were collected. Results of model powering experiments showed that the flap, set at 10 deg trailing edge down, decreased the delivered power by 8.4 percent at 26 knots, and provided for a 3.8 percent decrease in annual fuel consumption. This decrease in annual fuel consumption places the payback period on the cost of the flap installation at only 10 months. The full-scale comparison of the flap's effectiveness was marred by adverse weather conditions and differences in the pre-and post-flap ship configurations. However, observations of the full-scale stern wave system, before and after the installation of the stern flap, lead the authors to conclude that the flap will produce a larger decrease in delivered power at full scale than shown by the model experiments.


2009 ◽  
Vol 24 (3) ◽  
pp. 157-162 ◽  
Author(s):  
John Sessions ◽  
Jeff Wimer ◽  
Kevin Boston

Abstract The majority of log volume in the western United States is transported as long logs on stinger-steered pole trailers. Opportunities exist to increase value and reduce costs through hauling longer logs. Hauling longer logs often permits increasing gross vehicle weight, reducing the cost of transport and using less fuel per unit of log volume transported. Longer logs also increase the potential to recover value by retaining more bucking options at the mill. On higher-speed routes, hauling longer logs will decrease fuel consumption if vehicle air resistance is reduced. A number of issues associated with hauling longer logs must be considered, including truck performance on horizontal and vertical curves, gradeability, loading and unloading trucks, mill yard layout, method of log measurement, and bridge limits.


2021 ◽  
Vol 13 (8) ◽  
pp. 4528
Author(s):  
Olga Lingaitienė ◽  
Juozas Merkevičius ◽  
Vida Davidavičienė

The World Bank, United Nations, the Organization for Economic Cooperation and Development, and others are in line with the governments of countries that are strongly interested in the sustainable development of countries, regions, and enterprises. One of the aspects that affects the indicators and prospects of sustainable development is the efficiency of energy source use. Nationwide reductions in the greenhouse gas emissions of motor vehicles could have a direct effect on ambient temperature and reducing the effects of global warming, which can affect future environmental, societal, and economic development. Significant reductions in fuel consumption can be achieved by increasing the efficiency of use, and the performance, of current cargo vehicles. This aspect is directly related to cargo delivery systems and supply chain efficiency and effectiveness. The article solves the problem of increasing the effectiveness of cargo delivery and proposes a model that would minimize transportation costs that are directly related to fuel consumption, shortening transportation time. The model addresses the problem of a lack of models evaluating the efficiency of cargo to Lithuania that is using several different modes of transportation. For the solution to this problem, the article examines the complexity of the rational use of land and water vehicles depending on the type of cargo transported, the technical capabilities of the vehicles (loading, speed, environmental pollution, fuel consumption, etc.), and the type (cars, railways, ships). The novelty of the findings is based on the availability to select the most appropriate vehicles, on a case-by-case basis, from the available options, depending on their environmental performance and energy efficiency. This model, later in this article, is used for calculations of Lithuanian companies for selecting the most rational vehicle by identifying the most appropriate route, as well as assessing the dynamics of the economic and physical indicators. The model allows for creating dependencies between the main indicators characterizing the transport process—the cost, the time of transport, and the safety, taking into account the dynamics of economic and physical indicators, that lead to a very important issue—reducing the amount of energy required to provide products and services.


2021 ◽  
Vol 13 (14) ◽  
pp. 8066
Author(s):  
Thowayeb H. Hassan ◽  
Abu Elnasr E. Sobaih ◽  
Amany E. Salem

The cost of fuel and its availability are among the most major concerns for aircrafts and the aviation industry overall. Environmental difficulties with chemical pollutant emissions emitted by aviation machines are also connected to fuel consumption. As a result, it is crucial to examine factors that affect the overall fuel usage and consumption in the airport-based aviation industry. Several variables were investigated related to the total fuel consumed, such as dry operating weight (DOW) (KG), zero-fuel weight (ZFW), take-off weight (TOW), air distance (AIR DIST) (KM), and ground distance (GDN DIST). Analysis of the correlation between total fuel consumed as well as the extra fuel and selected variables was conducted. The results showed that the most positively associated factors with the total used fuel were the air distance (r2 = 0.86, p < 0.01), ground distance (r2 = 0.78, p < 0.01), TOW (r2 = 0.68, p < 0.01), and flight time (r2 = 0.68, p < 0.01). There was also a strong positive association between the average fuel flow (FF) and actual TOW (r2 = 0.74, p < 0.01) as well as ZFW (r2 = 0.61, p < 0.01). The generalized linear model (GLM) was utilized to assess the predictions of total energy usage after evaluating important outliers, stability of the homogeneity of variance, and the normalization of the parameter estimation. The results of multiple linear regression revealed that the most significant predictors of the total consumed fuel were the actual ZFW (p < 0.01), actual TOW (p < 0.01), and actual average FF (p < 0.05). The results interestingly confirmed that wind speed has some consequences and effects on arrival fuel usage. The result reflects that thermal and hydrodynamic economies impact on the flying fuel economy. The research has various implications for both scholars and practitioners of aviation industry.


Author(s):  
Leila Ladani ◽  
Lalit Roy

Additive Layer Fabrication, in particular Electron Beam Additive Fabrication (EBAF), has recently drawn much attention for its special usability to fabricate intricately designed parts as a whole. It not only increases the production rate which reduces the production lead time but also reduces the cost by minimizing the amount of waste material to a great extent. Ti6Al4V is the most common type of material that is currently being fabricated using EBAF technique. This material has been used in aerospace industry for several reasons such as excellent mechanical properties, low density, great resistance to corrosion, and non-magnetism. The effects of build direction of layers (namely, addition of layers along one of the x, y & z directions with respect to the build table) and the anisotropy effect caused by it has not been explored vigorously. This anisotropy effect has been investigated in this work. Different mechanical properties such as Yield Strength (YS), Ultimate Tensile Strength (UTS), and Modulus of Elasticity (E) of these three types of Ti6Al4V are determined using tensile tests and are compared with literature. The tensile test results show that YS and UTS for flat-build samples have distinguishably higher values than those of the side-build and top-build samples.


2014 ◽  
Vol 644-650 ◽  
pp. 381-384
Author(s):  
Xin Zhang ◽  
Hao Zhou ◽  
Guo Song Liu

In order to improve the efficiency of auto parts distribution logistics, to lower the cost of auto production in transportation logistics, and to reduce accidents, in this paper it is designed that an automatic guided vehicle control system to replace the manned tractors in the distribution sites. The system is equipped with an infrared homing device that can ensure the automated guided vehicle (AGV) along a predetermined route automatic driving at a given distribution information, without the needs to manually guided. Test results show that the circuit performance of AGV control system is stable to ensure the accuracy of the tracking in the practical application, and the mean absolute error of the tracking is less than 0.04m.


2016 ◽  
Vol 27 (01) ◽  
pp. 1650011 ◽  
Author(s):  
Tie-Qiao Tang ◽  
Qiang Yu

In this paper, we use car-following model to explore the influences of the vehicle’s fuel consumption and exhaust emissions on each commuter’s trip cost without late arrival on one open road. Our results illustrate that considering the vehicle’s fuel cost and emission cost only enhances each commuter’s trip cost and the system’s total cost, but has no prominent impacts on his optimal time headway at the origin of each open road under the minimum total cost.


2014 ◽  
Vol 875-877 ◽  
pp. 1454-1457
Author(s):  
Pan Hu ◽  
Yi He Zhang ◽  
Feng Shan Zhou ◽  
Yue Wang ◽  
Meng Fu ◽  
...  

A novel anti-caking material (E-Oil) was prepared from waste animal/plant oil and triethanolamine by catalytic synthesis in this study. The E-Oil was analyzed by FTIR and the anti-caking effect of anti-caking materials was described by caking ratio. The FTIR results showed that the reaction product of Waste Animal/Plant Oil and Hydramine was surfactant with anti-caking effect. The anti-caking test results indicated that E-Oil made the caking ratio of compound fertilizer decrease from 39.75% to 16.33%. Taking the cost into consideration, the optimal fraction of E Oil was 5‰ and the caking ratio could reach 16.33%, which could approximately meet the application requirements.


Author(s):  
Daniel E. Caguiat

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had a non-coated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and non-coated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the non-coated compressor. Overall test results show that it is feasible to utilize anti-fouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.


Sign in / Sign up

Export Citation Format

Share Document