scholarly journals Removal and Regeneration of Iron (III) from Water Using New Treated Fluorapatite Extracted from Natural Phosphate as Adsorbent

2021 ◽  
Vol 11 (5) ◽  
pp. 13130-13140
Keyword(s):  
Adsorption Capacity ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
Natural Phosphate ◽  
Dissolved Iron ◽  
Naturally Occurring ◽  
Ft Ir ◽  
Adsorption Desorption ◽  
Ft Ir Spectroscopy

Our study aims to evaluate the efficiency of dissolved iron (III) retention in synthetic solutions by adsorption on treated natural phosphate collected in the Khouribga region. This research focused on the valorization of phosphate, a naturally occurring resource that is abundant in Morocco. The resulting products were analyzed by various methods, including FT-IR spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM). In this work, we studied the effect of several parameters such as adsorbent amount, contact time, solution pH, and initial concentration of iron (III) on the adsorption process. The results of the adsorption of iron (III) indicate that the efficiency was achieved after 5 minutes, and the maximum adsorption capacity calculated from the Langmuir model was 26.18 mg g-1. The regeneration and reuse of synthesized adsorbent are effective for five cycles of adsorption-desorption cycles without reducing adsorption capacity.

scholarly journals Silica-Coated Magnetic Nanocomposites for Pb2+ Removal from Aqueous Solution

2020 ◽  
Vol 10 (8) ◽  
pp. 2726 ◽  
Author(s):  
Roxana Nicola ◽  
Otilia Costişor ◽  
Mihaela Ciopec ◽  
Adina Negrea ◽  
Radu Lazău ◽  
...  
Keyword(s):  
Iron Oxide ◽  
Adsorption Capacity ◽  
Aqueous Media ◽  
Physical Stability ◽  
Absorption Capacity ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Similar Materials ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Magnetic iron oxide-silica shell nanocomposites with different iron oxide/silica ratio were synthesized and structurally characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), small-angle neutron scattering, magnetic and N2-sorption studies. The composite that resulted with the best properties in terms of contact surface area and saturation of magnetization was selected for Pb2+ adsorption studies from aqueous media. The material presented good absorption capacity (maximum adsorption capacity 14.9 mg·g−1) comparable with similar materials presented in literature. Its chemico-physical stability and adsorption capacity recommend the nanocomposite as a cheap adsorbent material for lead.

scholarly journals Removal of Phosphorus from Wastewater by Different Morphological Alumina

Molecules ◽  
2020 ◽  
Vol 25 (13) ◽  
pp. 3092
Author(s):  
Jianchuan Sun ◽  
Awang Gao ◽  
Xuhui Wang ◽  
Xiangyu Xu ◽  
Jiaqing Song
Keyword(s):  
Adsorption Capacity ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Phosphorus Adsorption ◽  
X Ray ◽  
Transmission Electron ◽  
Ft Ir ◽  
Series Of Experiments ◽  
Level 1 ◽  
Adsorption Desorption

In this work, an organic-free method was used to synthesize different morphological boehmite by controlling the crystallization temperature, and alumina adsorbents were obtained by baking the boehmites at 500 °C. The alumina adsorbents were characterized by X-ray diffraction (XRD), High resolution transmission electron microscope (HRTEM), Fourier transform infrared (FT-IR), N2 adsorption/desorption analysis, and their phosphorus adsorption properties were comparatively investigated by a series of experiments. The results showed that the self-prepared alumina adsorbents were lamellar and fibrous material, while the industrial adsorbent was a granular material. The lamellar alumina adsorbents had the largest specific surface area and showed better phosphorus adsorption capacity. The maximum adsorption capacity could reach up to 588.2 mg·g−1; and only 0.8 g·L−1 of lamellar alumina adsorbent is needed to treat 100 mg·L−1 phosphorus solution under the Chinese level 1 discharge standard (0.5 mg·L−1). Further investigation suggests that the lamellar alumina adsorbent kept high adsorption capacity in various solution environments.

scholarly journals Removal of Chromium(III) and Cadmium(II) Heavy Metal Ions from Aqueous Solutions Using Treated Date Seeds: An Eco-Friendly Method

Molecules ◽  
2021 ◽  
Vol 26 (12) ◽  
pp. 3718
Author(s):  
Mohammad Azam ◽  
Saikh Mohammad Wabaidur ◽  
Mohammad Rizwan Khan ◽  
Saud I. Al-Resayes ◽  
Mohammad Shahidul Islam
Keyword(s):  
Metal Ions ◽  
Adsorption Capacity ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Surface Analysis Techniques ◽  
Adsorption Processes ◽  
Ft Ir ◽  
Metal Elution ◽  
Date Pits

The aim of the research was to prepare low-cost adsorbents, including raw date pits and chemically treated date pits, and to apply these materials to investigate the adsorption behavior of Cr(III) and Cd(II) ions from wastewater. The prepared materials were characterized using SEM, FT-IR and BET surface analysis techniques for investigating the surface morphology, particle size, pore size and surface functionalities of the materials. A series of adsorption processes was conducted in a batch system and optimized by investigating various parameters such as solution pH, contact time, initial metal concentrations and adsorbent dosage. The optimum pH for achieving maximum adsorption capacity was found to be approximately 7.8. The determination of metal ions was conducted using atomic adsorption spectrometry. The experimental results were fitted using isotherm Langmuir and Freundlich equations, and maximum monolayer adsorption capacities for Cr(III) and Cd(II) at 323 K were 1428.5 and 1302.0 mg/g (treated majdool date pits adsorbent) and 1228.5 and 1182.0 mg/g (treated sagai date pits adsorbent), respectively. It was found that the adsorption capacity of H2O2-treated date pits was higher than that of untreated DP. Recovery studies showed maximal metal elution with 0.1 M HCl for all the adsorbents. An 83.3–88.2% and 81.8–86.8% drop in Cr(III) and Cd(II) adsorption, respectively, were found after the five regeneration cycles. The results showed that the Langmuir model gave slightly better results than the Freundlich model for the untreated and treated date pits. Hence, the results demonstrated that the prepared materials could be a low-cost and eco-friendly choice for the remediation of Cr(III) and Cd(II) contaminants from an aqueous solution.

Selective Removal of Hg2+ Ions from Water Using New Functionalized Silica Resin: Equilibrium, Thermodynamics and Kinetic Modeling Studies

2021 ◽  
Vol 43 (4) ◽  
pp. 436-436
Author(s):  
Nida Shams Jalbani Nida Shams Jalbani ◽  
Amber R Solangi Amber R Solangi ◽  
Shahabuddin Memon Shahabuddin Memon ◽  
Ranjhan Junejo Ranjhan Junejo ◽  
Asif Ali Bhatti Asif Ali Bhatti
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Mechanism ◽  
Solid Phase ◽  
Maximum Adsorption Capacity ◽  
Adsorption Phenomenon ◽  
Column Adsorption ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Wastewater Samples ◽  
Ft Ir Spectroscopy

In current study, the diphenylaminomethylcalix[4]arene (3) was synthesized and immobilized onto silica surface to prepare a selective, regenerable and stable resin-4. The synthesized resin-4 has been characterized by FT-IR spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy (EDX) and Brunauer-Emmett-Teller (BET) techniques. To check the adsorption capacity of resin-4, the batch and column adsorption methodology were applied and it has observed that the resin-4 was selectively removed Hg2+ ions under the optimized parameters. The maximum adsorption capacity was obtained at pH 9 using 25 mg/L of resin-4. Under the optimal conditions, different equilibrium, kinetic and thermodynamic models were applied to experimental data. The results show that adsorption mechanism is chemical in nature following Langmuir model with good correlation coefficient (R2=0.999) and having 712.098 (mmol/g) adsorption capacity. The energy of calculated from D-R model suggests the ion exchange nature of the adsorption phenomenon. Dynamic adsorption experiments were conducted using Thomas model. The maximum solid phase concentration (qo) was 7.5 and rate constant was found to be 0.176 with (R2=0.938) for Hg2+ ions. The kinetic study describes that the adsorption mechanism follows pseudo second order (R2=0.999). The thermodynamic parameters such as ∆H (0.032 KJ/mol) and ∆S (0.127 KJ/mol /K) and ∆G (-5.747,-6.306, -7.027 KJ/mol) shows that the adsorption of Hg2+ ion is endothermic and spontaneous. The reusability of resin-4 was also checked and it has observed that the after 15 cycle only 1.2 % adsorption reduces. Moreover, the resin-4 was applied on real wastewater samples obtained from local industrial zone of Karachi, Sindh-Pakistan.

scholarly journals Preparation of GO/MIL-101(Fe,Cu) composite and its adsorption mechanisms for phosphate in aqueous solution

2021 ◽  
Author(s):  
You Wu ◽  
Zuannian Liu ◽  
Bakhtari Mohammad Fahim ◽  
Junnan Luo
Keyword(s):  
Adsorption Capacity ◽  
Photoelectron Spectroscopy ◽  
Adsorption Mechanism ◽  
Nitrogen Adsorption ◽  
Adsorption Properties ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Adsorption Mechanisms ◽  
Adsorption Desorption

Abstract In this study, MIL-101(Fe), MIL-101(Fe,Cu), and Graphene Oxide (GO) /MIL-101(Fe,Cu) were synthesized to compose a novel sorbent. The adsorption properties of these three MOFs-based composites were compared toward the removal of phosphate. Furthermore, the influencing factors including reaction time, pH, temperature and initial concentration on the adsorption capacity of phosphate on these materials as well as the reusability of the material were discussed. The structure of fabricated materials and the removal mechanism of phosphate on the composite material were analyzed by Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), nitrogen adsorption-desorption analysis and zeta potential. The results show that the maximum adsorption capacity of phosphate by the composite GO/MIL-101(Fe,Cu)-2% was 204.60 mg·g− 1, which is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe). likewise the specific surface area of GO/MIL-101(Fe,Cu)-2% is 778.11 m2/g is higher than that of MIL-101(Fe,Cu) and MIL-101(Fe),which are 747.75 and 510.66m2/g respectively. The adsorption mechanism of phosphate is electrostatic attraction, form coordination bonds and hydrogen bonds. The fabricated material is a promising adsorbent for the removal of phosphate with good reusability.

The synthesis, characterization and catalytic application of manganese porphyrins bonded to novel modified SBA-15

2018 ◽  
Vol 42 (8) ◽  
pp. 6464-6471 ◽  
Author(s):  
Saeed Rayati ◽  
Parinaz Nafarieh ◽  
Mostafa M. Amini
Keyword(s):  
Nitrogen Adsorption ◽  
Ordered Mesoporous Silica ◽  
X Ray Diffraction ◽  
Manganese Porphyrins ◽  
Catalytic Application ◽  
Silica Material ◽  
Ordered Mesoporous ◽  
Ft Ir ◽  
Adsorption Desorption ◽  
Ft Ir Spectroscopy

In the presented research, a highly ordered mesoporous silica material (SBA-15) was functionalized with imidazole as a functionalizing reagent (SBA-TMSIm) and then characterized via FT-IR spectroscopy, thermogravimetric analysis (TGA), powder X-ray diffraction (XRD) and nitrogen adsorption/desorption isotherms.

Improved Study on the Performance of Polyacrylamide/Attapulgite Clay Composite Material Removing Copper (II) Ions from Aqueous Solution

2014 ◽  
Vol 609-610 ◽  
pp. 26-31
Author(s):  
Chun Lei Li ◽  
Hui Xu ◽  
Jun Long Zhang ◽  
Wei Wang ◽  
Jing Tang ◽  
...  
Keyword(s):  
Metal Ion ◽  
Ion Concentration ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Freundlich Isotherms ◽  
Thermodynamics And Kinetics ◽  
Equilibrium Data ◽  
Ft Ir ◽  
Adsorption Desorption ◽  
Ft Ir Spectroscopy

A removal of Cu (II) ions from aqueous solutions onto PAM/ATP has been investigated using batch adsorption technique, including the effect of pH, contact time, initial metal ion concentration, adsorption thermodynamics and kinetics. PAM/ATP was characterized with Fourier transform infrared (FT-IR) spectroscopy and scanning electron microscopy (SEM). The equilibrium data were analyzed using Langmuir and Freundlich isotherms and the best interpretation was given by Langmuir. The maximum adsorption capacity was found to be 212 mg/g after 60 min when pH =3. Regeneration experiments showed that the investigated PAM/ATP could be reused without significant adsorption losses even after five adsorption-desorption cycles.

scholarly journals Synthesis and Characterization of CuFe2O4 Nanoparticles Modified with Polythiophene: Applications to Mercuric Ions Removal

Nanomaterials ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 586 ◽  
Author(s):  
Ayman H. Kamel ◽  
Amr A. Hassan ◽  
Abd El-Galil E. Amr ◽  
Hadeel H. El-Shalakany ◽  
Mohamed A. Al-Omar
Keyword(s):  
Electron Microscopy ◽  
Aqueous Solution ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
X Ray ◽  
Transmission Electron ◽  
Enhanced Adsorption ◽  
Co Precipitation ◽  
Adsorption Desorption

In this research, CuFe2O4 nanoparticles were synthesized by co-precipitation methods and modified by coating with thiophene for removal of Hg(II) ions from aqueous solution. CuFe2O4 nanoparticles, with and without thiophene, were characterized by x-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), energy dispersive x-ray (EDX), high-resolution transmission electron microscopy (HRTEM) and Brunauer–Emmett–Teller (BET). Contact time, adsorbent dose, solution pH, adsorption kinetics, adsorption isotherm and recyclability were studied. The maximum adsorption capacity towards Hg2+ ions was 7.53 and 208.77 mg/g for CuFe2O4 and CuFe2O4@Polythiophene composite, respectively. Modification of CuFe2O4 nanoparticles with thiophene revealed an enhanced adsorption towards Hg2+ removal more than CuFe2O4 nanoparticles. The promising adsorption performance of Hg2+ ions by CuFe2O4@Polythiophene composite generates from soft acid–soft base strong interaction between sulfur group of thiophene and Hg(II) ions. Furthermore, CuFe2O4@Polythiophene composite has both high stability and reusability due to its removal efficiency, has no significant decrease after five adsorption–desorption cycles and can be easily removed from aqueous solution by external magnetic field after adsorption experiments took place. Therefore, CuFe2O4@Polythiophene composite is applicable for removal Hg(II) ions from aqueous solution and may be suitable for removal other heavy metals.

Adsorption Characteristic of U(VI) on Fe-Immobilized Bentonite

2013 ◽  
Vol 639-640 ◽  
pp. 1300-1306
Author(s):  
Zhen Ping Tang ◽  
Hui Ling ◽  
Shui Bo Xie ◽  
S.Y. Li ◽  
J.S. Wang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Adsorption Mechanism ◽  
Ph Value ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
X Ray Diffraction ◽  
Solution Ph ◽  
Adsorption Characteristic ◽  
Order Kinetic Equation

Fe-immobilized bentonite, prepared with bentonite and FeCl3 was used for the adsorption of uranium(VI) in this study, solution pH, ion strength, contact time and temperature were investigated, structural characterization of Fe-immobilized bentonite was assayed by X-ray Diffraction and Fourier Transform Infrared Spectroscopy. Results indicated that the adsorption capacity were strongly affected by the solution pH and ion strength, the adsorption efficiency was 91.8% when pH value was 6 and ion strength was 0.01 mol•L-1, higher or lower pH did not favor the U(VI) adsorption. The adsorption mechanism was discussed by the views of reactive kinetics and thermodynamics along with Scanning Electron Microscope. The adsorption kinetics process was fitted well with the second-order kinetic equation, when the initial U(VI) concentration was less than 38.08mg/L, Langmuir equations could describe the adsorption isotherm of U(VI) well with the maximum adsorption capacity of 169.5mg/g at 303K

A functionalized tannin-chitosan bentonite composite with superior adsorption capacity for Cr(VI)

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Zhongmin Li ◽  
Peng Zou ◽  
Junzhou Yang ◽  
Miaoyang Huang ◽  
Linye Zhang ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Raw Materials ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Initial Ph ◽  
System Part ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Xrd Patterns

AbstractA novel functionalized tannin-chitosan bentonite composite (TCBC) was successfully synthesized. The formation of the composite was confirmed by the X-ray diffraction (XRD) patterns and Fourier transform infrared spectroscopy (FT-IR) analysis. The pHpzc of TCBC was 3.38. The influences such as pH, dosage of TCBC, temperature and initial Cr(VI) concentration on adsorption capacity were investigated. The experimental data indicated that the almost saturated adsorption of the TCBC towards Cr(VI) in 100 min. The maximum adsorption capacity was 262.08 mg/g at 333 K with initial pH = 2.5. The adsorption kinetics of Cr(VI) on TCBC followed the pseudo-second-order kinetics model. The isothermal data were well described by the models of Langmuir, Freundlich and Temkin. The results revealed that the adsorption of Cr(VI) on TCBC existed comprehensive effects and mainly belong to the chemisorption. The TCBC could keep good performances (qe = 192.17 mg/g) in five runs, 1 M NaOH was used as eluent for desorption, which showed a high desorption efficiency. Studies showed TCBC prepared with low cost and green raw materials, and simple green preparation technology had high adsorption capacity, good reusability and acidic tolerance. By exploring the Cr(VI)-Cr(III) hybrid system, part of Cr(VI) was reduced to Cr(III) and adsorbed by TCBC. The optimal adsorption pH of Cr(III) was 5.0.

Sign in / Sign up

Export Citation Format

Share Document