scholarly journals Characterization of Electrodeposited Cadmium Selenide Thin Films

2012 ◽  
Vol 60 (1) ◽  
pp. 137-140 ◽  
Author(s):  
RI Chowdhury ◽  
MS Islam ◽  
F Sabeth ◽  
G Mustafa ◽  
SFU Farhad ◽  
...  
Keyword(s):  
Thin Films ◽  
Cadmium Selenide ◽  
Low Cost ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Cdse Film ◽  
Cell Structures ◽  
Deposited Film ◽  
Deposited Films

Cadmium selenide (CdSe) thin films have been deposited on glass/conducting glass substrates using low-cost electrodeposition method. X-ray diffraction (XRD) technique has been used to identify the phases present in the deposited films and observed that the deposited films are mainly consisting of CdSe phases. The photoelectrochemical (PEC) cell measurements indicate that the CdSe films are n-type in electrical conduction, and optical absorption measurements show that the bandgap for as-deposited film is estimated to be 2.1 eV. Upon heat treatment at 723 K for 30 min in air the band gap of CdSe film is decreased to 1.8 eV. The surface morphology of the deposited films has been characterized using scanning electron microscopy (SEM) and observed that very homogeneous and uniform CdSe film is grown onto FTO/glass substrate. The aim of this work is to use n-type CdSe window materials in CdTe based solar cell structures. The results will be presented in this paper in the light of observed data.DOI: http://dx.doi.org/10.3329/dujs.v60i1.10352  Dhaka Univ. J. Sci. 60(1): 137-140 2012 (January)

InSe Nanothin Film with Ar-Gas Low Vacuum Pressure

2014 ◽  
Vol 606 ◽  
pp. 15-18
Author(s):  
Falah I. Mustafa ◽  
Mooroj Ali
Keyword(s):  
Thin Films ◽  
Diffraction Analysis ◽  
Room Temperature ◽  
Energy Gap ◽  
X Ray Diffraction ◽  
Argon Gas ◽  
X Ray ◽  
Glass Substrates ◽  
Deposited Film ◽  
Deposited Films

InxSe1-x(x = 0.4, 0.5, 0.6) thin films are deposited at room temperature on glass substrates with thickness ~500nm by thermal evaporation technique. The X-Ray diffraction analysis showed that both the as-deposited films In2Se3and InSe (x= 0.4 and 0.5) are amorphous in nature while the as-deposited film In3Se2is polycrystalline and the values of energy gap are Eg=1.44eV for In2Se3, Eg=1.16eV for InSe and Eg=0.78eV for In3Se2. The same technique used with insert Argon gas at pressure 0.1 mbar where InxSe1-x(x = 0.4, 0.5, 0.6) thin films are deposited at room temperature on glass substrates with thickness ~100nm. The X-Ray diffraction analysis showed that the as-deposited films In2Se3are amorphous in nature while the as-deposited film InSe and In3Se2are Nanocrystalline with grain size 33nm and 55nm respectively and the values of energy gap are Eg=1.55eV for InSe and Eg=1.28eV for In3Se2. The energy gap of InSe thin films increase with Argon gas assist and phases changes from amorphous and polycrystalline to nanostructure material by thermal vacuum deposition technique.

Chemical synthesis and study of structural and optoelectronic properties of CdS thin films: Effect of SILAR growth cycles

2015 ◽  
Vol 9 (3) ◽  
pp. 2461-2469
Author(s):  
S. R. Gosavi ◽  
K. B. Chaudhari
Keyword(s):  
Thin Films ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
Silar Method ◽  
Growth Cycles ◽  
Glass Substrates ◽  
Layer Adsorption ◽  
Cds Thin Films ◽  
Structural And Optoelectronic Properties ◽  
Deposited Film

CdS thin films were deposited on glass substrates by using successive ionic layer adsorption and reaction (SILAR) method at room temperature. The effect of SILAR growth cycles on structural, morphological, optical and electrical properties of the films has been studied.  The thickness of the deposited film is measured by employing weight difference method. The X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) studies showed that all the films exhibit polycrystalline nature and are covered well with glass substrates. The values of average crystallite size were found to be 53 nm, 58 nm, 63 nm and 71 nm corresponding to the thin films deposited with 30, 40, 50 and 60 SILAR growth cycles respectively. From the UV–VIS spectra of the deposited thin films, it was seen that both the absorption properties and energy bandgap of the films changes with increasing number of SILAR growth cycles. A decrease of electrical resistivity has been observed with increasing SILAR growth cycle. 

Thermal conversion of CBD grown ZnS thin films to ZnO

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Kooliyankal Naseema ◽  
Kaniyamkandy Ribin ◽  
Nidiyanga Navya ◽  
Prasoon Prasannan
Keyword(s):  
Thin Films ◽  
Low Cost ◽  
Thermal Conversion ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
Glass Substrates ◽  
Anion Substitution ◽  
Nano Crystalline ◽  
Before And After ◽  
Uv Visible

AbstractNano crystalline zinc sulfide thin films were deposited onto glass substrates by chemical bath deposition method. One of the samples was annealed at 300 °C for 2 h in air using a muffle furnace. The prepared thin films were investigated by X-ray diffraction (XRD), UV–visible spectroscopy (UV–vis), photoluminescence spectroscopy (PL), scanning electron microscopy (SEM) and Raman spectroscopy (FT-R) studies before and after annealing. The analysis confirmed the thermal-induced anion substitution and conversion of ZnS crystal to ZnO wurtzite crystal. XRD pattern showed that these films were phase pure and polycrystalline in nature. Optical band gap was found to be 3.86 eV for ZnS and 3.21 eV for ZnO. The films prepared by this simple, low-cost technique are suitable for photovoltaic and optoelectronic applications.

LUMINESCENT PROPERTIES OF SOL-GEL DEPOSITED Eu:TiO2 THIN FILMS

2001 ◽  
Vol 15 (17n19) ◽  
pp. 769-773 ◽  
Author(s):  
M. GARCIA-ROCHA ◽  
A. CONDE-GALLARDO ◽  
I. HERNANDEZ-CALDERON ◽  
R. PALOMINO-MERINO
Keyword(s):  
Thin Films ◽  
Sol Gel ◽  
Luminescent Properties ◽  
X Ray Diffraction ◽  
Si Substrates ◽  
Glass Substrates ◽  
Corning Glass ◽  
Different Temperatures ◽  
Hecd Laser

In this work we show the results on tile growth and optical characterization of TiO 2 thin films doped with Eu atoms. Eu:TiO2 films were grown at room temperature with different Eu concentrations by sol-gel on Si Corning glass substrates. A different crystalline structure is developed for the films deposited on Corning glass than those deposited on Si as observed from x-ray diffraction experiments. Room and low temperature photoluminescence (PL) was measured by using two different lines (325 and 442 nm) of a HeCd laser. A strong PL signal associated to the 5 D 0→7 F 2 transition from Eu +3 was observed. A better emission was obtained from those films deposited on Si substrates, Finally, the evolution of the PL signal is studied when the samples are annealed at different temperatures in O 2 atmosphere.

Electrochemical Deposition and Characterization of Cd-Fe-Se Thin Films

2009 ◽  
Vol 68 ◽  
pp. 69-76 ◽  
Author(s):  
S. Thanikaikarasan ◽  
T. Mahalingam ◽  
K. Sundaram ◽  
Tae Kyu Kim ◽  
Yong Deak Kim ◽  
...  
Keyword(s):  
Thin Films ◽  
Hexagonal Structure ◽  
X Rays ◽  
X Ray Diffraction ◽  
X Ray ◽  
Iron Selenide ◽  
Glass Substrates ◽  
Diffraction Patterns ◽  
Cadmium Iron Selenide ◽  
Deposited Films

Cadmium iron selenide (Cd-Fe-Se) thin films were deposited onto tin oxide (SnO2) coated conducting glass substrates from an aqueous electrolytic bath containing CdSO4, FeSO4 and SeO2 by potentiostatic electrodeposition. The deposition potentials of Cadmium (Cd), Iron (Fe), Selenium (Se) and Cadmium-Iron-Selenide (Cd-Fe-Se) were determined from linear cathodic polarization curves. The deposited films were characterized by x-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive analysis by x-rays (EDX) and optical absorption techniques, respectively. X-ray diffraction patterns shows that the deposited films are found to be hexagonal structure with preferential orientation along (100) plane. The effect of FeSO4 concentration on structural, morphological, compositional and optical properties of the films are studied and discussed in detail.

Growth of Copper Telluride Thin Films using Electrodeposition

2018 ◽  
Vol 21 (1) ◽  
pp. 015-019
Author(s):  
P. Jeyakumar ◽  
S. Thanikaikarasan ◽  
B. Natarajan ◽  
T. Mahalingam ◽  
Luis Ixtlilco
Keyword(s):  
Thin Films ◽  
X Ray Diffraction ◽  
Electrodeposition Technique ◽  
Cyclic Voltammetric ◽  
Voltammetric Analysis ◽  
Copper Telluride ◽  
X Ray ◽  
Microstructural Parameters ◽  
Glass Substrates ◽  
Deposited Films

Copper Telluride thin films have been prepared on Fluorine doped Tin Oxide coated conducting glass substrates using electrodeposition technique. Cyclic voltammetric analysis has been carried out to analyze the growth mechanism of the deposited films. Thickness value of the deposited films has been estimated using Stylus profilometry. X-ray diffraction pattern revealed that the prepared films possess polycrystalline in nature. Microstructural parameters such as crystallite size, strain and dislocation density are evaluated using observed X-ray diffraction data. Optical absorption analysis showed that the prepared films are found to exhibit band gap value around 2.03 eV.

Thermoelectric Characterization of Direct Current Magnetron Co-Sputtering Zinc Antimonide Thin Films

2013 ◽  
Vol 734-737 ◽  
pp. 2559-2562
Author(s):  
Ying Zhen Li ◽  
Ping Fan ◽  
Zhuang Hao Zheng ◽  
Peng Juan Liu ◽  
Qing Yun Lin ◽  
...  
Keyword(s):  
Thin Films ◽  
Direct Current ◽  
Annealing Temperature ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Zinc Antimonide ◽  
Β Phase ◽  
Bk7 Glass ◽  
Diffraction Peaks

Direct current magnetron co-sputtering was used to deposit zinc antimonide thin films on BK7 glass substrates at room-temperature. Then the films were annealed at 573 K to 673 K for 1 hour in Ar atmosphere. The results indicate that the Seebeck coefficient of the thin films increase from 30.5 μVK-1to 132.5 μVK-1 when the annealing temperature changed. The electrical conductivity of the thin films increases from 3.45×103 to 6.86×103 Sm-1 and the Power Factor is enhanced greatly from 0.03×10-4 to 0.99×10-4 Wm-1K-2 when the annealing temperature reached 598 K. X-ray diffraction result shows that the major diffraction peaks of the thin films match those of β phase Zn4Sb3 and high crystalline thin films are achieved after annealing.

Effects of Annealing on Pulsed Laser Deposited TiO2 Thin Films

2013 ◽  
Vol 446-447 ◽  
pp. 306-311 ◽  
Author(s):  
Sudhanshu Dwivedi ◽  
Somnath Biswas
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Si Substrates ◽  
Morphological Studies ◽  
Atomic Force ◽  
Deposited Films ◽  
Type Crystal

Mixed phase TiO2 thin films of rutile and anatase type crystal orientations were deposited on Si substrates by pulsed laser deposition (PLD) technique. When annealed at 800°C at 1 mbar oxygen pressure for 3 h, the deposited films transform into a single phase of rutile type. Structural and morphological studies of the as-deposited and annealed films were performed with X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), Raman spectroscopy, and atomic force microscopy (AFM). Photoluminescence (PL) spectroscopy was used for optical characterization of the annealed thin films.

Characterization of MnS Thin Films Deposited by Chemical Bath Deposition

2019 ◽  
Vol 969 ◽  
pp. 433-438 ◽  
Author(s):  
Dattatraya K. Sonavane ◽  
S.K. Jare ◽  
M.A. Shaikh ◽  
R.V. Kathare ◽  
R.N. Bulakhe
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Band Gap Energy ◽  
Sulfur Source ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Double Beam

Glass substrates are used to deposit thin films utilizing basic and value effective chemical bath deposition (CBD) technique. The films were prepared from the mixture as solutions of manganous acetate tetrahydrate [C4H6MnO44H2O] as a manganese source, thiourea [(H2 N) 2 CS] as a sulfur source and triethanolamine (TEA) [(HOC2H4)3N] as a complexing agent.In the present paper the deposition was successfully done at 60 °C temperature. The absorption properties and band gap energy were determined employing double beam spectrophotometer. The optical band gap value calculated from absorption spectra of MnS thin film is found to be about 3.1eV.The MnS thin film was structurally characterized by X-ray Diffraction (XRD). The MnS thin film was morphologically characterized by Scanning Electron Microscopy (SEM) and elemental analysis was performed using EDS to confirm the formation of MnS.

Preparation and Characterization of Cu2ZnSnSe4 Thin Films by Selenization of Electrodeposited Metal Precursors

2011 ◽  
Vol 685 ◽  
pp. 105-109 ◽  
Author(s):  
Ji Li ◽  
Zhong Wei Zhang ◽  
Yang Ou ◽  
Wei Feng Liu ◽  
Guo Shun Jiang ◽  
...  
Keyword(s):  
Thin Films ◽  
Energy Dispersive Spectrometry ◽  
Saturated Calomel Electrode ◽  
Elemental Selenium ◽  
X Ray Diffraction ◽  
Glass Substrates ◽  
Metal Precursors ◽  
Different Temperatures ◽  
Electrodeposited Metal

Cu2ZnSnSe4thin films were prepared by selenization of electrodeposited Cu-Zn-Sn precursors. The Cu-Zn-Sn precursors were electrodeposited on the Mo-coated glass substrates from an electrolyte containing copper sulfate, zinc sulfate, tin (II) sulfate at a fixed potential between -1.2V and -1.25V vs. saturated calomel electrode, then the Cu2ZnSnSe4thin films were obtained by selenizing Cu-Zn-Sn precursors in elemental selenium atmosphere at different temperatures. The structure, composition and optical properties of the films were investigated by X-ray diffraction, Energy dispersive spectrometry and UV-VIS absorption spectroscopy. The CZTSe films have a stannite structure and an optical band-gap about 1.6 eV which is suitable for fabricating solar cells.

Sign in / Sign up

Export Citation Format

Share Document