scholarly journals Optimization of Abs 3D-Printing Method and Parameters

1970 ◽  
Vol 3 (1) ◽  
pp. 44-51
Author(s):  
Paweł Żur ◽  
Alicja Kołodziej ◽  
Andrzej Baier ◽  
Grzegorz Kokot
Keyword(s):  
3D Printing ◽  
Tensile Test ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Electric Car ◽  
University Of Technology ◽  
Static Tensile ◽  
3D Printed ◽  
Printing Method

The paper presents research on the method of 3D-printing ABS (Acrylonitrile butadiene styrene). Series of specimens were 3D-printed in FDM (Fused Deposition Modelling) technology with variable parameters. The influence of the following parameters has been checked: temperature of printing and infill density. Moreover, the material properties of raw, unprocessed ABS have been inspected. The tensile strength of specimens and Young’s modulus have been determined in a static tensile test. Tests were carried out in compliance with the ASTM D638-14 standard. Obtained results were then compared with the material datasheet. Optimum printing method has been defined. The carried out research resulted in optimizing the printing method for ABS vehicle parts applied in Silesian Greenpower electric car. The car has been developed by students of The Silesian University of Technology in Gliwice, Poland as an interfaculty students’ project. Results of the tensile test research have been analysed and discussed and conclusions have been presented in the following article.

Investigations on 3D printed thermosetting and ceramic-reinforced recycled thermoplastic-based functional prototypes

2019 ◽  
pp. 089270571986462 ◽  
Author(s):  
Rupinder Singh ◽  
Ranvijay Kumar ◽  
Inderpreet Singh
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Surface Hardness ◽  
Acrylonitrile Butadiene Styrene ◽  
Experimental Investigations ◽  
Fused Deposition Modelling ◽  
Ceramic Particles ◽  
Fused Deposition ◽  
Thermoplastic Matrix ◽  
3D Printed

The 3D printing of thermoplastic polymers (both virgin and reinforced with metal/ceramic particles) has been widely explored in recent past with fused deposition modelling (FDM) process. But hitherto very little has been reported on 3D printing of thermoplastics polymers with reinforcement of thermosetting polymers and ceramic particles. This article is an extension of work reported on thermo-mechanical investigations on waste thermosetting polymer bakelite and ceramic (silicon carbide and aluminium oxide) as reinforcement in recycled acrylonitrile butadiene styrene (ABS) thermoplastic matrix for sustainability. The study reports the experimental investigations on mechanical (tensile), morphological, surface hardness and thermal stability analysis of 3D printed functional prototype as tensile specimen (as per ASTM D 638). In the present case study, it has been ascertained that composition/proportion of thermoplastic matrix has a significant role in controlling the mechanical properties, whereas other input process parameters of FDM are insignificant. The results of the study suggest that thermosetting and ceramic-reinforced ABS thermoplastic-based 3D printed parts have mechanical properties at par with unreinforced ABS.

scholarly journals 3D Printing of Thermo-Sensitive Drugs

Pharmaceutics ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1524
Author(s):  
Sadikalmahdi Abdella ◽  
Souha H. Youssef ◽  
Franklin Afinjuomo ◽  
Yunmei Song ◽  
Paris Fouladian ◽  
...  
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Fused Deposition Modelling ◽  
Future Directions ◽  
Digital Light Processing ◽  
Fused Deposition ◽  
Printing Technique ◽  
3D Printed ◽  
Semi Solid ◽  
Selection Of

Three-dimensional (3D) printing is among the rapidly evolving technologies with applications in many sectors. The pharmaceutical industry is no exception, and the approval of the first 3D-printed tablet (Spiratam®) marked a revolution in the field. Several studies reported the fabrication of different dosage forms using a range of 3D printing techniques. Thermosensitive drugs compose a considerable segment of available medications in the market requiring strict temperature control during processing to ensure their efficacy and safety. Heating involved in some of the 3D printing technologies raises concerns regarding the feasibility of the techniques for printing thermolabile drugs. Studies reported that semi-solid extrusion (SSE) is the commonly used printing technique to fabricate thermosensitive drugs. Digital light processing (DLP), binder jetting (BJ), and stereolithography (SLA) can also be used for the fabrication of thermosensitive drugs as they do not involve heating elements. Nonetheless, degradation of some drugs by light source used in the techniques was reported. Interestingly, fused deposition modelling (FDM) coupled with filling techniques offered protection against thermal degradation. Concepts such as selection of low melting point polymers, adjustment of printing parameters, and coupling of more than one printing technique were exploited in printing thermosensitive drugs. This systematic review presents challenges, 3DP procedures, and future directions of 3D printing of thermo-sensitive formulations.

Use of polymer concrete for large-scale 3D printing

2021 ◽  
Vol 27 (3) ◽  
pp. 465-474
Author(s):  
Martin Krčma ◽  
David Škaroupka ◽  
Petr Vosynek ◽  
Tomáš Zikmund ◽  
Jozef Kaiser ◽  
...  
Keyword(s):  
3D Printing ◽  
Large Scale ◽  
Mechanical Performance ◽  
Construction Material ◽  
Polymer Concrete ◽  
Fused Deposition Modelling ◽  
Cast State ◽  
Content Type ◽  
Fused Deposition ◽  
3D Printed

Purpose This paper aims to focus on the evaluation of a polymer concrete as a three-dimensional (3D) printing material. An associated company has developed plastic concrete made from reused unrecyclable plastic waste. Its intended use is as a construction material. Design/methodology/approach The concrete mix, called PolyBet, composed of polypropylene and glass sand, is printed by the fused deposition modelling process. The process of material and parameter selection is described. The mechanical properties of the filled material were compared to its cast state. Samples were made from castings and two different orientations of 3D-printed parts. Three-point flex tests were carried out, and the area of the break was examined. Computed tomography of the samples was carried out. Findings The influence of the 3D printing process on the material was evaluated. The mechanical performance of the longitudinal samples was close to the cast state. There was a difference in the failure mode between the states, with cast parts exhibiting a tougher behaviour, with fractures propagating in a stair-like manner. The 3D-printed samples exhibited high degrees of porosity. Originality/value The results suggest that the novel material is a good fit for 3D printing, with little to no degradation caused by the process. Layer adhesion was shown to be excellent, with negligible effect on the finished part for the longitudinal orientation. That means, if large-scale testing of buildability is successful, the material is a good fit for additive manufacturing of building components and other large-scale structures.

Mechanical Properties of Diamond Schwarzites: From Atomistic Models to 3D-Printed Structures

MRS Advances ◽  
2020 ◽  
Vol 5 (33-34) ◽  
pp. 1775-1781 ◽  
Author(s):  
Levi C. Felix ◽  
Vladimir Gaál ◽  
Cristiano F. Woellner ◽  
Varlei Rodrigues ◽  
Douglas S. Galvao
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Uniaxial Compression ◽  
Chemical Vapour ◽  
Md Simulations ◽  
Atomic Model ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Structural Applications ◽  
3D Printed

ABSTRACTTriply Periodic Minimal Surfaces (TPMS) possess locally minimized surface area under the constraint of periodic boundary conditions. Different families of surfaces were obtained with different topologies satisfying such conditions. Examples of such families include Primitive (P), Gyroid (G) and Diamond (D) surfaces. From a purely mathematical subject, TPMS have been recently found in materials science as optimal geometries for structural applications. Proposed by Mackay and Terrones in 1991, schwarzites are 3D crystalline porous carbon nanocrystals exhibiting a TPMS-like surface topology. Although their complex topology poses serious limitations on their synthesis with conventional nanoscale fabrication methods, such as Chemical Vapour Deposition (CVD), schwarzites can be fabricated by Additive Manufacturing (AM) techniques, such as 3D Printing. In this work, we used an optimized atomic model of a schwarzite structure from the D family (D8bal) to generate a surface mesh that was subsequently used for 3D-printing through Fused Deposition Modelling (FDM). This D schwarzite was 3D-printed with thermoplastic PolyLactic Acid (PLA) polymer filaments. Mechanical properties under uniaxial compression were investigated for both the atomic model and the 3D-printed one. Fully atomistic Molecular Dynamics (MD) simulations were also carried out to investigate the uniaxial compression behavior of the D8bal atomic model. Mechanical testings were performed on the 3D-printed schwarzite where the deformation mechanisms were found to be similar to those observed in MD simulations. These results are suggestive of a scale-independent mechanical behavior that is dominated by structural topology.

scholarly journals Tribology behaviour investigation of 3D printed polymers

2019 ◽  
Vol 10 (2) ◽  
pp. 173-181
Author(s):  
Muammel M. Hanon ◽  
Márk Kovács ◽  
László Zsidai
Keyword(s):  
Acrylonitrile Butadiene Styrene ◽  
Poly Lactic Acid ◽  
Fused Deposition Modelling ◽  
Tribological Behaviour ◽  
Fused Deposition ◽  
Motion System ◽  
Friction Factors ◽  
The Coefficient Of Friction ◽  
3D Printed ◽  
The Difference

3D printing of Acrylonitrile Butadiene Styrene (ABS) and Poly Lactic Acid (PLA) were used to prepare specimens utilising fused deposition modelling (FDM) technology. Two colours of PLA filament were printed; white and grey, whereas ABS only in white colour. Determining the tribological properties of 3D printed samples have been carried out, through obtaining the frictional features of different 3D printable filaments. Alternating-motion system employed for measuring the tribological factors. Studying the difference between static and dynamic friction factors and the examination of wear values were included. A comparison among the tribological behaviour of the 3D printed polymers has been investigated. The printed white ABS and PLA specimens show insignificant differences in the results tendency. On the contrary, the grey PLA exhibits a considerable variation due to the incredible growth in the coefficient of friction and wear average as well.

Anisotropy Evaluation of Different Raster Directions, Spatial Orientations, and Fill Percentage of 3D Printed PETG Tensile Test Specimens

2019 ◽  
Vol 821 ◽  
pp. 167-173 ◽  
Author(s):  
Muammel M. Hanon ◽  
Róbert Marczis ◽  
László Zsidai
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Tensile Test ◽  
Fused Deposition Modelling ◽  
Elongation At Break ◽  
Know How ◽  
Fused Deposition ◽  
Test Pieces ◽  
3D Printed ◽  
Fill Percentage

In this paper, the mechanical properties of Polyethylene terephthalate-glycol (PETG) tensile test specimens have been investigated. The test pieces were prepared using fused deposition modelling (FDM) 3D printing technology. Three print settings were examined which are: raster direction angles, print orientations, and infill percentage and patterns in order to evaluate the anisotropy of objects when employing FDM print method. The variations in stress-strain curves, tensile strength values and elongation at break among the tested samples were studied and compared. Illustration for the broken specimens after the tensile test was accomplished to know how the test pieces printed with various parameters were fractured. A comparison with some previous results regarding the elongation at break has been carried out.

scholarly journals Ten guidelines for the design of non-assembly mechanisms: The case of 3D-printed prosthetic hands

2018 ◽  
Vol 232 (9) ◽  
pp. 962-971 ◽  
Author(s):  
Juan Sebastian Cuellar ◽  
Gerwin Smit ◽  
Amir A Zadpoor ◽  
Paul Breedveld
Keyword(s):  
Developing Countries ◽  
3D Printing ◽  
Fused Deposition Modelling ◽  
Prosthetic Hand ◽  
Prosthetic Devices ◽  
Hand Prosthesis ◽  
Fused Deposition ◽  
Prosthetic Hands ◽  
Design Considerations ◽  
3D Printed

In developing countries, prosthetic workshops are limited, difficult to reach, or even non-existent. Especially, fabrication of active, multi-articulated, and personalized hand prosthetic devices is often seen as a time-consuming and demanding process. An active prosthetic hand made through the fused deposition modelling technology and fully assembled right after the end of the 3D printing process will increase accessibility of prosthetic devices by reducing or bypassing the current manufacturing and post-processing steps. In this study, an approach for producing active hand prosthesis that could be fabricated fully assembled by fused deposition modelling technology is developed. By presenting a successful case of non-assembly 3D printing, this article defines a list of design considerations that should be followed in order to achieve fully functional non-assembly devices. Ten design considerations for additive manufacturing of non-assembly mechanisms have been proposed and a design case has been successfully addressed resulting in a fully functional prosthetic hand. The hand prosthesis can be 3D printed with an inexpensive fused deposition modelling machine and is capable of performing different types of grasping. The activation force required to start a pinch grasp, the energy required for closing, and the overall mass are significantly lower than body-powered commercial prosthetic hands. The results suggest that this non-assembly design may be a good alternative for amputees in developing countries.

scholarly journals Three-dimensional Printing Versus Conventional Machining in the Creation of a Meatal Urethral Dilator: a Cost and Mechanical Strength Analysis

2020 ◽  
Author(s):  
Michael Yue-Cheng Chen ◽  
Jacob Skewes ◽  
Ryan Daley ◽  
Maria Ann Woodruff ◽  
Nicholas John Rukin
Keyword(s):  
3D Printing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Strength Analysis ◽  
Fused Deposition Modelling ◽  
3D Printer ◽  
Current Time ◽  
Fused Deposition ◽  
3D Printed ◽  
Conventional Machining

Abstract BackgroundThree-dimensional (3D) printing is a promising technology but the limitations are often poorly understood. We compare different 3D printingmethods with conventional machining techniques in manufacturing meatal urethral dilators which were recently removed from the Australian market. MethodsA prototype dilator was 3D printed vertically orientated on a low cost fused deposition modelling (FDM) 3D printer in polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS). It was also 3D printed horizontally orientated in ABS on a high-end FDM 3D printer with soluble support material, as well as on a SLS 3D printer in medical nylon. The dilator was also machined in stainless steel using a lathe. All dilators were tested mechanically in a custom rig by hanging calibrated weights from the handle until the dilator snapped. ResultsThe horizontally printed ABS dilator experienced failure at a greater load than the vertically printed PLA and ABS dilators respectively (503g vs 283g vs 163g, p < 0.001). The SLS nylon dilator and machined steel dilator did not fail. The steel dilator is most expensive with a quantity of five at 98 USD each, but this decreases to 30 USD each for a quantity of 1000. In contrast, the cost for the SLS dilator is 33 USD each for five and 27 USD each for 1000. ConclusionsAt the current time 3D printing is not a replacement for conventional manufacturing. 3D printing is best used for patient-specific parts, prototyping or manufacturing complex parts that have additional functionality that cannot otherwise beachieved.

scholarly journals Modelling and Investigation of Crack Growth for 3D-Printed Acrylonitrile Butadiene Styrene (ABS) with Various Printing Parameters and Ambient Temperatures

Polymers ◽  
2021 ◽  
Vol 13 (21) ◽  
pp. 3737
Author(s):  
Yousef Lafi A. Alshammari ◽  
Feiyang He ◽  
Muhammad A. Khan
Keyword(s):  
3D Printing ◽  
Crack Growth ◽  
Three Dimensional ◽  
Acrylonitrile Butadiene Styrene ◽  
Fused Deposition Modelling ◽  
Structural Dynamic ◽  
Fused Deposition ◽  
Nozzle Size ◽  
Printing Parameters ◽  
Butadiene Styrene

Three-dimensional (3D) printing is one of the significant industrial manufacturing methods in the modern era. Many materials are used for 3D printing; however, as the most used material in fused deposition modelling (FDM) technology, acrylonitrile butadiene styrene (ABS) offers good mechanical properties. It is perfect for making structures for industrial applications in complex environments. Three-dimensional printing parameters, including building orientation, layers thickness, and nozzle size, critically affect the crack growth in FDM structures under complex loads. Therefore, this paper used the dynamic bending vibration test to investigate their influence on fatigue crack growth (FCG) rate under dynamic loads and the Paris power law constant C and m. The paper proposed an analytical solution to determine the stress intensity factor (SIF) at the crack tip based on the measurement of structural dynamic response. The experimental results show that the lower ambient temperature, as well as increased nozzle size and layer thickness, provide a lower FCG rate. The printing orientation, which is the same as loading, also slows the crack growth. The linear regression between these parameters and Paris Law’s coefficient also proves the same conclusion.

Sign in / Sign up

Export Citation Format

Share Document