scholarly journals Development of a Bioprocess for the Production of Cyclic Lipopeptides Pseudofactins With Efficient Purification From Collected Foam

2020 ◽  
Vol 8 ◽  
Author(s):  
Piotr Biniarz ◽  
Marius Henkel ◽  
Rudolf Hausmann ◽  
Marcin Łukaszewicz
Keyword(s):  
High Performance ◽  
Single Step ◽  
High Yield ◽  
Efficient Production ◽  
Cyclic Lipopeptides ◽  
Enhanced Production ◽  
Working Volume ◽  
New Process ◽  
Co Precipitation ◽  
Surface Active Compounds

Microbial surfactants (biosurfactants) have gained interest as promising substitutes of synthetic surface-active compounds. However, their production and purification are still challenging, with significant room for efficiency and costs optimization. In this work, we introduce a method for the enhanced production and purification of cyclic lipopeptides pseudofactins (PFs) from Pseudomonas fluorescens BD5 cultures. The method is directly applicable in a technical scale with the possibility of further upscaling. Comparing to the original protocol for production of PFs (cultures in mineral salt medium in shaken flasks followed by solvent-solvent extraction of PFs), our process offers not only ∼24-fold increased productivity, but also easier and more efficient purification. The new process combines high yield of PFs (∼7.2 grams of PFs per 30 L of working volume), with recovery levels of 80–90% and purity of raw PFs up to 60–70%. These were achieved with an innovative, single-step thermal co-precipitation and extraction of PFs directly from collected foam, as a large amount of PF-enriched foam was produced during the bioprocess. Besides we present a protocol for the selective production of PF structural analogs and their separation with high-performance liquid chromatography. Our approach can be potentially utilized in the efficient production and purification of other lipopeptides of Pseudomonas and Bacillus origin.

scholarly journals Direct roll transfer printed silicon nanoribbon arrays based high-performance flexible electronics

2021 ◽  
Vol 5 (1) ◽  
Author(s):  
Ayoub Zumeit ◽  
Abhishek Singh Dahiya ◽  
Adamos Christou ◽  
Dhayalan Shakthivel ◽  
Ravinder Dahiya
Keyword(s):  
Flexible Electronics ◽  
High Performance ◽  
Printed Electronics ◽  
Field Effect Transistors ◽  
High Mobility ◽  
Single Step ◽  
High Yield ◽  
Transfer Printing ◽  
Large Area ◽  
Direct Printing

AbstractTransfer printing of high mobility inorganic nanostructures, using an elastomeric transfer stamp, is a potential route for high-performance printed electronics. Using this method to transfer nanostructures with high yield, uniformity and excellent registration over large area remain a challenge. Herein, we present the ‘direct roll transfer’ as a single-step process, i.e., without using any elastomeric stamp, to print nanoribbons (NRs) on different substrates with excellent registration (retaining spacing, orientation, etc.) and transfer yield (∼95%). The silicon NR based field-effect transistors printed using direct roll transfer consistently show high performance i.e., high on-state current (Ion) >1 mA, high mobility (μeff) >600 cm2/Vs, high on/off ratio (Ion/off) of around 106, and low hysteresis (<0.4 V). The developed versatile and transformative method can also print nanostructures based on other materials such as GaAs and thus could pave the way for direct printing of high-performance electronics on large-area flexible substrates.

scholarly journals Effects of the 20-Kilodalton Helper Protein on Cry1Ac Production and Spore Formation in Bacillus thuringiensis

2001 ◽  
Vol 67 (12) ◽  
pp. 5362-5369 ◽  
Author(s):  
Zongze Shao ◽  
Ziduo Liu ◽  
Ziniu Yu
Keyword(s):  
Bacillus Thuringiensis ◽  
Recombinant Strain ◽  
Protein Production ◽  
Heliothis Armigera ◽  
High Yield ◽  
Efficient Production ◽  
Crystal Proteins ◽  
Enhanced Production ◽  
Molecular Chaperon

ABSTRACT Bacillus thuringiensis produces large amounts of various pesticidal proteins during the stationary phase. In order to achieve a high yield and form crystals, some pesticidal proteins require the presence of other proteins. Helper protein P20 is required for efficient production of both the Cyt1A and Cry11A crystal proteins in B. thuringiensis subsp. israelensis. Although full-length Cry1 protoxins are usually independent in terms of expression and crystallization in B. thuringiensis, in this study P20 significantly enhanced production of Cry1Ac protoxin (133 kDa) in an acrystalliferous and plasmid-negative strain. In the presence of P20, the yield of Cry1Ac protoxin increased 2.5-fold, and on average the resulting crystals were 1.85 μm long and 0.85 μm wide, three times the size of the crystals formed in the control lacking P20. Correspondingly, the recombinant strain that coexpressed P20 and Cry1Ac exhibited higher toxicity against Heliothis armigera larvae than the control. Furthermore, serious degradation of Cry1Ac in vivo was observed, which has seldom been reported previously. Actually, most protein was completely degraded during synthesis, and after synthesis about one-third of the expressed protoxins were degraded further before crystallization. In this process, P20 protected only nascent Cry1Ac from degradation, indicating that it acted as a molecular chaperon. In addition, spores were smaller and rounder and had a thinner exosporium layer when they were produced in the presence of P20. In summary, Cry1Ac was severely degraded during synthesis; this degradation was effectively relieved by P20, which resulted in enhanced production. Our results indicated that P20 is an effective tool for optimizing protein production in vivo.

Purification of Urokinase from Complex Mixtures Using Immobilized Monoclonal Antibody Against Urokinase Light Chain

1983 ◽  
Vol 49 (01) ◽  
pp. 024-027 ◽  
Author(s):  
David Vetterlein ◽  
Gary J Calton
Keyword(s):  
Monoclonal Antibody ◽  
Light Chain ◽  
Culture Media ◽  
Biological Fluids ◽  
Single Step ◽  
High Yield ◽  
Step Method ◽  
Commercial Preparation ◽  
E Coli ◽  
Tissue Culture Media

SummaryThe preparation of a monoclonal antibody (MAB) against high molecular weight (HMW) urokinase light chain (20,000 Mr) is described. This MAB was immobilized and the resulting immunosorbent was used to isolate urokinase starting with an impure commercial preparation, fresh urine, spent tissue culture media, or E. coli broth without preliminary dialysis or concentration steps. Monospecific antibodies appear to provide a rapid single step method of purifying urokinase, in high yield, from a variety of biological fluids.

scholarly journals Iodine reduction for reproducible and high-performance perovskite solar cells and modules

2021 ◽  
Vol 7 (10) ◽  
pp. eabe8130
Author(s):  
Shangshang Chen ◽  
Xun Xiao ◽  
Hangyu Gu ◽  
Jinsong Huang
Keyword(s):  
Solar Cells ◽  
High Performance ◽  
High Efficiency ◽  
Electronic Materials ◽  
Substantial Reduction ◽  
Perovskite Solar Cells ◽  
High Yield ◽  
Operation Conditions ◽  
Record Value ◽  
Precursor Powders

Perovskite-based electronic materials and devices such as perovskite solar cells (PSCs) have notoriously bad reproducibility, which greatly impedes both fundamental understanding of their intrinsic properties and real-world applications. Here, we report that organic iodide perovskite precursors can be oxidized to I2 even for carefully sealed precursor powders or solutions, which markedly deteriorates the performance and reproducibility of PSCs. Adding benzylhydrazine hydrochloride (BHC) as a reductant into degraded precursor solutions can effectively reduce the detrimental I2 back to I−, accompanied by a substantial reduction of I3−-induced charge traps in the films. BHC residuals in perovskite films further stabilize the PSCs under operation conditions. BHC improves the stabilized efficiency of the blade-coated p-i-n structure PSCs to a record value of 23.2% (22.62 ± 0.40% certified by National Renewable Energy Laboratory), and the high-efficiency devices have a very high yield. A stabilized aperture efficiency of 18.2% is also achieved on a 35.8-cm2 mini-module.

scholarly journals Graphene/silver-based composites and coating on dead coral for degradation of organic pollution using the Z-scheme mechanism

RSC Advances ◽  
2021 ◽  
Vol 11 (32) ◽  
pp. 19890-19901
Author(s):  
Maedeh Nooriha Najafabadi ◽  
Hajar Ghanbari ◽  
Rahim Naghizadeh
Keyword(s):  
High Performance ◽  
Organic Pollution ◽  
Dead Coral ◽  
Silver Phosphate ◽  
Co Precipitation ◽  
Hydrothermal Methods

A high-performance photocatalytic nanocomposite consisting of silver phosphate-based particles with GO and RGO was synthesized by co-precipitation and hydrothermal methods.

scholarly journals Self-Powered All-Inorganic Perovskite Photodetectors with Fast Response Speed

2021 ◽  
Vol 16 (1) ◽  
Author(s):  
Ting Zhang ◽  
Shibin Li
Keyword(s):  
High Performance ◽  
Solution Process ◽  
Response Speed ◽  
Fast Response ◽  
Single Step ◽  
Inorganic Perovskite ◽  
Perovskite Materials ◽  
Photoactive Materials ◽  
Self Powered ◽  
Solvent Processing

AbstractIn this manuscript, the inorganic perovskite CsPbI2Br and CsPbIBr2 are investigated as photoactive materials that offer higher stability than the organometal trihalide perovskite materials. The fabrication methods allow anti-solvent processing the CsPbIxBr3−x films, overcoming the poor film quality that always occur in a single-step solution process. The introduced diethyl ether in spin-coating process is demonstrated to be successful, and the effects of the anti-solvent on film quality are studied. The devices fabricated using the methods achieve high-performance, self-powered and the stabilized photodetectors show fast response speed. The results illustrate a great potential of all-inorganic CsPbIxBr3−x perovskites in visible photodetection and provide an effective way to achieve high performance devices with self-powered capability.

scholarly journals Additive-Enhanced Exfoliation for High-Yield 2D Materials Production

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 601
Author(s):  
Dinh-Tuan Nguyen ◽  
Hsiang-An Ting ◽  
Yen-Hsun Su ◽  
Mario Hofmann ◽  
Ya-Ping Hsieh
Keyword(s):  
Large Scale ◽  
2D Materials ◽  
Transition Metal Dichalcogenides ◽  
Spectroscopic Characterization ◽  
High Yield ◽  
Nanometer Scale ◽  
Efficient Production ◽  
Device Performance ◽  
Metal Dichalcogenides ◽  
Scale Deposition

The success of van-der-Waals electronics, which combine large-scale-deposition capabilities with high device performance, relies on the efficient production of suitable 2D materials. Shear exfoliation of 2D materials’ flakes from bulk sources can generate 2D materials with low amounts of defects, but the production yield has been limited below industry requirements. Here, we introduce additive-assisted exfoliation (AAE) as an approach to significantly increase the efficiency of shear exfoliation and produce an exfoliation yield of 30%. By introducing micrometer-sized particles that do not exfoliate, the gap between rotor and stator was dynamically reduced to increase the achievable shear rate. This enhancement was applied to WS2 and MoS2 production, which represent two of the most promising 2D transition-metal dichalcogenides. Spectroscopic characterization and cascade centrifugation reveal a consistent and significant increase in 2D material concentrations across all thickness ranges. Thus, the produced WS2 films exhibit high thickness uniformity in the nanometer-scale and can open up new routes for 2D materials production towards future applications.

scholarly journals Computational and experimental investigations of one-step conversion of poly(carbonate)s into value-added poly(aryl ether sulfone)s

2016 ◽  
Vol 113 (28) ◽  
pp. 7722-7726 ◽  
Author(s):  
Gavin O. Jones ◽  
Alexander Yuen ◽  
Rudy J. Wojtecki ◽  
James L. Hedrick ◽  
Jeannette M. García
Keyword(s):  
High Performance ◽  
Density Functional ◽  
Value Added ◽  
Single Step ◽  
Nucleophilic Attack ◽  
Experimental Investigations ◽  
Aryl Ether ◽  
One Step ◽  
Poly Carbonate

It is estimated that ∼2.7 million tons poly(carbonate)s (PCs) are produced annually worldwide. In 2008, retailers pulled products from store shelves after reports of bisphenol A (BPA) leaching from baby bottles, reusable drink bottles, and other retail products. Since PCs are not typically recycled, a need for the repurposing of the PC waste has arisen. We report the one-step synthesis of poly(aryl ether sulfone)s (PSUs) from the depolymerization of PCs and in situ polycondensation with bis(aryl fluorides) in the presence of carbonate salts. PSUs are high-performance engineering thermoplastics that are commonly used for reverse osmosis and water purification membranes, medical equipment, as well as high temperature applications. PSUs generated through this cascade approach were isolated in high purity and yield with the expected thermal properties and represent a procedure for direct conversion of one class of polymer to another in a single step. Computational investigations performed with density functional theory predict that the carbonate salt plays two important catalytic roles in this reaction: it decomposes the PCs by nucleophilic attack, and in the subsequent polyether formation process, it promotes the reaction of phenolate dimers formed in situ with the aryl fluorides present. We envision repurposing poly(BPA carbonate) for the production of value-added polymers.

scholarly journals High-yield production of a super-soluble miniature spidroin for biomimetic high-performance materials

2021 ◽  
Author(s):  
Benjamin Schmuck ◽  
Gabriele Greco ◽  
Andreas Barth ◽  
Nicola M. Pugno ◽  
Jan Johansson ◽  
...  
Keyword(s):  
High Performance ◽  
High Yield ◽  
Yield Production ◽  
High Yield Production
Sign in / Sign up

Export Citation Format

Share Document