scholarly journals Eco-Friendly Procedure for Rendering the Antibacterial and Antioxidant of Cotton Fabrics via Phyto-Synthesized AgNPs With Malva sylvestris (MS) Natural Colorant

Author(s):  
Mousa Sadeghi-Kiakhani ◽  
Ali Reza Tehrani-Bagha ◽  
Fateme Sadat Miri ◽  
Elaheh Hashemi ◽  
Mahdi Safi

There is a growing interest for producing multifunctional cellulose fabrics using green and sustainable technology. In this study, we explored an eco-friendly procedure for dyeing cotton fabrics with Malva sylvestris (MS) as a natural colorant and rendering antibacterial cotton fabric by the silver nanoparticles. MS colorants were extracted from dried petals in water using the ultrasound technique, cotton fabrics were dyed with the extracted MS colorant at 100°C for 90 min. The colorimetric data and colorfastness properties were investigated in the absence and presence of tannic acid (TA) as a bio-mordant. Results indicated that MS dye had a high potential for reducing the silver nitrate, so that the silver particle size distribution on cotton fabric was obtained 50–80 nm, and TA had a positive effect on the MS extract and reduced Ag on the cotton. Furthermore, the reduction of bacterial growth of the dyed cotton considerably (up to 99%) improved by AgNPs. The wash-, and light-fastness properties of samples dyed with MS were enhanced from moderate to good-very good by mordanting.

2017 ◽  
Vol 46 (3) ◽  
pp. 210-217 ◽  
Author(s):  
Hatem E. Gaffer ◽  
Mohamed R. Elgohary ◽  
Hassan Ali Etman ◽  
Saad Shaaban

Purpose The purpose of this paper was to synthesize novel antibacterial reactive dyes for dyeing cotton fabrics. Design/methodology/approach Four synthetic novel antibacterial reactive dyes based on sulfonamide (D1-D4) have been synthesized by the coupling reaction of sulfonamide diazonium salt with sulfonamido-cyanurated 7-amino-4-hydroxynaphthalene-2-sulfonic acid “j-acid”. The chemical structure of the synthesized dyes was secured by their spectral data [infra red (IR) and proton Nuclear magnetic Resonance (1HNMR)]. Findings The prepared reactive dyes (D1-D4) were applied to cotton fabrics. Optimum conditions of the dying samples at sodium sulfate 100 g/l, liquor ratio (L.R.) 1:10, sodium carbonate 20 g/l at 80°C (D1, D2 and D4), 60°C (D3 for 60 min) were investigated. The fastness properties toward washing, perspiration, rubbing and light were evaluated. Dyed fabrics showed good light fastness property and good to very good washing and perspiration fastness properties according to the gray scale. Antimicrobial activities for synthesized dyes showed excellent activity against gram-negative organisms such as Pseudomonas aeruginosa and Proteus mirabilis faecalis, whereas very good activity against gram-positive organisms such as Staphylococcus aureus and Enterococcus faecalis with respect to the standard drugs ampicillin and chloramphenicol. Originality/value The principle advantages in this study were that the synthesis of novel synthesized dyes by introducing bisulfonamide-based moieties to increase the antimicrobial activity of the cellulose fabrics could be used as a medical textile, short reaction time and reaction procedure conducted in few steps, the work up is convenient and thus the starting material can be easily prepared.


2017 ◽  
Vol 46 (1) ◽  
pp. 56-63 ◽  
Author(s):  
Monthon Nakpathom ◽  
Buppha Somboon ◽  
Nootsara Narumol ◽  
Rattanaphol Mongkholrattanasit

Purpose The present study aims to focus on the feasibility of using an aqueous extract from the fruit shell of Camellia oleifera Abel as a source of natural colourant in printing-paste preparation for pigment printing of cotton fabric. The effects of pre- and post-mordanting with three common metallic mordants, that is AlK(SO4)2, CuSO4 and FeSO4 on colour yield and colour fastness properties are also investigated. Design/methodology/approach The printing paste was prepared by mixing the concentrated Camellia oleifera Abel fruit shell extract solution with commercially available synthetic thickener and binder. The fabric sample was printed with the prepared printing paste using a flat-screen printing technique. To determine the effects of pre- and post-mordanting, AlK(SO4)2, CuSO4 and FeSO4 mordant aqueous solutions with various concentrations were applied using the pad-dry technique. Comparisons between printing with and without mordants were evaluated in terms of colour strength (K/S values) and colour fastness to washing, light, crocking and perspiration. Findings Without the mordants, the printed fabric had a yellowish brown shade with acceptable colour fastness properties, that is fair to good wash fastness, moderate light fastness, good to very good crocking fastness and fair to good perspiration fastness. The use of mordants, especially CuSO4 and FeSO4, not only enhanced colour strength but also imparted different colours to the fabric. Compared to the unmordanted fabrics, colour fastness properties were mostly comparable or improved in the mordanted fabrics depending on the type and concentration of mordants. Research limitations/implications Although in the case of CuSO4 the light fastness was increased to a good to very good level, it is recommended that the final print be produced with a concentration of less than 0.125 gL−1 to yield the print with the residual amount of Cu metal under the limit, that is less than 50 ppm as regulated by the Oeko-Tex® standard. Practical implications The obtained prints from Camellia oleifera Abel fruit shell extract provided shades with satisfactory colour fastness to washing, light, crocking and perspiration. The extract from Camellia oleifera Abel fruit shell has the potential to be used as an alternative to synthetic dye in the textile industry. Originality/value The use of Camellia oleifera Abel fruit shells, which are considered as abundant byproducts of tea seed oil production, as natural colouring agents for pigment printing of cotton fabric has been reported for the first time. It will minimise the environmental impact of this waste and create more valuable textile products.


Author(s):  
Dr. Suneeta, Et. al.

The main drawback with microorganism's development on fabrics is associated with the maintenance of hygiene and fabric deterioration. In this present investigation a trial has been made to produce an attractive and vibrant textile with eco-friendly antimicrobial dyeing by marigold, a natural resource. Tagetes erecta universally recognized as Marigold is a remarkable source of carotenoids and lutein, grown as a lawn plant. Now a day, lutein is exploding into an indubitably predominant active fitting, employed as an element of the Drugs, Nutrients and Textile Industry. The prospective application of marigold as a characteristic of antimicrobial activity has not been accustomed fully. It is due to the lack of knowledge about its ability and resemblance in material manner. In this work, we have concentrated on the analysis, which was led to deliberate the use of distillate isolate of marigold as an antimicrobial. The antimicrobial competence of the extract was evaluated by coloring on cotton textiles. Testing of the dye ability, its wash quickness and light fastness was done. Educations have validated that antimicrobial coatings have not affected by laundering and shown enhanced colouring effect comprising of fastness to washing, perspiration and rubbing than conservatively dyed textiles. It revealed that the essence of Marigold flower is habitually employed for cotton fabrics as an antimicrobial finish. The samples show very encouraging ends up in terms of antimicrobial resistivity.


2011 ◽  
Vol 81 (18) ◽  
pp. 1903-1915 ◽  
Author(s):  
Ahu Demiroz Gun ◽  
Bahar Tiber

In this study, the color and color fastness properties of the dyed plain knitted fabrics made from 50/50 bamboo/cotton blended yarns with three different stitch lengths are investigated in comparison with those of the similar fabrics made from 50/50 conventional viscose/cotton and 50/50 modal/cotton blended yarns. Abrasion behaviors of the fabrics are assessed by measuring the weight loss and the color values after four different increasing abrasion cycles. The bamboo/cotton fabrics reveal the highest K/S and C* values, but the lowest L* values before abrasion. The lowest weight loss values are obtained for the bamboo/cotton fabrics. Regarding the color properties after abrasion, the bamboo/cotton fabrics show the highest K/S and C* values, but the lowest L* values as in the case of those obtained before abrasion. The highest color difference values (ΔE*) occurred between the beginning and the end of the abrasion test (20000 cycles) and are observed for the bamboo/cotton fabrics. The rubbing, wash and perspiration fastness results of the bamboo/cotton fabrics are found to be worse than those of the other fabrics having viscose/cotton and modal/cotton yarns. However, the highest light fastness results are obtained for the bamboo/cotton fabrics. From the color values after abrasion and the fastness results, it can be concluded that the bamboo/cotton fabrics having the better dyeing properties lose their color more easily than the other fabrics having the viscose/cotton and modal/cotton yarns. The results also indicate that stitch length affects the color values before abrasion and the weight loss and color values after abrasion.


2014 ◽  
Vol 535 ◽  
pp. 662-665 ◽  
Author(s):  
Chotima Sodsangchan ◽  
Jantip Setthayanond ◽  
Potjanart Suwanruji

The objective of this paper was to study the application of Monochlorotriazine-β-cyclodextrin (MCT-β-CD) on cotton fabric and its influence on dyeing and fastness properties of the hot-dyeing reactive dye (with MCT reactive group), Drimarene Red X-6BN, on cotton. The optimum curing condition for MCT-β-CD on cotton was investigated. MCT-β-CD treatment was found to be unaffected on the dyeing properties of the dye on cotton. The color fastness to washing of the dyed fabric was improved in the presence of MCT-β-CD, while the light fastness was unaffected.


2013 ◽  
Vol 821-822 ◽  
pp. 589-592
Author(s):  
Qiu Hong Wang

Natural dye was extracted from the mangosteen pericarps using UE method. The work dealed with the investigation of cotton fabric samples dyed with natural dye. The effects of different dye concentrations and pH values were estimated by the dye-uptake(K)and the color difference(△E). And the effects of different dyeing methods of direct dyeing, pre-mordant and after-mordant were tested when alum was used as a mordant. The highest K and △E were obtained on using pre-mordant method when dye concentration was used as 30g/L and pH value as 3. And the color fastness properties of rubbing, washing and perspiration were tested. Compared with the pre-mordant method, it was quite satisfactory for after-mordant method where its ranged between 2-3 to 4-5.


2020 ◽  
Vol 32 (10) ◽  
pp. 2583-2588
Author(s):  
S. Margrat Sheela ◽  
J. Rosaline Vimala ◽  
M. Stella Bharathy ◽  
A. Agila ◽  
S. Sharmila ◽  
...  

In the present work, cotton fabrics were dyed using the acidified aqueous extract of Psuderanthimum reticulatum leaves with different mordants such as ferrous sulphate, stannous chloride, copper sulphate, potash alum and ferric alum by premordanting technique and various shades were obtained. The washing, perspiration and light fastness properties of the dyed fabrics were carried out by standard methods, ISO 105-C06 A2S-2010, ISO 105 E04-2013 and ISO 105 B02 Methods 3:2014, respectively. Cotton fabrics dyed with copper sulphate and ferric alum showed excellent to very good properties towards the entire fastness tests studied. The bioactive colourant present in the aqueous extract of Psuderanthimum reticulatum responsible for dyeing is anthocyanin pigment and it was identified by chemical test, UV & FTIR spectral and HPLC analysis.


2021 ◽  
pp. 004051752199792
Author(s):  
Yi Ding ◽  
Wu Zhendong ◽  
Zhang Chuanxiong ◽  
Xiao Ruobai ◽  
Xue Wenliang

In digital printing, the fabric print quality can only be evaluated through the color and pattern of printed fabric after printing. The influence of the physical properties of fabric on the printing effect remains unclear. In this paper, the digital print suitability of cotton fabric was defined, and 14 samples of plain cotton fabrics were taken as research objects. In addition, 11 evaluation indexes of cotton fabrics were selected. The evaluation and prediction model of cotton fabric printability was established by principal component analysis. Furthermore, the prediction results of the model were verified by analyzing the colorimetric data of cotton fabric after printing. The result demonstrated that the evaluation model of printing suitability was applicable and can be used to quickly evaluate the printability of cotton fabrics. Particularly, fabric thickness had the greatest influence on printing permeability. In the case of moderate wicking, the higher the whiteness of cotton fabric, the better the color reproducibility after printing. Additionally, the wicking effect also had a great influence on color performance.


2011 ◽  
Vol 331 ◽  
pp. 398-401 ◽  
Author(s):  
Qian Zhu ◽  
Jian Da Cao ◽  
Wang Wei ◽  
Jing Cheng Zhong ◽  
Jia Yao ◽  
...  

Cotton fabric was directly inkjet printed with reactive dye ink, the ink would appear on the permeability of the fabric, the depth of color yield is low, light fastness is poor. Pretreatment agents with different mass fractions had been used to do the pretreatment of the cotton fabric before ink-jet printing, the results showed that: when the concentration of alginate ester or seaweed was between 1.0% -1.5%, the fabrics had the high color yield and the fixation color rate of the dye was the highest. When the amount of NaHCO3 was 3%, the inkjet printing effect of cotton fabrics was the best; color fastness of colors was all good. After Inkjet printing, the best effect can be achieved by steaming the cotton fabrics under the 100 °Csaturated water vapor for 25min: the colors of black, red and yellow of the K / S value were of the maximum, color fastness was fine.


2014 ◽  
Vol 1030-1032 ◽  
pp. 418-421 ◽  
Author(s):  
Rattanaphol Mongkholrattanasit ◽  
Charoon Klaichoi ◽  
Orawan Mudchiew ◽  
Nattaya Punrattanasin ◽  
Nuttanan Sasivatchutikool ◽  
...  

In the present study, cotton fabric has been dyed with natural indigo (Indigofera tentoria) in absence and present ferrous sulfate mordant by using post-mordanting and pad-batch processes. It was observed that with an increase in the dye concentration, the ultraviolet (UV) protection factor (UPF) values good for the cotton fabric. Cotton fabrics dyed with natural indigo showed greenish-blue shade. The fastness properties ranged from good to very good, level. The results confirmed that natural dyes from natural indigo with ferrous sulfate have potential applications in fabric dyeing and in producing UV-protective cotton fabrics.


Sign in / Sign up

Export Citation Format

Share Document