scholarly journals Maximum Thickness Location Selection of High Subsonic Axial Compressor Airfoils and Its Effect on Aerodynamic Performance

2021 ◽  
Vol 9 ◽  
Author(s):  
Chuansijia Tao ◽  
Xin Du ◽  
Jun Ding ◽  
Yizhou Luo ◽  
Zhongqi Wang
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Rise ◽  
Diffusion Factor ◽  
Pressure Loss Coefficient ◽  
Maximum Thickness ◽  
Camber Angle ◽  
Total Pressure Loss Coefficient ◽  
Selection Of

Solidity and camber angle are key parameters with a primary effect on airfoil diffusion. Maximum thickness location has a considerable impact on blade loading distribution. This paper investigates correlations of maximum thickness location, solidity, and camber angle with airfoil performance to choose maximum thickness location quickly for compressor airfoils with different diffusion. The effects of maximum thickness location, solidity, and camber angle on incidence characteristics are discussed based on abundant two-dimensional cascade cases computed through numerical methods. Models of minimum loss incidence, total pressure loss coefficient, diffusion factor, and static pressure rise coefficient are established to describe correlations quantitatively. Based on models, dependence maps of total pressure loss coefficient, diffusion factor, and static pressure rise coefficient are drawn and total loss variation brought by maximum thickness location is analyzed. The study shows that the preferred selection of maximum thickness location can be the most forward one with no serious shock loss. Then, the choice maps of optimal maximum thickness location on different design conditions are presented. The optimal maximum thickness locates at 20–35% chord length. Finally, a database of optimal cases which can meet different loading requirements is provided as a tool for designers to choose geometrical parameters.

Active Separation Control in Circular and Transitioning S-Duct Diffusers Using Vortex Generator Jets

2006 ◽  
Author(s):  
A. M. Pradeep ◽  
R. K. Sullerey
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Vortex Generator ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Separation Control ◽  
Pressure Loss Coefficient ◽  
Distortion Coefficient ◽  
Total Pressure Loss Coefficient

Performance enhancement of three-dimensional S-duct diffusers by separation control using vortex generator jets is the objective of the current experimental investigation. Two different diffuser geometries namely, a circular diffuser and a rectangular–to–circular transitioning diffuser were studied in uniform inflow conditions at a Reynolds number of 7.8 × 105 and the performance evaluation of the diffusers was carried out in terms of static pressure improvement and quality (flow uniformity) of the exit flow. Detailed measurements that included total pressure, velocity distribution, surface static pressure, skin friction and boundary layer measurements were taken and these results are presented here in terms of static pressure rise, distortion coefficient and total pressure loss coefficient at the duct exit. The mass flow rate of the air injected through the VGJ was about 0.06 percent of the main flow for separation control. The distortion coefficient reduced by over 25 percent and the total pressure loss coefficient reduced by about 30 percent in both the diffusers. The physical mechanism of the flow control devices used has been explored using smoke visualization images.

Development of High-Efficiency Half-Ducted Propeller Fan for Air-Conditioners by Blade Tip Shape Modification

2019 ◽  
Author(s):  
Masashi Yoshikawa ◽  
Hiroyuki Toyoda ◽  
Hisashi Daisaka
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Leading Edge ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Trailing Edge ◽  
Pressure Loss Coefficient ◽  
Blade Tip ◽  
Total Pressure Loss Coefficient

Abstract We developed a high-efficiency half-ducted propeller fan to reduce the electric power consumption of the outdoor unit of air conditioner by using computational fluid dynamics (CFD). Total pressure loss coefficient on the cylindrical surface of blade tip started increasing at the middle of the blade, and the region of high total pressure loss coefficient was formed after trailing edge. Therefore, we assumed that decreasing this region helped increasing static pressure efficiency. Limiting stream lines on the pressure surface showed that the flow from leading edge leaked at the middle of the blade tip, so it was assumed that the region of the high total pressure loss coefficient arose from the leakage at the middle of the blade tip. We confirmed that static pressure at the middle of blade tip, which was the leakage point, was low. We assumed that low inward force to the flow caused the leakage. On the other hand, static pressure at trailing edge of the blade tip was high. Therefore, it was found that the inward force could be increased by making the static pressure higher at the meddle of the blade tip. In order to make the static pressure higher at the middle of the blade tip, we attempted to move the maximum camber position of the blade tip from trailing edge side to leading edge side. Calculation results showed leakage at the blade tip decreased and the static pressure efficiency increased by 0.5%. Experimental results showed that the static pressure efficiency increased by 1.7 % and sound pressure level was almost the same. For the above reasons, we found leakage of flow from leading edge could be decreased by adjusting the maximum camber position of the blade tip. Decreasing leakage contributed to increasing static pressure efficiency and decreasing electric power consumption.

scholarly journals Accurate 2-D Modelling of Transonic Compressor Cascade Aerodynamics

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 57 ◽  
Author(s):  
Tommaso Piovesan ◽  
Andrea Magrini ◽  
Ernesto Benini
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Compressor Cascade ◽  
Transonic Compressor ◽  
Pressure Loss Coefficient ◽  
Total Pressure Loss Coefficient

Modern aeronautic fans are characterised by a transonic flow regime near the blade tip. Transonic cascades enable higher pressure ratios by a complex system of shockwaves arising across the blade passage, which has to be correctly reproduced in order to predict the performance and the operative range. In this paper, we present an accurate two-dimensional numerical modelling of the ARL-SL19 transonic compressor cascade. A large series of data from experimental tests in supersonic wind tunnel facilities has been used to validate a computational fluid dynamic model, in which the choice of turbulence closure resulted critical for an accurate reproduction of shockwave-boundary layer interaction. The model has been subsequently employed to carry out a parametric study in order to assess the influence of main flow variables (inlet Mach number, static pressure ratio) and geometric parameters (solidity) on the shockwave pattern and exit status. The main objectives of the present work are to perform a parametric study for investigating the effects of the abovementioned variables on the cascade performance, in terms of total-pressure loss coefficient, and on the shockwave pattern and to provide a quite large series of data useful for a preliminary design of a transonic compressor rotor section. After deriving the relation between inlet and exit quantities, peculiar to transonic compressors, exit Mach number, mean exit flow angle and total-pressure loss coefficient have been examined for a variety of boundary conditions and parametrically linked to inlet variables. Flow visualisation has been used to describe the shock-wave pattern as a function of the static pressure ratio. Finally, the influence of cascade solidity has been examined, showing a potential reduction of total-pressure loss coefficient by employing a higher solidity, due to a significant modification of shockwave system across the cascade.

Relationship Between Optimum Curved Blade Generate Line and Cascade Parameters in Subsonic Axial Compressor

2014 ◽  
Author(s):  
Jing Ling ◽  
Xin Du ◽  
Songtao Wang ◽  
Zhongqi Wang
Keyword(s):  
Aspect Ratio ◽  
Pressure Loss ◽  
Total Pressure ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Angle Variation ◽  
Pressure Loss Coefficient ◽  
Camber Angle ◽  
Curved Blade ◽  
Total Pressure Loss Coefficient

Curved blade has been widely used to reduce the endwall loss, but there is no criterion for curved blade design. Relationship of the optimum curved blade generate line (stack line) and the inlet Mach number, solidity, aspect ratio and camber angle in a linear compressor cascade were researched by optimization method in present paper. The stack line is vertically symmetrical, composed of two third-order Bezier curves and a straight line. The results show that total pressure loss coefficient decreases with the curved height increasing in the present calculate conditions at the same curved angle, and the optimum curved height is 0.5. The total pressure loss coefficient variation with curved angle presents a approximate parabola line type at the same curved height, there is an optimum curved angle, at which the total pressure loss coefficient is minimal. The optimum curved angle variation with the cascade parameters. Optimum curved angle increases with the inlet Ma and camber angle increasing, optimum curved angle variation with inlet Ma shows a polynomial curve type, optimum curved angle varied linearly with camber angle increasing. Optimum curved angle has little changes with solidity and aspect ratio increasing, optimum curved angle is about 6.5° in present conditions, but optimum curved angle will change with the blade loading. The benefit of the optimum curved blade increases with the inlet Mach number and camber angle increasing, and it has little change with solidity and aspect ratio increasing.

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

2021 ◽  
Author(s):  
Feng Li ◽  
Zhao Liu ◽  
Zhenping Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Cooling Performance ◽  
Pressure Loss Coefficient ◽  
Blade Tip ◽  
Total Pressure Loss Coefficient

Abstract The blade tip region of the shroud-less high-pressure gas turbine is exposed to an extremely operating condition with combined high temperature and high heat transfer coefficient. It is critical to design new tip structures and apply effective cooling method to protect the blade tip. Multi-cavity squealer tip has the potential to reduce the huge thermal loads and improve the aerodynamic performance of the blade tip region. In this paper, numerical simulations were performed to predict the aerothermal performance of the multi-cavity squealer tip in a heavy-duty gas turbine cascade. Different turbulence models were validated by comparing to the experimental data. It was found that results predicted by the shear-stress transport with the γ-Reθ transition model have the best precision. Then, the film cooling performance, the flow field in the tip gap and the leakage losses were presented with several different multi-cavity squealer tip structures, under various coolant to mainstream mass flow ratios (MFR) from 0.05% to 0.15%. The results show that the ribs in the multi-cavity squealer tip could change the flow structure in the tip gap for that they would block the coolant and the leakage flow. In this study, the case with one-cavity (1C) achieves the best film cooling performance under a lower MFR. However, the cases with multi-cavity (2C, 3C, 4C) show higher film cooling effectiveness under a higher MFR of 0.15%, which are 32.6%%, 34.2%% and 41.0% higher than that of the 1C case. For the aerodynamic performance, the case with single-cavity has the largest total pressure loss coefficient in all MFR studied, whereas the case with two-cavity obtains the smallest total pressure loss coefficient, which is 7.6% lower than that of the 1C case.

The Influence of Different Rim Seal Geometries on Hot-Gas Ingestion and Total Pressure Loss in a Low-Pressure Turbine

2010 ◽  
Author(s):  
P. Schuler ◽  
W. Kurz ◽  
K. Dullenkopf ◽  
H.-J. Bauer
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Gas Flow ◽  
Low Pressure ◽  
Total Pressure Loss ◽  
Pressure Loss Coefficient ◽  
Low Pressure Turbine ◽  
Hot Gas ◽  
Flow Through ◽  
Total Pressure Loss Coefficient

In order to prevent hot-gas ingestion into the rotating turbo machine’s inside, rim seals are used in the cavities located between stator- and rotor-disc. The sealing flow ejected through the rim seal interacts with the boundary layer of the main gas flow, thus playing a significant role in the formation of secondary flows which are a major contributor to aerodynamic losses in turbine passages. Investigations performed in the EU project MAGPI concentrate on the interaction between the sealing flow and the main gas flow and in particular on the influence of different rim seal geometries regarding the loss-mechanism in a low-pressure turbine passage. Within the CFD work reported in this paper static simulations of one typical low-pressure turbine passage were conducted containing two different rim seal geometries, respectively. The sealing flow through the rim seal had an azimuthal velocity component and its rate has been varied between 0–1% of the main gas flow. The modular design of the computational domain provided the easy exchange of the rim seal geometry without remeshing the main gas flow. This allowed assessing the appearing effects only to the change of rim seal geometry. The results of this work agree with well-known secondary flow phenomena inside a turbine passage and reveal the impact of the different rim seal geometries on hot-gas ingestion and aerodynamic losses quantified by a total pressure loss coefficient along the turbine blade. While the simple axial gap geometry suffers considerable hot-gas ingestion upstream the blade leading edge, the compound geometry implying an axial overlapping presents a more promising prevention against hot-gas ingestion. Furthermore, the effect of rim seals on the turbine passage flow field has been identified applying adequate flow visualisation techniques. As a result of the favourable conduction of sealing flow through the compound geometry, the boundary layer is less lifted by the ejected sealing flow, thus resulting in a comparatively reduced total pressure loss coefficient over the turbine blade.

Numerical Simulation of Deposition Phenomena on High-Pressure Turbine Vane Using UPACS

2019 ◽  
Author(s):  
Kenta Mizutori ◽  
Koji Fukudome ◽  
Makoto Yamamoto ◽  
Masaya Suzuki
Keyword(s):  
Numerical Simulation ◽  
High Pressure ◽  
Flow Field ◽  
Pressure Loss ◽  
Total Pressure ◽  
Total Pressure Loss ◽  
High Pressure Turbine ◽  
Pressure Loss Coefficient ◽  
Turbine Vane ◽  
Total Pressure Loss Coefficient

Abstract We performed numerical simulation to understand deposition phenomena on high-pressure turbine vane. Several deposition models were compared and the OSU model showed good adaptation to any flow field and material, so it was implemented on UPACS. After the implementation, the simulations of deposition phenomenon in several cases of the flow field were conducted. From the results, particles adhere on the leading edge and the trailing edge side of the pressure surface. Also, the calculation of the total pressure loss coefficient was conducted after computing the flow field after deposition. The total pressure loss coefficient increased after deposition and it was revealed that the deposition deteriorates aerodynamic performance.

Effect of Tip Gap Variation on the Performance of the Transonic Fan Stage With Tandem Stator

2019 ◽  
Author(s):  
K. Ananthakrishnan ◽  
Shyama Prasad Das ◽  
B. V. S. S. S. Prasad
Keyword(s):  
Pressure Loss ◽  
Total Pressure ◽  
Axial Compressor ◽  
Compressor Stage ◽  
Tip Leakage ◽  
Pressure Loss Coefficient ◽  
Overall Performance ◽  
Transonic Fan ◽  
Total Pressure Loss Coefficient ◽  
Transonic Rotor

Abstract The main goal of modern axial compressor development is to increase the power to weight ratio with higher efficiency. In the present investigation, highly loaded single stage axial compressor with tandem stator vanes is used. Tandem vanes help in attaining the compact compressor stage along with high pressure loading. It is designed for a stage pressure ratio of 2, mass flow rate of 9.02 kg/s operating at 30800 rpm resulting in transonic flow field. The aerodynamic performance of this compressor detoriates due to the tip leakage and secondary flows. Steady-state numerical investigation is carried out to study the flow structures near the tip region of transonic rotor and how different tip gaps influence the overall performance of the compressor. Further the effects of tip leakage flow variation on the performance of tandem vanes are also highlighted. Transonic fan stage with baseline tip gap of 0.5mm is analyzed along with different tip clearance values ranging from 0 % to 3 % of axial chord. Three-dimensional viscous Reynolds Averaged Navier Stokes (RANS) equations are solved using SST k-ω turbulence model. Computational domain discretized with high quality hexahedral elements (Y+ < 2) in AUTOGRID, Numeca. The numerical procedure is verified against the experimental results of Rotor37 transonic rotor test case. Tip leakage losses contribute a substantial amount to the total loss of stage. Overall performance and the stall characteristics for the compressor stage has been evaluated for different tip gap variations.. Further, the topological properties are exploited to visualize the critical points and separation lines on rotor and tandem vanes. Increase in rotor total pressure loss coefficient is observed with increasing tip gap. In contrary, overall total pressure loss coefficient improves for smaller tip gap values and then detoriates. It is observed optimum tip gap height lies close to the 1.125mm, 2% of baseline design value.

scholarly journals Preliminary Experimental Study on Pressure Loss Coefficients of Exhaust Manifold Junction

2014 ◽  
Vol 2014 ◽  
pp. 1-10
Author(s):  
Xiao-lu Lu ◽  
Kun Zhang ◽  
Wen-hui Wang ◽  
Shao-ming Wang ◽  
Kang-yao Deng
Keyword(s):  
Mass Flow ◽  
Pressure Loss ◽  
Total Pressure ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Flow Ratio ◽  
Pressure Loss Coefficient ◽  
Loss Coefficients ◽  
Total Pressure Loss Coefficient ◽  
Mass Flow Ratio

The flow characteristic of exhaust system has an important impact on inlet boundary of the turbine. In this paper, high speed flow in a diesel exhaust manifold junction was tested and simulated. The pressure loss coefficient of the junction flow was analyzed. The steady experimental results indicated that both of static pressure loss coefficientsL13andL23first increased and then decreased with the increase of mass flow ratio of lateral branch and public manifold. The total pressure loss coefficientK13always increased with the increase of mass flow ratio of junctions 1 and 3. The total pressure loss coefficientK23first increased and then decreased with the increase of mass flow ratio of junctions 2 and 3. These pressure loss coefficients of the exhaust pipe junctions can be used in exhaust flow and turbine inlet boundary conditions analysis. In addition, simulating calculation was conducted to analyze the effect of branch angle on total pressure loss coefficient. According to the calculation results, total pressure loss coefficient was almost the same at low mass flow rate of branch manifold 1 but increased with lateral branch angle at high mass flow rate of branch manifold 1.

Optimization of Tandem Blade Based on Improved Particle Swarm Algorithm

2016 ◽  
Author(s):  
Song Zhaoyun ◽  
Bo Liu ◽  
Mao Xiaochen ◽  
Lu Xiaofeng
Keyword(s):  
Particle Swarm Optimization ◽  
Pressure Loss ◽  
Total Pressure ◽  
Particle Swarm ◽  
Loss Coefficient ◽  
Total Pressure Loss ◽  
Swarm Optimization ◽  
Improved Particle Swarm Optimization ◽  
Pressure Loss Coefficient ◽  
Total Pressure Loss Coefficient

To improve the design quality of high-turning tandem blade, a coupling optimization system for the shape and relative position of tandem blades was developed based on an improved particle swarm optimization algorithm and NURBS parameterization. First of all, to increase convergence speed and avoid local optima of particle swarm optimization (PSO), an improved particle swarm optimization (IPSO) is formulated based on adaptive selection of particle roles, adaptive control of parameters and population diversity control. Then experiments are carried out using test functions to illustrate the performance of IPSO and to compare IPSO with some PSOs. The comparison indicates IPSO can obtain excellent convergence speed and simultaneously keep the best reliability. In addition, the coupling optimization system is validated by optimizing a large-turning tandem blade. Optimization results illustrate IPSO can obviously increase the optimization speed and reduce the time and cost of optimization. After optimization, at design condition, the total pressure loss coefficient of the optimized blade is decreased by 40.4%, and the static pressure ratio of optimized blade is higher and the total pressure loss coefficient is smaller at all incidence angles. In addition, properly reducing the gap area of tandem blade can effectively reduce the friction loss of the blade boundary layer and the mixing loss created by mixing the gap fluid and the mainstream fluid.

Sign in / Sign up

Export Citation Format

Share Document