scholarly journals Leading-Edge Roughness Affecting Diamond-Wing Aerodynamic Characteristics

Aerospace ◽  
2018 ◽  
Vol 5 (3) ◽  
pp. 98 ◽  
Author(s):  
Andrei Buzica ◽  
Lisa Debschütz ◽  
Florian Knoth ◽  
Christian Breitsamter
Keyword(s):  
Reynolds Number ◽  
Surface Pressure ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Coefficients ◽  
Number Range ◽  
Edge Roughness ◽  
Vortex Separation ◽  
Roughness Size

Diamond wing configurations for low signature vehicles have been studied in recent years. Yet, despite numerous research on highly swept, sharp edged wings, little research on aerodynamics of semi-slender wings with blunt leading-edges exists. This paper reports on the stall characteristics of the AVT-183 diamond wing configuration with variation of leading-edge roughness size and Reynolds number. Wind tunnel testing applying force and surface pressure measurements are conducted and the results presented and analysed. For the investigated Reynolds number range of 2.1 × 10 6 ≤ R e ≤ 2.7 × 10 6 there is no significant influence on the aerodynamic coefficients. However, leading-edge roughness height influences the vortex separation location. Trip dots produced the most downstream located vortex separation onset. Increasing the roughness size shifts the separation onset upstream. Prior to stall, global aerodynamic coefficients are little influenced by leading-edge roughness. In contrast, maximum lift and maximum angle of attack is reduced with increasing disturbance height. Surface pressure fluctuations show dominant broadband frequency peaks, distinctive for moderate sweep vortex breakdown. The experimental work presented here provides insights into the aerodynamic characteristics of diamond wings in a wide parameter space including a relevant angle of attack range up to post-stall.

Investigation of aerodynamic coefficients at Mach 6 over conical, hemispherical and flat-face spiked body

2017 ◽  
Vol 121 (1245) ◽  
pp. 1711-1732 ◽  
Author(s):  
R. Kalimuthu ◽  
R. C. Mehta ◽  
E. Rathakrishnan
Keyword(s):  
Flow Field ◽  
Blunt Body ◽  
Angle Of Attack ◽  
Separated Flow ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Geometrical Parameters ◽  
Aerodynamic Coefficients ◽  
Aerodynamic Forces ◽  
Flow Field Characteristics

ABSTRACTA forward spike attached to a blunt body significantly alters its flow field characteristics and influences aerodynamic characteristics at hypersonic flow due to formation of separated flow and re-circulation region around the spiked body. An experimental investigation was performed to measure aerodynamic forces for spikes blunt bodies with a conical, hemispherical and flat-face spike at Mach 6 and at an angle-of-attack range from 0° to 8° and length-to-diameterL/Dratio of spike varies from 0.5 to 2.0, whereLis the length of the spike andDis diameter of blunt body. The shape of the leading edge of the spiked blunt body reveals different types of flow field features in the formation of a shock wave, shear layer, flow separation, re-circulation region and re-attachment shock. They are analysed with the help of schlieren pictures. The shock distance ahead of the hemisphere and the flat-face spike is compared with the analytical solution and is showing satisfactory agreement with the schlieren pictures. The influence of geometrical parameters of the spike, the shape of the spike tip and angle-of-attack on the aerodynamic coefficients are investigated by measuring aerodynamic forces in a hypersonic wind tunnel. It is found that a maximum reduction of drag of about 77% was found for hemisphere spike ofL/D= 2.0 at zero angle-of-attack. Consideration for compensation of increased pitching moment is required to stabilise the aerodynamic forces.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

scholarly journals Lift Generation of an Elliptical Airfoil at a Reynolds Number of 1000

2019 ◽  
Vol 16 (2) ◽  
pp. 6738-6752
Author(s):  
S. Tobing
Keyword(s):  
Reynolds Number ◽  
Unsteady Aerodynamics ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Two Dimensional ◽  
Hovering Flight ◽  
Number Range ◽  
High Production ◽  
Passenger Aircraft ◽  
3D Wing

Bumblebees cannot fly! That conclusion is likely to be drawn by scientists who analysed the insect using aerodynamics of stationary wings such as that of a passenger aircraft. Looking at the insect again using a newfound understanding of unsteady aerodynamics; it is clear why bumblebees can fly. Bumblebees utilise mechanisms behind unsteady aerodynamics such as leading-edge vortices (LEVs) formation, wake capture, and rapid end-of-stroke rotation to generate forces that enable the insect to fly. This study focuses on two-dimensional (2D) elliptical airfoil. Earlier works found the aerodynamic characteristics of an elliptical airfoil to differ greatly from a conventional airfoil, and that this airfoil shape could generate the counter-rotating vortices used by insects to generate lift. Therefore, this research aims to study the lift generation of a bumblebee-inspired elliptical airfoil in a normal hovering flight. This study focuses on hovering flight with the insect flies in a nearly stationary position, which explains the importance of lift generation to stay aloft. The motion of the elliptical airfoil is inspired by the flapping kinematics of bumblebees at a typical Reynolds number range of . It is found that the current two-dimensional model is capable of capturing the counter-rotating vortices and correlates the formation of these structures to a high production of lift. These results show that bumblebees utilise these counter-rotating vortices to generate lift enough to fly in hovering flight. This results also indicate that flapping 2D elliptical airfoils can be used to investigate their 3D wing counterparts, which translate to a reduced time and computing costs.

Influence of tubercles’ spanwise distribution on swept wings for unmanned aerial vehicles

2020 ◽  
pp. 095441002091958
Author(s):  
Charalampos Papadopoulos ◽  
Vasilis Katsiadramis ◽  
Kyros Yakinthos
Keyword(s):  
Reynolds Number ◽  
Unmanned Aerial Vehicles ◽  
Numerical Study ◽  
Computational Study ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Number Range ◽  
Aerial Vehicles ◽  
Reynolds Number Range

In this work, a 3D numerical study on the influence of the spanwise distribution of tubercles on a unmanned aerial vehicle wing is presented. The idea of using tubercles in aeronautics comes from the humpback whale (Megaptera novaeangliae) which has a characteristic flipper, with a spanwise scalloped leading edge, creating an almost sinusoidal shape, consisting of bumps called tubercles. The whale uses this layout in order to achieve high underwater maneuverability. Early experimental research showed a great potential in enhancing the 3D aerodynamic characteristics of a wing. Most of the existing experimental results concern infinite wings (2D) models and are accompanied with substantial loss in lift and increase in drag in pre-stall region. On the other hand, 3D finite models have displayed a better overall aerodynamic performance (increased lift and moment, but also, decreased drag). At a range of Reynolds number between 500,000 and 1,000,000 (based on the mean chord of the flipper), tubercles act as virtual fences, introducing a pair of counter rotating vortices that delays the stall of the flipper, a phenomenon that the whales exploit to perform sharp turns and catch their prey. The aforementioned Reynolds number range is the same as the operational Reynolds number for typical unmanned aerial vehicles. To assess the influence of the tubercles installation on UAV wings, a full 3D computational study is carried-out with the use of CFD tools which at a first phase are validated and calibrated with the available literature experimental data. Then, computations are performed for different spanwise tubercles distributions. The results show that there is a noticeable potential on controlling the flow on the wings of a UAV operating in a Reynolds number range between 500,000 and 1,000,000 (based on UAV’s wing mean chord), which can lead to an aerodynamic performance and efficiency increase.

scholarly journals Numerical 3D study on the influence of spanwise distribution of tubercles on wings for UAV applications

2019 ◽  
Vol 304 ◽  
pp. 02014
Author(s):  
Charalampos Papadopoulos ◽  
Vasilis Katsiadramis ◽  
Kyros Yakinthos
Keyword(s):  
Reynolds Number ◽  
Numerical Study ◽  
Computational Study ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Performance ◽  
Number Range ◽  
Reynolds Number Range ◽  
Efficiency Increase ◽  
Sinusoidal Shape

In this work, a 3D numerical study on the influence of the spanwise distribution of tubercles for UAV applications is presented. The idea of using tubercles in aeronautics comes from the humpback whale (Megaptera novaeangliae) which has a characteristic flipper, with a spanwise scalloped leading edge, creating an almost sinusoidal shape, consisting of bumps called tubercles. Early experimental research showed a great potential in enhancing the 3D aerodynamic characteristics of a wing. Most of the existing experimental results concern infinite wings (2D) models and are accompanied with substantial loss in lift and increase in drag in pre–stall region. On the other hand, finite models (3D) have displayed a better overall aerodynamic performance (increased lift and moment, but also decreased drag). At a range of Reynolds number between 500,000 and 1,000,000 (based on the mean chord of the flipper), tubercles act as virtual fences, introducing a pair of counter rotating vortices that delays the stall of the flipper, a phenomenon that the whales use to perform sharp turns and catch their prey. The aforementioned Reynolds number range is the same as the operational Reynolds number for typical Unmanned Aerial Vehicles (UAV). To assess the influence of the tubercles installation on UAV wings, a full 3D computational study is carried-out, with the use of CFD tools that at a first phase are validated and calibrated with available in the literature experimental data. Then, computations are performed, for different spanwise tubercles distributions. The results show that there is a noticeable potential on controlling the flow on the wings of a UAV operating in a Reynolds number range between 500,000 and 1,000,000 (based on UAV’s wing mean chord), which can lead to an aerodynamic performance and efficiency increase.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

Acoustic and phase portrait analysis of leading-edge roughness element on laminar separation bubbles at low Reynolds number flow

2021 ◽  
pp. 095441002110443
Author(s):  
Hossein Jabbari ◽  
Esmaeili Ali ◽  
Mohammad Hasan Djavareshkian
Keyword(s):  
Reynolds Number ◽  
Phase Portrait ◽  
Separation Bubble ◽  
Roughness Element ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Suction Side ◽  
Laminar Separation ◽  
Roughness Elements ◽  
Edge Roughness

Since laminar separation bubbles are neutrally shaped on the suction side of full-span wings in low Reynolds number flows, a roughness element can be used to improve the performance of micro aerial vehicles. The purpose of this article was to investigate the leading-edge roughness element’s effect and its location on upstream of the laminar separation bubble from phase portrait point of view. Therefore, passive control might have an acoustic side effect, especially when the bubble might burst and increase noise. Consequently, the effect of the leading-edge roughness element features on the bubble’s behavior is considered on the acoustic pressure field and the vortices behind the NASA-LS0417 cross-section. The consequences express that the distribution of roughness in the appropriate dimensions and location could contribute to increasing the performance of the airfoil and the interaction of vortices produced by roughness elements with shear layers on the suction side has increased the sound frequency in the relevant sound pressure level (SPL). The results have demonstrated that vortex shedding frequency was increased in the presence of roughness compared to the smooth airfoil. Also, more complexity of the phase portrait circuits was found, retrieved from velocity gradient limitation. Likewise, the highest SPL is related to the state where the separation bubble phenomenon is on the surface versus placing roughness elements on the leading edge leads to a negative amount of SPL.

Aerodynamic Characteristics of a Deformable Membrane Aerofoil

2014 ◽  
Vol 553 ◽  
pp. 255-260
Author(s):  
Viktor Šajn ◽  
Igor Petrović ◽  
Franc Kosel
Keyword(s):  
Experimental Study ◽  
Reynolds Number ◽  
Wind Tunnel ◽  
Lift Coefficient ◽  
Fluid Structure Interaction ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Relative Difference ◽  
Structure Interaction ◽  
Deformable Membrane

In the paper, numerical and experimental study of low Reynolds number airflow around the deformable membrane airfoil (DMA) is presented. Simulations of a fluid-structure interaction between the fluid and the DMA were performed. In the experiment, the DMA model was made from a thin PVC sheet, which was wrapped around the steel rod at the leading and trailing edge. Measurements were performed in a wind tunnel at a chord Reynolds number of 85.7·103, over the angle of attack range from 0° to 15° and DMA shortening ratio from 0.025 to 0.150. Simulations were in an agreement with the experiment, since the average relative difference of coefficient of lift was smaller than 7.3%. For the same value of Reynolds number, DMA shows improved lift coefficient Cy= 2.18, compared to standard rigid airfoils.

scholarly journals Determine Aerodynamic Characteristics for FX63-137 Aerofoil by Using Subsonic Wind Tunnel

2014 ◽  
Vol 695 ◽  
pp. 651-654 ◽  
Author(s):  
Magedi Moh M. Saad ◽  
Norzelawati Asmuin
Keyword(s):  
Reynolds Number ◽  
Aluminum Alloy ◽  
Wind Tunnel ◽  
Low Reynolds Number ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Cnc Machine ◽  
Subsonic Wind Tunnel ◽  
Low Reynolds

This paper is primarily concentrated with determining aerodynamic characteristics and choosing the best angle of attack at a maximum lift and low drag for the FX 63-137 aerofoil at a low Reynolds number and a speed of 20m/s and 30m/s, by using subsonic wind tunnel through manufacturing the aerofoil by aluminum alloy using a CNC machine. The proposed methodology is divided into several stages. Firstly, manufacturing the aerofoil using an aluminum alloy. Secondly, the testing process is carried out using subsonic wind tunnel. Thirdly, the results are displayed and compared with results produced from related works, in order to find out the best angle of attack at a maximum lift.

Sign in / Sign up

Export Citation Format

Share Document