scholarly journals The Influence of Flow Rates on Pressure Fluctuation in the Pump Mode of Pump-Turbine with Splitter Blades

2020 ◽  
Vol 10 (19) ◽  
pp. 6752
Author(s):  
Ping Huang ◽  
Yajing Xiao ◽  
Jinfeng Zhang ◽  
Haikun Cai ◽  
Haiqin Song
Keyword(s):  
Pressure Fluctuation ◽  
Draft Tube ◽  
Guide Vane ◽  
Pump Mode ◽  
Pump Turbine ◽  
Flow Rates ◽  
Guide Vanes ◽  
Rotor Stator Interaction ◽  
Computational Fluid Dynamics Cfd ◽  
The Stability

This paper takes a pump-turbine as the research subject and, based on the Computational Fluid Dynamics (CFD) numerical method and combined with test data, investigates the pressure fluctuation characteristics in the pump mode and analyzes the pressure fluctuation characteristics at 0.75 Qd, 1.0 Qd and 1.25 Qd when the guide vane opening is 17.5°. The results showed that the protruding frequencies of pressure fluctuation in the bladeless region were mainly 5 fn, 10 fn and 20 fn, and the main frequencies in the runner area and near the outlet wall of the draft tube were 16 fn and 5 fn, respectively. At different heights for the guide vanes, the pressure fluctuation in the bladeless region had significant differences, and the pressure fluctuation near the bottom ring was the most intense. The amplitude of the rotor–stator interaction frequency continuously attenuates from the bladeless region to the outlet of the stay vanes, and the amplitude attenuation of each frequency is mainly concentrated in the area of the guide vanes. In this paper, the influence of different flow rates on the pressure fluctuation in the pump mode is analyzed, which provides a theoretical reference for the stability and further study of pump-turbines.

scholarly journals Effect of Guide Vane Openings and Different Flow Rates on Characteristics in Pump Mode of Pump-turbine with Splitter Blades

2021 ◽  
Vol 1081 (1) ◽  
pp. 012016
Author(s):  
Jinfeng Zhang ◽  
Yajing Xiao ◽  
Shibin Jin ◽  
Haikun Cai ◽  
Haiqing Song
Keyword(s):  
Guide Vane ◽  
Pump Mode ◽  
Pump Turbine ◽  
Flow Rates

scholarly journals Distribution of Pressure Fluctuations in a Prototype Pump Turbine at Pump Mode

2014 ◽  
Vol 6 ◽  
pp. 923937 ◽  
Author(s):  
Yuekun Sun ◽  
Zhigang Zuo ◽  
Shuhong Liu ◽  
Jintao Liu ◽  
Yulin Wu
Keyword(s):  
Mass Flow ◽  
Pressure Fluctuations ◽  
Dominant Frequency ◽  
Pump Mode ◽  
Pump Turbine ◽  
Guide Vanes ◽  
Path Direction ◽  
Mass Flow Rates ◽  
Operating Points ◽  
Spiral Casing

Pressure fluctuations are very important characteristics in pump turbine's operation. Many researches have focused on the characteristics (amplitude and frequencies) of pressure fluctuations at specific locations, but little researches mentioned the distribution of pressure fluctuations in a pump turbine. In this paper, 3D numerical simulations using SSTk − ω turbulence model were carried out to predict the pressure fluctuations distribution in a prototype pump turbine at pump mode. Three operating points with different mass flow rates and different guide vanes’ openings were simulated. The numerical results show how pressure fluctuations at blade passing frequency (BPF) and its harmonics vary along the whole flow path direction, as well as along the circumferential direction. BPF is the first dominant frequency in vaneless space. Pressure fluctuation component at this frequency rapidly decays towards upstream (to draft tube) and downstream (to spiral casing). In contrast, pressure fluctuations component at 3BPF spreads to upstream and downstream with almost constant amplitude. Amplitude and frequencies of pressure fluctuations also vary along different circumferential locations in vaneless space. When the mass flow and guide vanes’ opening are different, the distribution of pressure fluctuations along the two directions is different basically.

scholarly journals Experimental Research on the Rotating Stall of a Pump Turbine in Pump Mode

Water ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 2426
Author(s):  
Xue ◽  
Liu ◽  
Lu ◽  
Gao ◽  
Meng
Keyword(s):  
Flow Field ◽  
Experimental Research ◽  
Flow Rate ◽  
Guide Vane ◽  
Rotating Stall ◽  
Dynamics Simulation ◽  
Positive Slope ◽  
Pump Mode ◽  
Pump Turbine ◽  
Pump Performance

The rotating stall is an unstable flow phenomenon of pump turbines in pump mode, which is of increasing concern to scientists and engineers working on pump turbines. However, at present, various studies are carried out based on CFD (computational fluid dynamics) simulation, while directly measured data and experimental research on flow fields are seldom reported. By utilizing PIV (particle image velocimetry) measuring equipment, the flow field within the guide vane zone of a low specific speed pump turbine in pump mode was measured. By measuring and analyzing the transient flow field, the evolutionary process of the rotating stall within the guide vane passages was determined. We found that for all three tested guide vane openings, regardless of whether the positive slope appeared or not, a pre-stall operating point was found for each opening in the process of decreasing the flow rate. The analysis of the loss within the flow field indicated that the dissipation-induced loss increased greatly after the rotating stall appeared. The pump performance curves at the three guide vane openings showed an inflection at the pre-stall point. When the flow rate is larger than that of the pre-stall point, the head of the pump turbine dramatically increases as the flow rate decreases. However, when the flow rate is smaller than the pre-stall point, such increases noticeably slows down.The research results showed that whether the positive slope on the pump performance curve occurred or not, instability caused by the rotating stall should be of great concern.

scholarly journals Numerical analysis of pressure fluctuation in a multiphase rotodynamic pump with air–water two-phase flow

2019 ◽  
Vol 74 ◽  
pp. 18 ◽  
Author(s):  
Wenwu Zhang ◽  
Zhiyi Yu ◽  
Yongjiang Li ◽  
Jianxin Yang ◽  
Qing Ye
Keyword(s):  
Pressure Fluctuation ◽  
Two Phase Flow ◽  
Guide Vane ◽  
Fluid Model ◽  
Pure Water ◽  
Maximum Amplitude ◽  
Phase Flow ◽  
Two Phase ◽  
Rotor Stator Interaction ◽  
Two Fluid Model

Pressure fluctuation in single-phase pumps has been studied widely, while less attention has been paid to research on multiphase pumps that are commonly used in the petroleum chemical industry. Therefore, this study investigates the pressure fluctuation for a multiphase rotodynamic pump handling air–water two-phase flow. Simulations based on the Euler two-fluid model were carried out using ANSYS_CFX16.0 at different Inlet Gas Void Fractions (IGVFs) and various flow rate values. Under conditions of IGVF = 0% (pure water) and IGVF = 15%, the accuracy of the numerical method was tested by comparing the experimental data. The results showed that the rotor–stator interaction was still the main generation driver of pressure fluctuation in gas–liquid two-phase pumps. However, the fluctuation near the impeller outlet ascribe to the rotor–stator interaction was weakened by the complex gas–liquid flow. For the different IGVF, the variation trend of fluctuation was similar along the streamwise direction. That is, the fluctuation in the impeller increased before decreasing, while in the guide vane it decreased gradually. Also, the fluctuation in the guide vane was generally greater than for the impeller and the maximum amplitude appeared in the vicinity of guide vane inlet.

Influence of Guide Vane Setting in Pump Mode on Performance Characteristics of a Pump-Turbine

2017 ◽  
Vol 10 (2) ◽  
pp. 154-163 ◽  
Author(s):  
Deyou Li ◽  
Hongjie Wang ◽  
Torbjørn K. Nielsen ◽  
Ruzhi Gong ◽  
Xianzhu Wei ◽  
...  
Keyword(s):  
Guide Vane ◽  
Performance Characteristics ◽  
Pump Mode ◽  
Pump Turbine

Lateral Fluid Forces on Whirling Centrifugal Impeller (1st Report: Theory)

1987 ◽  
Vol 109 (2) ◽  
pp. 94-99 ◽  
Author(s):  
H. Shoji ◽  
H. Ohashi
Keyword(s):  
Potential Flow ◽  
Guide Vane ◽  
Flow Theory ◽  
Operating Conditions ◽  
Centrifugal Impeller ◽  
Flow Rates ◽  
Guide Vanes ◽  
Fluid Forces ◽  
Damping Effect ◽  
Whirling Motion

Lateral fluid forces acting on a rotating centrifugal impeller in whirling motion are analyzed using unsteady potential flow theory. Impellers operating in diffusers with and without vanes are modeled and the fluid forces calculated for different whirl speeds and flow rates. The influences of these parameters are clarified by parametric calculations. The results for whirling impellers operating in vaneless diffusers show that the fluid forces exert a damping effect on the rotor whirling motion at all operating conditions. The results for impellers operating in vaned diffusers or guide vanes show that the time averaged values of fluid forces remain almost unchanged, while there are significant instantaneous fluctuations due to the impeller/guide vane interactions.

scholarly journals Investigating the Performance of a Super High-head Francis Turbine under Variable Discharge Conditions Using Numerical and Experimental Approach

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3868 ◽  
Author(s):  
Zheming Tong ◽  
Hao Liu ◽  
Jianfeng Ma ◽  
Shuiguang Tong ◽  
Ye Zhou ◽  
...  
Keyword(s):  
Draft Tube ◽  
Numerical Models ◽  
Guide Vane ◽  
Maximum Velocity ◽  
Francis Turbine ◽  
Inlet Pipe ◽  
Guide Vanes ◽  
Flow Acceleration ◽  
High Head ◽  
Reduced Scale

A super high-head Francis turbine with a gross head of nearly 700 m was designed with computational fluid dynamics (CFD) simulation and laboratory tests. Reduced-scale (1:3.7) physical and numerical models of the real-scale prototype were created to investigate the hydraulic performance. According to the CFD analysis, a strong rotor–stator interaction (RSI) between guide vanes and runner blades is observed as a result of the high-speed tangential flow towards runner created by the super high water head as well as the small gaps between the radial blades. At the designed best efficiency point (BEP), there is no significant flow recirculation inside the flow passage and minor loss occurs at the trailing edge of the stay vanes and guide vanes. Maximum velocity is observed at runner inlets due to flow acceleration through the narrow passages between the guide vanes. The elbow-shaped draft tube gradually decreases the flow velocity to keep the kinetic energy loss at a minimum. The laboratory test was conducted on a reduced-scale physical model to investigate the pressure pulsations and guide vane torque (GVT) under variable-discharge configurations, which are key concerns in the design of a high head turbine. Pressure sensor networks were installed at the inlet pipe, vaneless space and draft tube, respectively. The most intense pressure variation occurs at the inlet pipe and elbow at 0.04–0.2 GVOBEP and 1.5–1.8 GVOBEP with a low frequency about 0.3 times of the runner frequency, while the vibration in vaneless zone performs stable with the blade passing frequency caused by RSI. The GVT shows a declining trend and then keeps stable as GVOs increases at synchronized condition. For the misaligned conditions, the torque of adjacent guide vanes differs a lot except at the synchronous angle and maximum absolute value at least doubles than the synchronized condition.

Effect of interface condition on the hydraulic characteristics of a pump-turbine at various guide vane opening conditions in pump mode

2020 ◽  
Vol 154 ◽  
pp. 986-1004 ◽  
Author(s):  
Jun-Won Suh ◽  
Seung-Jun Kim ◽  
Jin-Hyuk Kim ◽  
Won-Gu Joo ◽  
Jungwan Park ◽  
...  
Keyword(s):  
Guide Vane ◽  
Interface Condition ◽  
Hydraulic Characteristics ◽  
Pump Mode ◽  
Pump Turbine
Sign in / Sign up

Export Citation Format

Share Document