scholarly journals A Voltage Multiplier Circuit Based Quadratic Boost Converter for Energy Storage Application

2020 ◽  
Vol 10 (22) ◽  
pp. 8254
Author(s):  
Javed Ahmad ◽  
Mohammad Zaid ◽  
Adil Sarwar ◽  
Chang-Hua Lin ◽  
Shafiq Ahmad ◽  
...  
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Voltage Gain ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Power Application ◽  
High Output Voltage ◽  
Multiplier Circuit

In this paper, a new transformerless high voltage gain dc-dc converter is proposed for low and medium power application. The proposed converter has high quadratic gain and utilizes only two inductors to achieve this gain. It has two switches that are operated simultaneously, making control of the converter easy. The proposed converter’s output voltage gain is higher than the conventional quadratic boost converter and other recently proposed high gain quadratic converters. A voltage multiplier circuit (VMC) is integrated with the proposed converter, which significantly increases the converter’s output voltage. Apart from a high output voltage, the proposed converter has low voltage stress across switches and capacitors, which is a major advantage of the proposed topology. A hardware prototype of 200 W of the proposed converter is developed in the laboratory to validate the converter’s performance. The efficiency of the converter is obtained through PLECS software by incorporating the switching and conduction losses.

scholarly journals High gain multiphase boost converter based-on capacitor clamping structure

2021 ◽  
Vol 24 (2) ◽  
pp. 689
Author(s):  
Oday Saad Fares ◽  
Jasim Farhood Hussen
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Low Voltage ◽  
High Gain ◽  
Industrial Applications ◽  
Boost Converter ◽  
Power Device ◽  
Voltage Gain ◽  
High Voltage Gain ◽  
And Performance

<p>In the last few years, the non-isolated dc converters involving high voltage gain with adequate performance are becoming quite popular in industrial applications. This is resulting in high voltage and current stress on the power device (switches and diodes), as well as a limited output voltage with a high duty cycle. This paper proposes a multi-phase non-isolated boost converter that uses capacitor clamping to increase output voltage while reducing stress across the power device. There are two stages in the proposed converter (first stage is three inductors and three switches and the second stage is clamper circuit of three capacitors and three diodes). The proposed converter is high voltage gain, with low voltage stress through switches transistors. To justify the theoretical analysis, the concept was validated through mathematical analysis and by simulation using MATLAB/SIMULINK. The results carried out the results permit the converter behavior and performance to be accurately.</p>

A ZVS DC-DC Converter with High Voltage Gain for Fuel Cell Systems

2014 ◽  
Vol 573 ◽  
pp. 83-88
Author(s):  
A. Marikkannan ◽  
B.V. Manikandan ◽  
S. Jeyanthi
Keyword(s):  
Fuel Cell ◽  
High Voltage ◽  
Output Voltage ◽  
System Analysis ◽  
Clean Energy ◽  
High Gain ◽  
Boost Converter ◽  
Voltage Gain ◽  
Zero Voltage Switching ◽  
High Voltage Gain

The interest toward the application of fuel cells is increasing in the last years mainly due to the possibility of highly efficient decentralized clean energy generation. The output voltage of fuel-cell stacks is generally below 50 V. Consequently, low-power applications with high output voltage require a high gain for proper operation. A zero-voltage-switching (ZVS) dc–dc converter with high voltage gain is proposed for fuel cell as a front-end converter. It consists of a ZVS boost converter stage and a ZVS half-bridge converter stage and two stages are merged into a single stage. The ZVS boost converter stage provides a continuous input current and ZVS operation of the power switches. The ZVS half-bridge converter stage provides a high voltage gain. The principle of operation and system analysis are presented. Theoretical analysis and simulation result of the proposed converter were verified.

scholarly journals A Quadratic Boost Converter with Voltage Multiplier Cell to Increase Voltage Gain

2021 ◽  
Vol 7 (03) ◽  
pp. 76-79
Author(s):  
P.Rangeela and Dr.A.RubyMeena
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Loop Control ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Integral Controller ◽  
Proportional Integral Controller

The high step up dc-dc converter with a quadratic boost converter with voltage multiplier cell (VM) to achieve a high voltage gain in the continuous conduction mode (CCM). To increase higher voltage gain, lower voltage stress on diodes and capacitors and requiring smaller inductors with reduced number of components. Quadratic Boost DC-DC converters are mainly used in applications like HEVs and EVs vehicles. The purpose of boost converter is to charge a low-voltage (12 V) battery during boost mode and to assist the high-voltage 200V battery. In this implementation, closed-loop control in high voltage side is implemented using PI (proportional integral) controller.

scholarly journals A Quadratic Boost Converter with Voltage Multiplier Cell to Increase Voltage Gain

2021 ◽  
Vol 7 (03) ◽  
pp. 76-79
Author(s):  
P.Rangeela and Dr.A.RubyMeena
Keyword(s):  
High Voltage ◽  
Low Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Loop Control ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Voltage Stress ◽  
Integral Controller ◽  
Proportional Integral Controller

The high step up dc-dc converter with a quadratic boost converter with voltage multiplier cell (VM) to achieve a high voltage gain in the continuous conduction mode (CCM). To increase higher voltage gain, lower voltage stress on diodes and capacitors and requiring smaller inductors with reduced number of components. Quadratic Boost DC-DC converters are mainly used in applications like HEVs and EVs vehicles. The purpose of boost converter is to charge a low-voltage (12 V) battery during boost mode and to assist the high-voltage 200V battery. In this implementation, closed-loop control in high voltage side is implemented using PI (proportional integral) controller

A High Step-up DC-DC Converter Based on the Voltage Lift Technique for Renewable Energy Applications

2021 ◽  
Vol 13 (19) ◽  
pp. 11059
Author(s):  
Shahrukh Khan ◽  
Arshad Mahmood ◽  
Mohammad Zaid ◽  
Mohd Tariq ◽  
Chang-Hua Lin ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Common Ground ◽  
Closed Loop ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain

High gain DC-DC converters are getting popular due to the increased use of renewable energy sources (RESs). Common ground between the input and output, low voltage stress across power switches and high voltage gain at lower duty ratios are desirable features required in any high gain DC-DC converter. DC-DC converters are widely used in DC microgrids to supply power to meet local demands. In this work, a high step-up DC-DC converter is proposed based on the voltage lift (VL) technique using a single power switch. The proposed converter has a voltage gain greater than a traditional boost converter (TBC) and Traditional quadratic boost converter (TQBC). The effect of inductor parasitic resistances on the voltage gain of the converter is discussed. The losses occurring in various components are calculated using PLECS software. To confirm the performance of the converter, a hardware prototype of 200 W is developed in the laboratory. The simulation and hardware results are presented to determine the performance of the converter in both open-loop and closed-loop conditions. In closed-loop operation, a PI controller is used to maintain a constant output voltage when the load or input voltage is changed.

A Nonisolated DC–DC Boost Converter With High Voltage Gain and Balanced Output Voltage

2014 ◽  
Vol 61 (12) ◽  
pp. 6739-6746 ◽  
Author(s):  
George Cajazeiras Silveira ◽  
Fernando Lessa Tofoli ◽  
Luiz Daniel Santos Bezerra ◽  
Rene Pastor Torrico-Bascope
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
High Voltage Gain

scholarly journals Conversor Doubler Output Coupled Inductor para Aplicações de Fontes Alternativas

2021 ◽  
Author(s):  
HENRIQUE JAHNKE HOCH ◽  
TIAGO MIGUEL KLEIN FAISTEL ◽  
ADEMIR TOEBE ◽  
ANTóNIO MANUEL SANTOS SPENCER ANDRADE
Keyword(s):  
High Voltage ◽  
Duty Cycle ◽  
Low Voltage ◽  
Energy Generation ◽  
Boost Converter ◽  
Voltage Gain ◽  
Switched Capacitors ◽  
Number Of Components ◽  
Photovoltaic Energy ◽  
High Voltage Gain

High step-up DC-DC converters are necessary in photovoltaic energy generation, due the low voltage of the panels source. This article propose the Doubler Output Coupled Inductor converter. This converter is based in boost converter and utilize switched capacitors and a coupled inductor to maximize the static voltage gain. The converter achieve a high voltage gain with low turns ratio in the coupled inductor and an acceptable duty cycle. Can highlight the converter utilize low number of components and have low voltage and current stresses in semiconductors. To validate and evaluate the operation of the converter a 200W prototype is simulated.

scholarly journals Quadratic Boost Converter

2021 ◽  
Vol 9 (VII) ◽  
pp. 2010-2014
Author(s):  
Mamidala Hemanth Reddy
Keyword(s):  
Output Voltage ◽  
Semiconductor Device ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Practical Utilization ◽  
Analysis And Design ◽  
Simulink Model ◽  
Grid Connection

The output voltage from the sustainable energy like photovoltaic (PV) arrays and fuel cells will be at less amount of level. This must be boost considerably for practical utilization or grid connection. A conventional boost converter will provides low voltage gain while Quadratic boost converter (QBC) provides high voltage gain. QBC is able to regulate the output voltage and the choice of second inductor can give its current as positive and whereas for boost increases in the voltage will not able to regulate the output voltage. It has low semiconductor device voltage stress and switch usage factor is high. Analysis and design modeling of Quadratic boost converter is proposed in this paper. A power with 50 W is developed with 18 V input voltage and yield 70 V output voltage and the outcomes are approved through recreation utilizing MATLAB/SIMULINK MODEL.

Sign in / Sign up

Export Citation Format

Share Document