scholarly journals Quadratic Boost Converter

2021 ◽  
Vol 9 (VII) ◽  
pp. 2010-2014
Author(s):  
Mamidala Hemanth Reddy
Keyword(s):  
Output Voltage ◽  
Semiconductor Device ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Gain ◽  
Practical Utilization ◽  
Analysis And Design ◽  
Simulink Model ◽  
Grid Connection

The output voltage from the sustainable energy like photovoltaic (PV) arrays and fuel cells will be at less amount of level. This must be boost considerably for practical utilization or grid connection. A conventional boost converter will provides low voltage gain while Quadratic boost converter (QBC) provides high voltage gain. QBC is able to regulate the output voltage and the choice of second inductor can give its current as positive and whereas for boost increases in the voltage will not able to regulate the output voltage. It has low semiconductor device voltage stress and switch usage factor is high. Analysis and design modeling of Quadratic boost converter is proposed in this paper. A power with 50 W is developed with 18 V input voltage and yield 70 V output voltage and the outcomes are approved through recreation utilizing MATLAB/SIMULINK MODEL.

A High Step-up DC-DC Converter Based on the Voltage Lift Technique for Renewable Energy Applications

2021 ◽  
Vol 13 (19) ◽  
pp. 11059
Author(s):  
Shahrukh Khan ◽  
Arshad Mahmood ◽  
Mohammad Zaid ◽  
Mohd Tariq ◽  
Chang-Hua Lin ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Common Ground ◽  
Closed Loop ◽  
Low Voltage ◽  
Renewable Energy Sources ◽  
Input Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Open Loop ◽  
Voltage Gain

High gain DC-DC converters are getting popular due to the increased use of renewable energy sources (RESs). Common ground between the input and output, low voltage stress across power switches and high voltage gain at lower duty ratios are desirable features required in any high gain DC-DC converter. DC-DC converters are widely used in DC microgrids to supply power to meet local demands. In this work, a high step-up DC-DC converter is proposed based on the voltage lift (VL) technique using a single power switch. The proposed converter has a voltage gain greater than a traditional boost converter (TBC) and Traditional quadratic boost converter (TQBC). The effect of inductor parasitic resistances on the voltage gain of the converter is discussed. The losses occurring in various components are calculated using PLECS software. To confirm the performance of the converter, a hardware prototype of 200 W is developed in the laboratory. The simulation and hardware results are presented to determine the performance of the converter in both open-loop and closed-loop conditions. In closed-loop operation, a PI controller is used to maintain a constant output voltage when the load or input voltage is changed.

scholarly journals Implementation of Buck-Boost Converter as Low Voltage Stabilizer at 15 V

2019 ◽  
Vol 9 (4) ◽  
pp. 2230
Author(s):  
Suwarno Suwarno ◽  
Tole Sutikno
Keyword(s):  
Power Electronics ◽  
Wind Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Stabilizer ◽  
Voltage Regulator ◽  
Output Current ◽  
Converter Design

<p>This paper presents the implementation of the buck-boost converter design which is a power electronics applications that can stabilize voltage, even though the input voltage changes. Regulator to stabilize the voltage using PWM pulse that triger pin 2 on XL6009. In this design of buck-boost converter is implemented using the XL6009, LM7815 and TIP2955. LM7815 as output voltage regulator at 15V with 1A output current, while TIP2955 is able to overcome output current up to 5A. When the LM7815 and TIP2955 are connected in parallel, the converter can increase the output current to 6A.. Testing is done using varied voltage sources that can be set. The results obtained from this design can be applied to PV (Photovoltaic) and WP (Wind Power), with changes in input voltage between 3-21V dc can produce output voltage 15V.</p>

scholarly journals Modified Multi Input Multilevel DC-DC Boost Converter for Hybrid Energy Systems

2020 ◽  
Vol 9 (4) ◽  
pp. 1067-1072
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Complex Structure ◽  
Energy Systems ◽  
Input Voltage ◽  
Boost Converter ◽  
Design Parameters ◽  
Hybrid Energy ◽  
Hybrid Energy Systems ◽  
Constant Output

DC-DC converters are playing an important role in designing of Electric Vehicles, integration of solar cells and other DC applications. Contemporary high power applications use multilevel converters that have multi stage outputs for integrating low voltage sources. Conventional DC-DC converters use single source and have complex structure while using for Hybrid Energy Systems. This paper proposes a multi-input, multi-output DC-DC converter to produce constant output voltage at different input voltage conditions. This topology is best suitable for hybrid power systems where the output voltage is variable due to environmental conditions. It reduces the requirement of magnetic components in the circuit and also reduces the switching losses. The proposed topology has two parts namely multi-input boost converter and level-balancing circuit. Boost converter increases the input voltage and Level Balancing Circuit produce Multi output. Equal values of capacitors are used in Level Balancing Circuit to ensure the constant output voltage at all output stages. The operating modes of each part are given and the design parameters of each part are calculated. Performance of the proposed topology is verified using MATLAB/Simulink simulation which shows the correctness of the analytical approach. Hardware is also presented to evaluate the simulation results.

scholarly journals A Voltage Multiplier Circuit Based Quadratic Boost Converter for Energy Storage Application

2020 ◽  
Vol 10 (22) ◽  
pp. 8254
Author(s):  
Javed Ahmad ◽  
Mohammad Zaid ◽  
Adil Sarwar ◽  
Chang-Hua Lin ◽  
Shafiq Ahmad ◽  
...  
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
High Gain ◽  
Boost Converter ◽  
Voltage Gain ◽  
Voltage Multiplier ◽  
High Voltage Gain ◽  
Power Application ◽  
High Output Voltage ◽  
Multiplier Circuit

In this paper, a new transformerless high voltage gain dc-dc converter is proposed for low and medium power application. The proposed converter has high quadratic gain and utilizes only two inductors to achieve this gain. It has two switches that are operated simultaneously, making control of the converter easy. The proposed converter’s output voltage gain is higher than the conventional quadratic boost converter and other recently proposed high gain quadratic converters. A voltage multiplier circuit (VMC) is integrated with the proposed converter, which significantly increases the converter’s output voltage. Apart from a high output voltage, the proposed converter has low voltage stress across switches and capacitors, which is a major advantage of the proposed topology. A hardware prototype of 200 W of the proposed converter is developed in the laboratory to validate the converter’s performance. The efficiency of the converter is obtained through PLECS software by incorporating the switching and conduction losses.

scholarly journals High gain multiphase boost converter based-on capacitor clamping structure

2021 ◽  
Vol 24 (2) ◽  
pp. 689
Author(s):  
Oday Saad Fares ◽  
Jasim Farhood Hussen
Keyword(s):  
High Voltage ◽  
Output Voltage ◽  
Low Voltage ◽  
High Gain ◽  
Industrial Applications ◽  
Boost Converter ◽  
Power Device ◽  
Voltage Gain ◽  
High Voltage Gain ◽  
And Performance

<p>In the last few years, the non-isolated dc converters involving high voltage gain with adequate performance are becoming quite popular in industrial applications. This is resulting in high voltage and current stress on the power device (switches and diodes), as well as a limited output voltage with a high duty cycle. This paper proposes a multi-phase non-isolated boost converter that uses capacitor clamping to increase output voltage while reducing stress across the power device. There are two stages in the proposed converter (first stage is three inductors and three switches and the second stage is clamper circuit of three capacitors and three diodes). The proposed converter is high voltage gain, with low voltage stress through switches transistors. To justify the theoretical analysis, the concept was validated through mathematical analysis and by simulation using MATLAB/SIMULINK. The results carried out the results permit the converter behavior and performance to be accurately.</p>

scholarly journals A Transformer less Buck Boost Converter with Positive Output Voltage

2021 ◽  
Vol 9 (VII) ◽  
pp. 3575-3580
Author(s):  
Lambu Rushi Reddy
Keyword(s):  
Output Voltage ◽  
Input Voltage ◽  
Industrial Applications ◽  
Boost Converter ◽  
Voltage Gain ◽  
High Voltage Gain ◽  
Duty Cycles ◽  
Power Switches ◽  
Constant Output ◽  
Step Down

Some industrial applications require high step-up and step-down voltage gain. The transformer less buck-boost converter has high voltage gain than that of traditional buck-boost converter without extreme duty cycles. A transformer less buck-boost converter with simple structure is obtained by inserting an additional switched network into the traditional buck-boost converter. The two power switches of the buck-boost converter operate synchronously. The operating principles of the buck-boost converter operating in continuous conduction modes are presented. A new buck- boost converter is presented by providing a feedback to the converter. By this, constant output voltage can be maintained under varying load conditions in both buck and boost operation. The output voltage of 40V (step—up mode)/8V (step down mode) is obtained with input voltage 18V and the outcomes are approved through recreation using PSIM MODEL.

scholarly journals Multistage DC-DC Step-Up Self Balanced and Magnetic Component Free Converter for Photovoltaic Applications—Hardware Implementation

2017 ◽  
Author(s):  
Mahajan Sagar Bhaskar ◽  
Sanjeevikumar Padmanaban ◽  
Frede Blaabjerg
Keyword(s):  
Output Voltage ◽  
Low Voltage ◽  
Input Voltage ◽  
Power Converter ◽  
Switching Frequency ◽  
Voltage Gain ◽  
Magnetic Components ◽  
Photovoltaic Applications ◽  
Control Switch ◽  
Converter Topology

This article presents a self balanced multistage DC-DC step-up converter for photovoltaic applications. Proposed converter topology is designed for unidirectional power transfer and provides a doable solution for photovoltaic applications where voltage is required to be stepped up without magnetic components (Transformer-less and Inductor-less). The output voltage obtained from renewable sources will be low and must be stepped up by using a DC-DC converter for photovoltaic applications. K diodes and K capacitors along with two semiconductor control switch are used in the K-stage proposed converter to obtain an output voltage which is (K+1) times the input voltage. The conspicuous features of proposed topology are i) Magnetic components free (Transformer-less and Inductor-less). ii) Continuous input current iii) Low voltage rating semiconductor devices and capacitors iv) Modularity v) Easy to add a higher number of levels to increase voltage gain vi) Only two control switches with alternating operation and simple control. The proposed converter is compared with recent existing transformer-less and Inductor-less power converter in term of voltage gain, number of devices and cost. The application of proposed circuit is discussed in detail. The proposed converter has been designed with rated power of 60W, input voltage is 24V, output voltage is 100V and switching frequency is 100 kHz. The performance of the converter is verified through experimental and simulation results.

A Step Down Transformerless Single Switch Integerated Buck and Buck-Boost Converter

2016 ◽  
Vol 5 (3) ◽  
pp. 144
Author(s):  
P. Maithili ◽  
C. Tharani ◽  
J. Nivedha ◽  
D. Soundarrajan
Keyword(s):  
Output Voltage ◽  
Closed Loop ◽  
High Efficiency ◽  
Control Structure ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Voltage Application ◽  
Constant Output ◽  
Efficient Power

This paper presents about the designing of the controller for integrated Buck Buck-Boost converter for maintaining the constant DC output voltage. This constant output voltage can be used for low voltage application. The absence of transformer includes the advantages of losses is less, efficient power factor and high efficiency. It provides the simple control structure with the positive constant output voltage .It operates on the closed loop with the designing of the PI controller for a MOSFET switch to provide the gate pulse. Whatever may be the input voltage it will produce the constant output voltage. The converter is successfully done by using MAT Lab/Simulink and verified the error reducing to negligible values.

scholarly journals Integrated buck and boost converter for a universal battery charger of an Electric Vehicle

2021 ◽  
Vol 309 ◽  
pp. 01073
Author(s):  
Sreekanth Reddy Kondreddy ◽  
B. Veeranna Sreenivasappa
Keyword(s):  
High Power ◽  
Output Voltage ◽  
Low Voltage ◽  
Harmonic Distortion ◽  
Input Voltage ◽  
Boost Converter ◽  
Battery Charger ◽  
High Power Factor ◽  
Wide Range ◽  
The Cost

A two-stage converter connects the input grid voltage to a pack of batteries with the voltage varying between 48-400 V, depending on the size and the range of the vehicle, with battery-operated electric and Plug-in Hybrid Electric Vehicles (PHEVs). This article offers a unique built-in converter that can interface with both high voltage (HV) and low voltage (LV) batteries. For all car architectures a universal charger that can accommodate this wide range of battery pack voltages is suitable. The novel integrated buck and boost converter (IBBC) is the proposed converter supplied using AC-DC driver at the front end mode. The main objective of this paper is to show a universal battery charger for an EV with a high power factor (PFC) and a small total harmonic distortion (THD) in addition to the high power density. A PFC converter is formed without any auxiliary circuit to balance the output voltage dependence of the battery against fluctuations in the ac grid input voltage, which in turn reduces the cost of additional circuit. A closed loop controller scheme is used to adjust for variations in the broad range output voltage and load. The proposed topology’s detailed operation is simulated using the MATLAB/Simulink software and achieved a THD of 1.18%.

scholarly journals A high efficiency non-inverting multi device buck-boost DC-DC converter with reduced ripple current and wide bandwidth for fuel cell low voltage applications

2018 ◽  
Vol 15 (2) ◽  
pp. 165-186
Author(s):  
Naik Venkatesh ◽  
Paulson Samuel
Keyword(s):  
Steady State ◽  
Fuel Cell ◽  
Output Voltage ◽  
High Efficiency ◽  
Low Voltage ◽  
Input Voltage ◽  
Boost Converter ◽  
Prototype Model ◽  
Voltage Range ◽  
Operating Modes

The voltage produced by the fuel cell (FC) device is unregulated and varies from 0.4 V to 0.8 V on full load to no-load respectively. When these devices are used in low voltage applications and output voltage lies between higher and lower values of input voltage range, it is required to connect a DCDC buck-boost converter to get a fixed output voltage. In this paper, a new noninverting multi device buck boost converter (MDBBC) is proposed, in which the multi device buck and boost converters are connected in cascade and operate individually either in buck or boost operating modes. The paper also includes the steady state analysis of MDDBC based on the state space averaging technique. A prototype model of proposed converter compatible with FCS-1000 Horizon FC model with rating of 270 W, 36 V is designed and developed. The proposed converter is experimentally validated with the results obtained from the prototype model, and results show the superiority of the converter with higher efficiency and lesser ripple current observed under steady state operation of the converter.

Sign in / Sign up

Export Citation Format

Share Document