scholarly journals Fischer-Tropsch Diesel and Biofuels Exergy and Energy Analysis for Low Emissions Vehicles

2021 ◽  
Vol 11 (13) ◽  
pp. 5958
Author(s):  
Felipe Andrade Torres ◽  
Omid Doustdar ◽  
Jose Martin Herreros ◽  
Runzhao Li ◽  
Robert Poku ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Alternative Fuels ◽  
Hybrid Electric Vehicles ◽  
Alternative Fuel ◽  
Biodiesel Fuel ◽  
Compression Ignition Engine ◽  
Fischer Tropsch ◽  
Fuel Blends ◽  
Exergetic Analysis ◽  
New Generation

This research investigates the effects of a synthetic diesel-like fuel (Fischer-Tropsch diesel) and biofuels (ethanol and biodiesel) fuel blends on the energy-exergy efficiencies and gaseous exhaust emissions characteristics of a compression ignition engine. Two blends of alternative fuels denoted as E15B35FTD50 (15% ethanol, 35% biodiesel, and 50% Fischer-Tropsch diesel) and E15B35D50 (15% ethanol, 35% biodiesel, and 50% diesel) were experimentally studied on a single-cylinder diesel engine and compared to diesel fuel. The results show that the energetic and the exergetic efficiencies of the alternative fuels are comparable to those of the engine fueled with diesel fuel. The unburnt HC, NO, N2O, and NH3 emissions were reduced for the two alternative fuel blends compared to diesel, while CO emissions increased. The light HC species were found to slightly increase for the alternative fuel blends in comparison with diesel fuel. However, the total HC was considerably reduced by the combustion of E15B35FTD50 not only when compared to the diesel fuel combustion, but also when compared to E15B35D50. Overall, these results may contribute to identifying advantages and limitations in terms of energetic-exergetic analysis and emissions for the new generation of conventional diesel and hybrid electric vehicles that aim to achieve future emissions regulations.

Comparisons of Emissions Characteristics of Several Turbine Engines Burning Fischer-Tropsch and Hydroprocessed Esters and Fatty Acids Alternative Jet Fuels

2012 ◽  
Author(s):  
Edwin Corporan ◽  
Matthew J. DeWitt ◽  
Christopher D. Klingshirn ◽  
David Anneken ◽  
Linda Shafer ◽  
...  
Keyword(s):  
Fatty Acids ◽  
Alternative Fuels ◽  
Particle Number ◽  
Alternative Fuel ◽  
Turbine Engines ◽  
Gaseous Emissions ◽  
Hazardous Air Pollutants ◽  
Fischer Tropsch ◽  
Fuel Blends ◽  
Engine Power

A summary of the impacts of alternative fuel blends on the gaseous and particulate matter (PM) (mostly soot) emissions of aircraft turbine engines is presented. Six engines were studied under several US Air Force and NASA sponsored programs to assess the impacts of the alternative (non-petroleum) fuels on emissions and/or to support the certification of military aircraft for the use of 50/50 (by volume) alternative fuel/JP-8 blends. One turboshaft (T63) and five turbofan (CFM56-7, CFM56-2, F117, TF33 and PW308) engines were studied. Fuels derived from coal and natural gas produced via Fischer-Tropsch (FT) synthesis, and fuels from animal fats and plant oils produced via hydroprocessing [Hydroprocessed Esters and Fatty Acids (HEFA)] were evaluated. Trends of alternative fuel impacts on emissions compared to conventional fuel for the different engine types are discussed. Results consistently show significant reductions in PM emissions with the alternative fuel blends compared to operation with conventional fuels. These relative reductions were observed to be lower as engine power increased. Engines operated with different alternative fuel blends were found to produce similar slopes of normalized particle number to engine power with only the magnitude of the reductions being a function of the fuel type. These results suggest that it may be plausible to predict particle number emissions from turbine engines operated on alternative fuels based on engine, engine setting, limited PM data and fuel composition. Gaseous emissions measurements show modest reductions of carbon monoxide, unburned hydrocarbons and hazardous air pollutants (HAPs) with the alternative fuels for several engines; however, no clear dependency of fuel impacts based on engine characteristics were observed.

Engine Performance with Diesel-Biodiesel Blends Fuel and Emission Characteristics

2020 ◽  
Vol 38 (5A) ◽  
pp. 779-788
Author(s):  
Marwa N. Kareem ◽  
Adel M. Salih
Keyword(s):  
Sulfur Content ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Esterification Reaction ◽  
Biodiesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
Hc Emissions

In this study, the sunflowers oil was utilized as for producing biodiesel via a chemical operation, which is called trans-esterification reaction. Iraqi diesel fuel suffers from high sulfur content, which makes it one of the worst fuels in the world. This study is an attempt to improve the fuel specifications by reducing the sulfur content of the addition of biodiesel fuel to diesel where this fuel is free of sulfur and has a thermal energy that approaches to diesel.20%, 30% and 50% of Biodiesel fuel were added to the conventional diesel. Performance tests and pollutants of a four-stroke single-cylinder diesel engine were performed. The results indicated that the brake thermal efficiency a decreased by (4%, 16%, and 22%) for the B20, B30 and B50, respectively. The increase in specific fuel consumption was (60%, 33%, and 11%) for the B50, B30, and B20 fuels, respectively for the used fuel blends compared to neat diesel fuel. The engine exhaust gas emissions measures manifested a decreased of CO and HC were CO decreased by (13%), (39%) and (52%), and the HC emissions were lower by (6.3%), (32%), and (46%) for B20, B30 and B50 respectively, compared to diesel fuel. The reduction of exhaust gas temperature was (7%), (14%), and (32%) for B20, B30 and B50 respectively. The NOx emission increased with the increase in biodiesel blends ratio. For B50, the raise was (29.5%) in comparison with diesel fuel while for B30 and B20, the raise in the emissions of NOx was (18%) and...

scholarly journals A Comparative Study of Biofuels and Fischer–Tropsch Diesel Blends on the Engine Combustion Performance for Reducing Exhaust Gaseous and Particulate Emissions

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1538
Author(s):  
Felipe Andrade Torres ◽  
Omid Doustdar ◽  
Jose Martin Herreros ◽  
Runzhao Li ◽  
Robert Poku ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Road Transport ◽  
Oxidation Catalyst ◽  
Transport Sector ◽  
Particulate Emissions ◽  
Gaseous Emissions ◽  
Fischer Tropsch ◽  
Engine Combustion

The worldwide consumption of fossil hydrocarbons in the road transport sector in 2020 corresponded to roughly half of the overall consumption. However, biofuels have been discreetly contributing to mitigate gaseous emissions and participating in sustainable development, and thus leading to the extending of the commercial utilization of internal combustion engines. In this scenario, the present work aims at exploring the effects of alternative fuels containing a blend of 15% ethanol and 35% biodiesel with a 50% fossil diesel (E15D50B35) or 50% Fischer–Tropsch (F-T) diesel (E15FTD50B35) on the engine combustion, exhaust emissions (CO, HC, and NOx), particulate emissions characteristics as well as the performance of an aftertreatment system of a common rail diesel engine. It was found that one of the blends (E15FTD50B35) showed more than 30% reduction in PM concentration number, more than 25% reduction in mean particle size, and more than 85% reduction in total PM mass with respect to conventional diesel fuel. Additionally, it was found that the E15FTD50B35 blend reduces gaseous emissions of total hydrocarbons (THC) by more than 25% and NO by 3.8%. The oxidation catalyst was effective in carbonaceous emissions reduction, despite the catalyst light-off being slightly delayed in comparison to diesel fuel blends.

Influence of Nano-Particle Additives on Bio-Diesel-Fuelled CI Engines

2021 ◽  
pp. 1424-1443
Author(s):  
Tamilvanan A. ◽  
K. Balamurugan ◽  
T. Mohanraj ◽  
P. Selvakumar ◽  
B. Ashok ◽  
...  
Keyword(s):  
Diesel Fuel ◽  
High Surface ◽  
High Surface Area ◽  
Combustion Process ◽  
Biodiesel Fuel ◽  
Emission Characteristics ◽  
Operating Pressure ◽  
Transfer Rates ◽  
Fuel Blends ◽  
Ci Engine

Biodiesel is proven to be the best substitute for petroleum-based conventional diesel fuel in existing engines with or without minor engine modifications. The performance characteristics of biodiesel as a fuel in CI engine are slightly lower than that of diesel fuel. The emission characteristics of biodiesel are better than diesel fuel except NOX emission. The thermo-physical properties of biodiesel are improved by suspending the nano metal particles in the biodiesel, which make them an observable choice for the use of nanoparticles-added fuels in CI engine. High surface area of nanoparticles that promotes higher operating pressure and heat transfer rates that further quicken the combustion process by providing better oxidation. Thus, it has been inferred that addition of nanoparticles as an additive to biodiesel fuel blends in diesel engines and its effects on performance, combustion, and emission characteristics are discussed in this chapter.

Compatibility of Palm Biodiesel Blends on the Existing Elastomer Fuel Hose in Diesel Engine with Approach of Dynamic Test Rig: A Concept Study

2020 ◽  
Vol 1010 ◽  
pp. 172-177
Author(s):  
Narisa Sa'at ◽  
Ariffin Samsuri ◽  
Noradila Abdul Latif ◽  
Nurul Fitriah Nasir ◽  
Rais Hanizam Madon ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Dynamic Testing ◽  
Dynamic Test ◽  
Field Trials ◽  
Biodiesel Fuel ◽  
Compatibility Study ◽  
Fuel System ◽  
Experimental Conditions

Elastomer is one of the important material for the hoses, sealants and tubes in the components of fuel delivery system in diesel engine vehicles due to the factor of compatibility with diesel fuel. However, concern were arise that presence of alcohol, fatty acid component and other factors such as water content in the alternative fuels which is blended biodiesel fuel and different chemical composition from the diesel fuel may increase further uncertainty to the consumer of diesel engine or diesel engine manufacturers in terms of compatibility issue. Thus this paper intends to assess current and typical test standards on their efficacy of representing the fuel system of diesel engine vehicles. Respectively, ASTM D471 are based on laboratory immersion studies and the experimental conditions are differ from the real service conditions in the fuel system of diesel engine vehicles. Even though number of previous studies regarding to the compatibility of elastomer components has been reported, there is a need to set up the exact material that present in the fuel system of diesel engine vehicles. This is especially right for elastomers since their resistance is mainly depends on their elemental compositions. As such, introduction of the dynamic testing approach that may be applied when assessing the compatibility study between blended biodiesel fuel that simulate the actual fuel system of a diesel engine vehicles before carrying out in the field trials.

Enhancing Diesel Engine Performance and Reducing Emissions Using Binary Biodiesel Fuel Blend

2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Paramvir Singh ◽  
S. R. Chauhan ◽  
Varun Goel ◽  
Ashwani K. Gupta
Keyword(s):  
Fuel Consumption ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Transport Sector ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Fuel Blend ◽  
Fuel Blends ◽  
Fuel Mixing ◽  
Ci Engines

Fossil fuel consumption provides a negative impact on the human health and environment in parallel with the decreased availability of this valuable natural resource for the future generations to use as a source of chemical energy for all applications in energy, power, and propulsion. The diesel fuel consumption in the transport sector is higher than the gasoline in most developing countries for reasons of cost and economy. Biodiesel fuel offers a good replacement for diesel fuel in compression ignition (CI) diesel engines. Earlier investigations by the authors revealed that a blend of 70% amla seed oil biodiesel and 30% eucalyptus oil (AB70EU30) is the favorable alternative renewable fuel blend that can be used as a fuel in diesel engines. With any fuel, air/fuel mixing and mixture preparation impact efficiency, emissions, and performance in CI engines. Minor adjustments in engine parameters to improve air/fuel mixing and combustion are deployable approaches to achieve good performance with alternative fuel blends in CI engines. This paper provides the role of a minor modification to engine parameters (compression ratio, injection timing, and injection pressure) on improved performance using the above mixture of binary fuel blends (AB70EU30). The results showed that the use of AB70EU30 in modified engine resulted in higher brake thermal efficiency and lower brake specific fuel consumption compared to normal diesel for improved combustion that also resulted in very low tailpipe emissions.

INVESTIGATION ON CHARACTERISTICS OF POME BLENDED DIESEL ENGINE

2015 ◽  
Vol 75 (8) ◽  
Author(s):  
Helmisyah Ahmad Jalaludin ◽  
Mohd Ruysdi Ramliy ◽  
Nik Rosli Abdullah ◽  
Salmiah Kasolang ◽  
Shahrir Abdullah ◽  
...  
Keyword(s):  
High Temperature ◽  
Combustion Chamber ◽  
Fuel Consumption ◽  
Oxygen Content ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Sudden Increase ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Complete Combustion

The sudden increase in fuel prices due to diminishing petroleum resources and the pollution resulting from its use has resulted in research into alternative fuels such as biodiesel. In addition, the faster combustion and high temperature in the combustion chamber which results from petroleum diesel fuel leads to higher nitrogen oxide (NOx) and Particulate Matter (PM) emissions. Therefore, this research was conducted to investigate the effect of using palm oil methyl ester (POME) blends as alternative fuels on the performance and emission of a compression ignition engine. The performance of POME blends and diesel were compared by manipulating the load of the engine at 1800 rpm. The results obtained show that fuel consumption rate is higher for the POME blends compared to the diesel fuel and increases as the POME concentration increases. The increment of brake specific fuel consumption and the reduction of CO emission exhibit a relation to the increase in percentage of POME. This is mainly contributed by the higher oxygen content of POME which promotes complete combustion of the blends. However, efficient combustion from the blends as compared to diesel fuel resulted from higher oxygen content and cetane number leads to significant increase in exhaust temperature. This in turn increases NOx emissions since using POME blends is highly related to high temperature of combustion chamber. The experimental results proved that POME in compression ignition engine is a possible substitute to diesel.

scholarly journals Development of the Premixing Injector in Burner System

2013 ◽  
Vol 465-466 ◽  
pp. 302-307 ◽  
Author(s):  
Mohamad Farid Sies ◽  
Norrizal Mustaffa ◽  
Hanis Zakaria ◽  
Hamidon bin Salleh ◽  
Bukhari Manshoor ◽  
...  
Keyword(s):  
Global Warming ◽  
Renewable Energy ◽  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuel ◽  
Biodiesel Fuel ◽  
Manufacturing Sectors

Today, global warming is the biggest issues due the increasing of emissions from diesel fuel in transportation and manufacturing sectors [1-. The solution for this issue is by using Biodiesel fuel as alternative fuel in both sectors. Malaysia government has introduced the Biodiesel (B5) in the diesel engine for transportations [3]. Biodiesel fuel (BDF) in alternative fuel and renewable energy but it has low quality of fuel and can reduce the performance compared to the diesel fuel (DF)[4-6].

scholarly journals Combustion characteristics of compression ignition engine fuelled with rapeseed oil–diesel fuel–n-butanol blends

2021 ◽  
Vol 76 ◽  
pp. 17
Author(s):  
Jakub Čedík ◽  
Martin Pexa ◽  
Bohuslav Peterka ◽  
Miroslav Müller ◽  
Michal Holubek ◽  
...  
Keyword(s):  
Vegetable Oils ◽  
Diesel Fuel ◽  
Rapeseed Oil ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Solid Particles ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blend ◽  
Fuel Blends

Liquid biofuels for compression ignition engines are often based on vegetable oils. In order to be used in compression ignition engine the vegetable oils have to be processed because of their high viscosity or it is also possible to use vegetable oils in fuel blends. In order to decrease the viscosity of the fuel blends containing crude vegetable oil the alcohol-based fuel admixtures can be used. The paper describes the effect of rapeseed oil–diesel fuel–n-butanol blends on combustion characteristics and solid particles production of turbocharged compression ignition engine. The 10% and 20% concentrations of n-butanol in the fuel blend were measured and analysed. The engine Zetor 1204, located in tractor Zetor Forterra 8641 with the power of 60kW and direct injection was used for the measurement. The engine was loaded through power take off shaft of the tractor using mobile dynamometer MAHA ZW500. The measurement was carried out in stabilized conditions at 20%, 60% and 100% engine load. The engine speed was kept at 1950 rpm. Tested fuel blends showed lower production of solid particles than diesel fuel and lower peak cylinder pressure and with increasing concentration of n-butanol in the fuel blend the ignition delay was prolonged and premixed phase of combustion was increased.

Sign in / Sign up

Export Citation Format

Share Document