scholarly journals Effect of Bentonite Content and Hydration Time on Mechanical Properties of Sand–Bentonite Mixture

2021 ◽  
Vol 11 (24) ◽  
pp. 12001
Author(s):  
Yue Qin ◽  
Dongsheng Xu ◽  
Borana Lalit
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Model Parameters ◽  
Hydration Time ◽  
Static Properties ◽  
Bentonite Slurry ◽  
Contact Force Distribution

The bentonite is commonly used mixed with soils for groundwater retention and waste contaminant facilities. The incorporation of bentonite could significantly reduce hydraulic conductivity. In this study, the effects of bentonite content, hydration time and effective confining pressure on the static properties of a sand–bentonite mixture were studied using experimental and numerical methods. Firstly, a large number of drainage static triaxial tests on the sand–bentonite mixture with various bentonite contents were conducted. The test results show that the increase in bentonite content and hydration time leads to a slight decrease in shear strength and initial tangent modulus of the sand–bentonite mixture. The presence of bentonite reduces the shear shrinkage and dilatancy trend of the mixture. The cohesion of the mixture increases with the increase in bentonite content and hydration time, but the internal friction angle decreases correspondingly. The hydration of bentonite on the surface of sand particles changes the contact form between particles. The bentonite slurry between pores of the sand skeleton also affects the mechanical behavior of the sand–bentonite mixture. Then, a series of 3D discrete element models were established for numerical simulations of drainage static triaxial tests. The numerical model parameters were calibrated by experimental results. The meso-mechanism of bentonite content affecting the mechanical behavior was revealed according to the contact force distribution between particles. The research results are helpful to understand further the mechanism of bentonite on the mechanical properties of the sand–bentonite mixture.

scholarly journals Experimental Study of Stress-Seepage Coupling Properties of Sandstone under Different Loading Paths

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-21
Author(s):  
Xi Chen ◽  
Wei Wang ◽  
Yajun Cao ◽  
Qizhi Zhu ◽  
Weiya Xu ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Pore Pressure ◽  
Complex Loading ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Compression Tests ◽  
Biot Coefficient ◽  
Cyclic Loading And Unloading ◽  
Loading And Unloading

The study on hydromechanical coupling properties of rocks is of great importance for rock engineering. It is closely related to the stability analysis of structures in rocks under seepage condition. In this study, a series of conventional triaxial tests under drained condition and hydrostatic compression tests under drained or undrained condition on sandstones were conducted. Moreover, complex cyclic loading and unloading tests were also carried out. Based on the experimental results, the following conclusions were obtained. For conventional triaxial tests, the elastic modulus, peak strength, crack initiation stress, and expansion stress increase with increased confining pressure. Pore pressure weakened the effect of the confining pressure under drained condition, which led to a decline in rock mechanical properties. It appeared that cohesion was more sensitive to pore pressure than to the internal friction angle. For complex loading and unloading cyclic tests, in deviatoric stress loading and unloading cycles, elastic modulus increased obviously in first loading stage and increased slowly in next stages. In confining pressure loading and unloading cycles, the Biot coefficient decreased first and then increased, which indicates that damage has a great impact on the Biot coefficient.

scholarly journals Physical and Mechanical Properties of a Bulk Lightweight Concrete with Expanded Polystyrene (EPS) Beads and Soft Marine Clay

Materials ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1662 ◽  
Author(s):  
Jianguo Wang ◽  
Bowen Hu ◽  
Jia Hwei Soon
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Cement Content ◽  
Mass Density ◽  
Physical And Mechanical Properties ◽  
Confining Pressure ◽  
Expanded Polystyrene ◽  
Triaxial Tests ◽  
Filling Material ◽  
Confining Pressures

The variation of physical and mechanical properties of the lightweight bulk filling material with cement and expanded polystyrene (EPS) beads contents under different confining pressures is important to construction and geotechnical applications. In this study, a lightweight bulk filling material was firstly fabricated with Singapore marine clay, ordinary Portland cement and EPS. Then, the influences of EPS beads content, cement content, curing time and confining pressure on the mass density, stress–strain behavior and compressive strength of this lightweight bulk filling material were investigated by unconsolidated and undrained (UU) triaxial tests. In these tests, the mass ratios of EPS beads to dry clay (E/S) were 0%, 0.5%, 1%, 2%, and 4% and the mass ratios of cement to dry clay (C/S) were 10% and 15%. Thirdly, a series of UU triaxial tests were performed at a confining pressure of 0 kPa, 50 kPa, 100 kPa, and 150 kPa after three curing days, seven curing days, and 28 curing days. The results show that the mass density of this lightweight bulk filling material was mainly controlled by the E/S ratio. Its mass density decreased by 55.6% for the C/S ratio 10% and 54.9% for the C/S ratio 15% when the E/S ratio increased from 0% to 4% after three curing days. Shear failure more easily occurred in the specimens with higher cement content and lower confining pressure. The relationships between compressive strength and mass density or failure strain could be quantified by the power function. Increasing cement content and reducing EPS beads content will increase mass density and compressive strength of this lightweight bulk filling material. The compressive strength with curing time can be expressed by a logarithmic function with fitting correlation coefficient ranging from 0.83 to 0.97 for five confining pressures. These empirical formulae will be useful for the estimation of physical and mechanical properties of lightweight concretes in engineering application.

The Choice of Basic Pillar Design Theory for Locked Sand Condition

2012 ◽  
Vol 256-259 ◽  
pp. 354-357
Author(s):  
Zi Wei Ding ◽  
Amirhossein Bagherieh ◽  
Rui Min Feng ◽  
Xing Xing Wen
Keyword(s):  
Design Theory ◽  
Design Method ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Pillar Design ◽  
Design Theories ◽  
Locked Sand ◽  
Unconfined Strength ◽  
Very High

Because of unique properties of locked sand (very high friction angle and very low cohesion), a new pillar design method based on present basic pillar design theories must be developed. Wilson theory puts its focus on confining pressure, which is related to friction angle and cohesion. Triaxial tests results show that locked sand at Pattison mine has an average friction angle of 57°, which means the strength of the material increases rapidly with the confining pressure, and average cohesion of 2.6 MPa. Results show that choosing Wilson theory as basic pillar design theory not only considers the high friction angle of locked sand, but also minimizes the effects of Wilson’s hypothesis of neglecting the unconfined strength.

scholarly journals Contribution of Collagen Fiber Undulation to Regional Biomechanical Properties Along Porcine Thoracic Aorta

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Shahrokh Zeinali-Davarani ◽  
Yunjie Wang ◽  
Ming-Jay Chow ◽  
Raphaël Turcotte ◽  
Yanhang Zhang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Thoracic Aorta ◽  
Aortic Wall ◽  
Multiphoton Microscopy ◽  
Constitutive Models ◽  
Tensile Tests ◽  
Biomechanical Properties ◽  
Model Parameters ◽  
Extracellular Matrix Components

As major extracellular matrix components, elastin, and collagen play crucial roles in regulating the mechanical properties of the aortic wall and, thus, the normal cardiovascular function. The mechanical properties of aorta, known to vary with age and multitude of diseases as well as the proximity to the heart, have been attributed to the variations in the content and architecture of wall constituents. This study is focused on the role of layer-specific collagen undulation in the variation of mechanical properties along the porcine descending thoracic aorta. Planar biaxial tensile tests are performed to characterize the hyperelastic anisotropic mechanical behavior of tissues dissected from four locations along the thoracic aorta. Multiphoton microscopy is used to image the associated regional microstructure. Exponential-based and recruitment-based constitutive models are used to account for the observed mechanical behavior while considering the aortic wall as a composite of two layers with independent properties. An elevated stiffness is observed in distal regions compared to proximal regions of thoracic aorta, consistent with sharper and earlier collagen recruitment estimated for medial and adventitial layers in the models. Multiphoton images further support our prediction that higher stiffness in distal regions is associated with less undulation in collagen fibers. Recruitment-based models further reveal that regardless of the location, collagen in the media is recruited from the onset of stretching, whereas adventitial collagen starts to engage with a delay. A parameter sensitivity analysis is performed to discriminate between the models in terms of the confidence in the estimated model parameters.

Mechanical Properties of Rocks Used for the Construction of Vehicular Bridges Supported by Pier Masonry

2012 ◽  
Vol 535-537 ◽  
pp. 1881-1888 ◽  
Author(s):  
Gustavo Mendoza-Chavez ◽  
Luis Horacio Martínez-Mártinez ◽  
David Joaquin Delgado-Hernandez ◽  
David De León Escobedo ◽  
Elia Mercedes Alonso Guzmán ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Risk Assessment ◽  
Mechanical Behavior ◽  
Poisson Ratio ◽  
Friction Angle ◽  
Masonry Structure ◽  
Stone Masonry ◽  
Wide Availability ◽  
Density Values ◽  
Ongoing Project

In Mexico, since the early stages of the civilization, the stone masonry has assumed an important role in construction due to the wide availability of this kind of material. Masonry is a material composed by bricks, carved or even rubble stones jointed without (dry joint) or with mortar (mortar joints); which is principally formed with sand, water and cementitiuos materials. The research presented in this paper deals with the procedure of obtaining the mechanical properties of rocks placed on piers of four vehicular bridges located in the south of the state of Mexico, these mechanical properties are compressive strength, modulus of elasticity, Poisson ratio, Cohesion and Internal friction Angle of the rocks as independent units, also are reported the Density values. All of these properties are necessary to conduct further research regarding the mechanical behavior of the pier as a structure since this piece of research is part of an ongoing project concerning risk assessment of vehicular bridges developed in Mexico. The identified rocks in masonry were volcanic igneous materials such as dacites, basalts, rhyolites, andesites and rusted andesites. The materials with the highest and the lowest mechanical properties are the basalt and the dacite respectively. It is recommended to use the dacite’s properties in order to perform a conservative analysis of the mechanical behavior of any masonry structure, located near the selected sample studied herein.

scholarly journals Experimental study on the thermal damage characteristics of cement stone

2020 ◽  
pp. 317-317
Author(s):  
Feng Xu ◽  
Bowen Qian ◽  
Ling Tan ◽  
Jianqiang Xu ◽  
Shengchuan Tang ◽  
...  
Keyword(s):  
Strain Curve ◽  
Horizontal Wells ◽  
Friction Angle ◽  
Confining Pressure ◽  
Triaxial Tests ◽  
Cement Stone ◽  
Different Temperatures ◽  
Confining Pressures ◽  
Southwest Region ◽  
Sealing Failure

Aiming at the problem of cement ring sealing failure during deep high-temperature shale gas exploitation, comprehensively considering the influence of the characteristics of multi-cluster fracturing of multiple horizontal wells and formation temperature, the cementing cement the southwest region is taken as the research object. After exposure to different temperatures (95?C and 135?C) and for different times (5, 10 and 20 times), axial and triaxial tests with different confining pressures (0, 5 MPa, 15 MPa and 30 MPa) were carried out. The research shows that: (1) the stress-strain curve of cement stone after heat treatment can be divided into four stages: compaction, elastic, yield and post-peak stage. As the confining pressure increases, the compaction phase disappears, the yield phase increases, and we see the transition from brittle to ideal plasticity after the peak; (2) as the temperature and number of thermal cycles increase, the cohesive force decreases significantly, and the internal friction angle shows a slight increase. The elastic modulus and the peak strength decreased.

scholarly journals The Influence of Kaolinite - Illite toward mechanical properties of Claystone

2019 ◽  
Vol 11 (1) ◽  
pp. 440-446
Author(s):  
Supandi Supandi ◽  
Zufialdi Zakaria ◽  
Emi Sukiyah ◽  
Adjat Sudradjat
Keyword(s):  
Mechanical Properties ◽  
Physical Properties ◽  
Void Ratio ◽  
Correlation Coefficients ◽  
Physical And Mechanical Properties ◽  
Friction Angle ◽  
Engineering Properties ◽  
Rock Properties ◽  
Triaxial Tests ◽  
Mineralogical Characteristics

Abstract This study investigates the relationship between clay minerals (kaolinite and illite) and rock properties of the claystone, including both mechanical (cohesion, friction angle, stress, and strain) and physical properties (natural water content, void ratio, and wet density), belonging to Warukin Formation of Kalimantan, Indonesia. Mineralogical characteristics of these rocks were studied using petrological and X-ray diffraction techniques, whereas the mechanical and physical properties were tested by conducting uniaxial and triaxial tests. Relationship among the variables was determined using correlation coefficients. It was observed that the mineralogy of the rocks pose strong constraints on their engineering properties. The results showed that an increase in illite content decreases cohesion, friction angle, strength, and safety factor; and increases natural moisture content, void ratio, and wet density. Although illite content of these rocks was just about 10.8% of the total minerals, it has significantly contributed to the modification of physical and mechanical properties. In contrast, kaolinite did not have a significant impact; since the correlation between various parameters was significantly low (correlation coefficient was much less, <0.3). Therefore while selecting the materials for geotechnical engineering applications, illite emerges as a safer alternative to kaolinite, especially when its concentration is less than 10.8% of the total rock mass.

scholarly journals Experimental Investigation on Failure Modes and Mechanical Properties of Rock-Like Specimens with a Grout-Infilled Flaw under Triaxial Compression

2019 ◽  
Vol 2019 ◽  
pp. 1-14
Author(s):  
Huilin Le ◽  
Shaorui Sun ◽  
Feng Zhu ◽  
Haotian Fan
Keyword(s):  
Mechanical Properties ◽  
Rock Mass ◽  
Epoxy Resin ◽  
Failure Modes ◽  
Shear Failure ◽  
Fractured Rock ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Compression Tests

Flaws existing in rock mass are one of the main factors resulting in the instability of rock mass. Epoxy resin is often used to reinforce fractured rock mass. However, few researches focused on mechanical properties of the specimens with a resin-infilled flaw under triaxial compression. Therefore, in this research, epoxy resin was selected as the grouting material, and triaxial compression tests were conducted on the rock-like specimens with a grout-infilled flaw having different geometries. This study draws some new conclusions. The high confining pressure suppresses the generation of tensile cracks, and the failure mode changes from tensile-shear failure to shear failure as the confining pressure increases. Grouting with epoxy resin leads to the improvement of peak strengths of the specimens under triaxial compression. The reinforcement effect of epoxy resin is better for the specimens having a large flaw length and those under a relatively low confining pressure. Grouting with epoxy resin reduces the internal friction angle of the samples but improves their cohesion. This research may provide some useful insights for understanding the mechanical behaviors of grouted rock masses.

scholarly journals Triaxial Test and Mechanical Analysis of Rock-Soil Aggregate Sampled from Natural Sliding Mass

2015 ◽  
Vol 2015 ◽  
pp. 1-14 ◽  
Author(s):  
Shuling Huang ◽  
Xiuli Ding ◽  
Yuting Zhang ◽  
Wei Cheng
Keyword(s):  
Mechanical Behavior ◽  
Large Scale ◽  
Mechanical Response ◽  
Strain Curve ◽  
Friction Angle ◽  
Mechanical Analysis ◽  
Soil Aggregate ◽  
Hydropower Plant ◽  
Triaxial Tests ◽  
Confining Pressures

Rock-soil aggregate, as a specific geomaterial, exhibits complicated mechanical behavior. The rock-soil aggregate sampled from the deep layer of sliding mass at Jinpingzi area of Wudongde hydropower plant on Yangtze River is investigated to understand its mechanical behavior. Large-scale laboratory triaxial tests are conducted considering different gradations, stone contents and confining pressures. The results show that variation of stone content and gradation considerably affects the mechanical characteristics of rock-soil aggregate. Further, the influences of stone content, and gradation variation on stress-strain curve, Mohr-Coulomb criterion based shear strength parameters, Duncan-Chang model based deformation parameters, and internal friction angle are analyzed. A modified Rowe’s stress-dilatancy equation describing the mechanical response of rock-soil aggregate is then suggested.

Study on the Deformation and Strength Characteristics of Geotechnical Grille Reinforced Sand-Gravel under Low Confining Pressure

2011 ◽  
Vol 250-253 ◽  
pp. 2632-2639
Author(s):  
Bin Xu ◽  
De Gao Zou ◽  
Jing Bi ◽  
Xian Jing Kong ◽  
Tao Gong
Keyword(s):  
Residual Strength ◽  
Large Scale ◽  
Volumetric Strain ◽  
Friction Angle ◽  
Confining Pressure ◽  
Peak Strength ◽  
Strength Characteristics ◽  
Triaxial Tests ◽  
Reinforced Sand ◽  
Deformation And Strength Characteristics

A series of large scale consolidated drained shear triaxial tests were performed on reinforced and unreinforced sand-gravel specimens, the peak strength and residual strength characteristics of reinforced and unreinforced sand-gravel specimens were compared. The results show that: the peak strength, the residual strength and cohesion of reinforced sand-gravel are higher than unreinforced specimens, and is related to the characteristics of geotechnical grille used in this study. However, adding geotechnical grille has less effect on maximum volumetric strain and internal friction angle of sand-gravel.

Sign in / Sign up

Export Citation Format

Share Document