scholarly journals Development of Pant-Type Harness with Fabric Air-Pocket for Pain Relief

2019 ◽  
Vol 9 (9) ◽  
pp. 1921
Author(s):  
Dongwoo Nam ◽  
Miyeon Kwon ◽  
Juhea Kim ◽  
Bummo Ahn

Harnesses can be used in various applications, such as entertainment, rescue operations, and medical applications. Because users are supported on the harness for a long time, they should feel comfortable wearing the harnesses. However, existing commercial harnesses are uncomfortable to wear and cause continuous serious pain. Therefore, in this study, a new pant-type harness with a fabric air pocket to reduce the applied pressure on the body, especially in the groin, is proposed. Keeping this in mind, we have designed and developed the pant-type harness. In addition, we performed pressure and contact area measurement experiments using the harness developed, pressure sensor, and a human mannequin. Peak and mean pressures and contact areas near the groin and waist were measured in the experiments. From the results, when air is injected in the air pockets, the peak pressure and contact area near the waist increased, and the peak pressure near the groin decreased. This means that the pressure applied on the human mannequin near the groin reduces because of the increased contact area near the waist, which is achieved by multi-layered air pockets. In this study, we proposed the optimal design of a novel pant-type harness that can address the limitations of existing harnesses. The proposed harness can be used for a prolonged time in applications, such as virtual reality entertainment, rescue operations, and rehabilitation.

2018 ◽  
Vol 3 (3) ◽  
pp. 2473011418S0030
Author(s):  
L. Daniel Latt ◽  
Alfonso Ayala ◽  
Samuel Kim ◽  
Jesus Lopez

Category: Ankle Introduction/Purpose: Increased tibiotalar peak pressure (PP) and decreased contact area (CA) following ankle fracture are associated with the development of post-traumatic osteoarthtritis. Lateral talar translation of just 1 mm has been shown to decrease CA by 42%. The impact of talar malalignment in other directions on ankle joint contact pressures (AJCP) are not well understood. The majority of research on AJCP has utilized cadaveric models in which body weight is simulated with an axial load applied through the tibia. This model does not account for Achilles tendon - which transmits the largest tendon force in the body during weight bearing. This study aimed to determine the effects of Achilles tendon loading on tibiotalar CA and PP in an axially loaded cadaver model at different ankle flexion angles. Methods: Ten fresh frozen cadaveric lower extremity specimens transected mid-tibia were dissected free of soft tissues surrounding the ankle, sparing the ligaments. The proximal tibia and fibula were potted in quick drying cement for rigid mounting on a MTS machine. A pressure sensing element (TekScan KScan model 5033) was inserted into the tibiotalar joint and used to measure CA (cm2) and PP (MPa). An axial load of 686 N was applied through the tibia and fibula, followed by a 350 N load via the Achilles tendon to simulate mid-stance conditions. Measurements were taken at neutral position, 15 degrees of dorsiflexion and 15 degrees of plantarflexion, with and without Achilles load. The effects of Achilles load and ankle flexion angle on CA and PP were analyzed using a 2x3 ANOVA. Bonferroni post-hoc adjustments were used for multiple comparisons. Level of statistical significance was set at p < 0.05. Results: ANOVA revealed significant main effects of ankle flexion on contact area and peak pressures (Table 1). Contact area was significantly lower for 15 degrees of plantarflexion than neutral and 15 degrees of dorsiflexion (p < 0.001). In addition, peak pressure was significantly higher for 15 degrees of plantarflexion than neutral and 15 degrees of dorsiflexion. ANOVA also indicated that contact area and peak pressure were significantly higher with Achilles load than without (p < 0.001). No interaction effects were found. Conclusion: The applied Achilles tendon load significantly altered tibiotalar PP in an axially loaded cadaver model. On the other hand, changes in CA with Achilles load were found to be minimal (~1.8%). We also found that the greatest PP and smallest CA occured during plantar flexion. This observation can be explained by a difference in width between the anterior and posterior talus. While the results of this study demonstrate the importance of Achilles tendon load on tibiotalar measurements, further studies investigating the effects of additional factors such as loading techniques are warranted to improve the physiological accuracy of cadaver models.


2018 ◽  
Vol 77 (10) ◽  
pp. 2528-2536 ◽  
Author(s):  
Lin Li ◽  
David Z. Zhu

Abstract In urban drainage systems, a sudden increase in the flow rate can cause the transition of the flow from open channel to pipe flow, and the entrapment of large air pockets in sewers, which might result in serious geysers and water-hammer like pressure events. This paper presents a numerical analysis of flow processes associated with the pressurization and release of an air pocket in order to study its influence on transient pressure in a horizontal pipe with an end orifice. The influence of the air pocket inside the pipe on the peak pressure can be described in two distinct regimes. In regime I for the pipe with a small orifice, the peak pressure is modulated by the pressurization and expansion of the air pocket and its subsequent damping. In regime II for the pipe with a large orifice, air can be quickly expelled, and the water column directly impinges on the pipe end wall and causes water-hammer like pressure. With the increase of the orifice size, the peak pressure decreases due to the change in the water velocity. In the study cases, the peak pressure in regime I is about two times the inlet pressure, while it can be more than forty times in regime II.


2020 ◽  
Vol 5 (4) ◽  
pp. 2473011420S0025
Author(s):  
Zhao Hong-Mou

Category: Ankle; Basic Sciences/Biologics Introduction/Purpose: To study the effect of different degrees of distal tibial varus and valgus deformities on the tibiotalar joint contact, and to understand the role of fibular osteotomy. Methods: Eight cadaveric lower legs were used for biomechanical study. Nine conditions were included: normal ankle joint (group A), 10° varus (group B), 5° varus (group C), 5° valgus (group D), 10° valgus (group E) with fibular preserved, and 10° varus (group F), 5° varus (group G), 5° valgus (group H), and 10° valgus (group I) after fibular osteotomy. The joint contact area, contact pressure, and peak pressure were tested; and the translation of contact force center was observed. Results: The joint contact area, contact pressure, and peak pressure had no significant difference between group A and groups B to E (P>0.05). After fibular osteotomy, the contact area decreased significantly in groups F and I when compared with group A (P<0.05); the contact pressure increased significantly in groups F, H, and I when compared with group A (P<0.05); the peak pressure increased significantly in groups F and I when compared with group A (P<0.05). There were two main anterior-lateral and anterior-medial contact centers in normal tibiotalar joint, respectively; and the force center was in anterior-lateral part, just near the center of tibiotalar joint. While the fibula was preserved, the force center transferred laterally with increased varus angles; and the force center transferred medially with increased valgus angles. However, the force center transferred oppositely to the medial part with increased varus angles, and laterally with increased valgus angles after fibular osteotomy. Conclusion: Fibular osteotomy facilitates the tibiotalar contact pressure translation, and is helpful for ankle joint realignment in suitable cases.


Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 963
Author(s):  
Ekaterina S. Dolinina ◽  
Elena V. Parfenyuk

Powerful antioxidant α-lipoic acid (LA) exhibits limited therapeutic efficiency due to its pharmacokinetic properties. Therefore, the purpose of this work was to evaluate the ability of silica-based composites of LA as well as its amide (lipoamide, LM), as new oral drug formulations, to control their release and maintain their therapeutic concentration and antioxidant activity in the body over a long time. The composites synthesized at different sol–gel synthesis pH and based on silica matrixes with various surface chemistry were investigated. The release behavior of the composites in media mimicking pH of digestive fluids (pH 1.6, 6.8, and 7.4) was revealed. The effects of chemical structure of the antioxidants, synthesis pH, surface chemistry of the silica matrixes in the composites as well as the pH of release medium on kinetic parameters of the drug release and mechanisms of the process were discussed. The comparative analysis of the obtained data allowed the determination of the most promising composites. Using these composites, modeling of the release process of the antioxidants in accordance with transit conditions of the drugs in stomach, proximal, and distal parts of small intestine and colon was carried out. The composites exhibited the release close to the zero order kinetics and maintained the therapeutic concentration of the drugs and antioxidant effect in all parts of the intestine for up to 24 h. The obtained results showed that encapsulation of LA and LM in the silica matrixes is a promising way to improve their bioavailability and antioxidant activity.


Biomolecules ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 79
Author(s):  
Svetlana N. Morozkina ◽  
Thi Hong Nhung Vu ◽  
Yuliya E. Generalova ◽  
Petr P. Snetkov ◽  
Mayya V. Uspenskaya

For a long time, the pharmaceutical industry focused on natural biologically active molecules due to their unique properties, availability and significantly less side-effects. Mangiferin is a naturally occurring C-glucosylxantone that has substantial potential for the treatment of various diseases thanks to its numerous biological activities. Many research studies have proven that mangiferin possesses antioxidant, anti-infection, anti-cancer, anti-diabetic, cardiovascular, neuroprotective properties and it also increases immunity. It is especially important that it has no toxicity. However, mangiferin is not being currently applied to clinical use because its oral bioavailability as well as its absorption in the body are too low. To improve the solubility, enhance the biological action and bioavailability, mangiferin integrated polymer systems have been developed. In this paper, we review molecular mechanisms of anti-cancer action as well as a number of designed polymer-mangiferin systems. Taking together, mangiferin is a very promising anti-cancer molecule with excellent properties and the absence of toxicity.


1894 ◽  
Vol 54 (326-330) ◽  
pp. 53-57 ◽  

For a long time I have adopted a process for separating the glycogen of the liver consisting in boiling with potash, pouring into alcohol, and collecting the precipitate. For the purpose of estimation, the precipitated glycogen was converted by means of sulphuric acid into glucose, the determination of which gave the information required. I afterwards applied the process to blood, and the various organs and tissues of the body, with the result that a more or less notable amount of cupric oxide reducing product was obtained, which I at the time looked upon as taking origin, as in the case of the liver, from glycogen.


2021 ◽  
Vol 100 (2) ◽  
pp. 254-261
Author(s):  
O.G. Sukhovjova ◽  
◽  
I.A. Ivanova ◽  
N.A. Kalugina ◽  
E.S. Zholobova ◽  
...  

The purpose of this publication is to describe the CANDLE syndrome (its etiology, pathogenesis, clinical manifestations) and present a clinical observation. CANDLE syndrome is a rare genetically inherited disease caused by impaired assembly by of the protease, which leads to the accumulation of abnormal (ubiquitinated) proteins in B-lymphocytes, fibroblasts, macrophages and some other cells of the body. As a result, an excessive activation of interferon synthesis occurs and a systemic inflammatory reaction develops with symptoms such as febrile fever, skin syndrome, represented by nodules and maculopapular rash, hepatosplenomegaly, lipodystrophy, amyotrophy, delayed physical development, as well as high laboratory activity. The article describes a clinical observation of a female patient with typical symptoms of CANDLE syndrome. However, due to the rarity of the disease and lack of publications describing it, it has not been possible to diagnose the child for a long time.


2020 ◽  
Vol 11 (SPL1) ◽  
pp. 1655-1661
Author(s):  
Roshna Sukheoji Bhutada ◽  
Kritika Umate

The need of the day is a brisk lift to the resistant framework to keep it fit, battling today pandemic infections, for example, Covid — 19. One should get the right amount of nutrients from the diet, supplementation regimen to boost the immune system. These spices are always there to make tasty food as well as to protect the body from infectious diseases by building the immunity strong Ayurveda approaches to develop physiological reactions to facilitate immunity. Planning of diet is most important to boost immunity. As per many types of research to provide supplementary food which contains Zinc, Vitamin C, Vitamin D and immunity boosting food such as dealing with plenty of spices for a very long time. These spices include some rare to very common spices which we can found near us. The concern is that these viral infections are very prone to attack weak immunity and take the chance to affect the country to the globe. So the very common spices available will be always helpful to get through this Regular use of a few spices in the very simple form proves its importance as a medicine. In this article a review of spices is done which we are available near us, we are using it in our daily life and we are getting the benefit of these which a common people might not be fully aware of about role of immunity building of the body. 


2020 ◽  
Vol 7 (2) ◽  
pp. 411-430
Author(s):  
Maja Tabea Jerrentrup

Abstract The art of bodypainting that is fairly unknown to a wider public turns the body into a canvas - it is a frequently used phrase in the field of bodypainting that illustrates the challenge it faces: it uses a three-dimensional surface and has to cope with its irregularities, but also with the model’s abilities and characteristics. This paper looks at individuals who are turned into art by bodypainting. Although body painting can be very challenging for them - they have to expose their bodies and to stand still for a long time while getting transformed - models report that they enjoy both the process and the result, even if they are not confident about their own bodies. Among the reasons there are physical aspects like the sensual enjoyment, but also the feeling of being part of something artistic. This is enhanced and preserved through double staging - becoming a threedimentional work of art and then being staged for photography or film clips. This process gives the model the chance to experience their own body in a detached way. On the one hand, bodypainting closely relates to the body and on the other hand, it can help to over-come the body.


1977 ◽  
Vol 42 (3) ◽  
pp. 362-367 ◽  
Author(s):  
R. Hagan ◽  
A. C. Bryan ◽  
M. H. Bryan ◽  
G. Gulston

We have studied two groups of eight preterm infants, relating chest wall afferent information to respiratory timing. Rib cage and abdominal motion were monitored by magnetometers and flow and tidal volume via a face mask. In the first group, studies were done in REM sleep when spontaneously occurring distortion of the rib cage occurred and a significant linear relationship between the rate of distortion of the chest wall and shortening of the inspiratory time (Ti) was found in all infants. Reduction in this distortion by the use of continuous positive airway pressure (CPAP) or continuous negative pressure at the body surface (CNeg) was associated with a significant (P less than 0.01) lengthening of Ti. Absence of changes in Ti when pressure was applied in quiet sleep suggested that lung volume or chemical changes were not involved. In the second group of infants we artificially generated the afferent inflow by using vibratory stimuli applied in one intercostal interspace and produced a significant (P less than 0.05) shortening in Ti. We suggest that the distortion of the rib cage in REM sleep generates afferent information from intercostal muscle spindles that is related to the rate of distortion and this, via a supraspinal reflex, inhibits phrenic motoneuron discharge. It may then be of importance in the etiology of apneic episodes in these infants. Applied pressure may be of benefit because it reduces an inhibitory afferent inflow.


Sign in / Sign up

Export Citation Format

Share Document