scholarly journals Multiuser Equalizer for Hybrid Massive MIMO mmWave CE-OFDM Systems

2019 ◽  
Vol 9 (16) ◽  
pp. 3363 ◽  
Author(s):  
Roberto Magueta ◽  
Sara Teodoro ◽  
Daniel Castanheira ◽  
Adão Silva ◽  
Rui Dinis ◽  
...  
Keyword(s):  
Orthogonal Frequency Division Multiplexing ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Decision Feedback ◽  
Hybrid Architecture ◽  
Ofdm Systems ◽  
Digital Architecture ◽  
Constant Envelope ◽  
Input Multiple Output ◽  
Analog Part

This paper considers a multiuser broadband uplink massive multiple input multiple output (MIMO) millimeter-wave (mmWave) system. The constant envelope orthogonal frequency division multiplexing (CE-OFDM) is adopted as a modulation technique to allow an efficient power amplification, fundamental for mmWave based systems. Furthermore, a hybrid architecture is considered at the user terminals (UTs) and base station (BS) to reduce the high cost and power consumption required by a full-digital architecture, which has a radio frequency (RF) chain per antenna. Both the design of the UT’s precoder and base station equalizer are considered in this work. With the aim of maximizing the beamforming gain between each UT and the BS, the precoder analog coefficients are computed as a function of the average angles of departure (AoD), which are assumed to be known at the UTs. At the BS, the analog part is derived by assuming a system with no multi-user interference. Then, a per carrier basis nonlinear/iterative multi-user equalizer, based on the iterative block decision feedback equalization (IB-DFE) principle is designed, to explicitly remove both the multi-user and residual inter carrier interferences, not tackled in the analog part. The equalizer design metric is the sum of the mean square error (MSE) of all subcarriers, whose minimization is shown to be equivalent to the minimization of a weighted error between the hybrid and the full digital equalizer matrices. The results show that the proposed hybrid multi-user equalizer has a performance close to the fully digital counterpart.

A companding approach for PAPR suppression in OFDM based massive MIMO system

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Ajay Kumar Yadav ◽  
Pritam Keshari Sahoo ◽  
Yogendra Kumar Prajapati
Keyword(s):  
Massive Mimo ◽  
Orthogonal Frequency Division Multiplexing ◽  
Mimo System ◽  
Multiple Input Multiple Output ◽  
Average Power ◽  
Base Station ◽  
Convex Optimization Problem ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Mimo Ofdm

Abstract Orthogonal frequency division multiplexing (OFDM) based massive multiuser (MU) multiple input multiple output (MIMO) system is popularly known as high peak-to-average power ratio (PAPR) issue. The OFDM-based massive MIMO system exhibits large number of antennas at Base Station (BS) due to the use of large number of high-power amplifiers (HPA). High PAPR causes HPAs to work in a nonlinear region, and hardware cost of nonlinear HPAs are very high and also power inefficient. Hence, to tackle this problem, this manuscript suggests a novel scheme based on the joint MU precoding and PAPR minimization (PP) expressed as a convex optimization problem solved by steepest gradient descent (GD) with μ-law companding approach. Therefore, we develop a new scheme mentioned to as MU-PP-GDs with μ-law companding to minimize PAPR by compressing and enlarging of massive MIMO OFDM signals simultaneously. At CCDF = 10−3, the proposed scheme (MU-PP-GDs with μ-law companding for Iterations = 100) minimizes the PAPR to 3.70 dB which is better than that of MU-PP-GDs, (iteration = 100) as shown in simulation results.

scholarly journals A Survey on Massive MIMO Systems in Presence of Channel and Hardware Impairments

Sensors ◽  
2019 ◽  
Vol 19 (1) ◽  
pp. 164 ◽  
Author(s):  
Zahra Mokhtari ◽  
Maryam Sabbaghian ◽  
Rui Dinis
Keyword(s):  
Massive Mimo ◽  
Orthogonal Frequency Division Multiplexing ◽  
Mimo Systems ◽  
Low Cost ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Aging Effects ◽  
Hardware Impairments ◽  
Single Carrier ◽  
Input Multiple Output

Massive multiple input multiple output (MIMO) technology is one of the promising technologies for fifth generation (5G) cellular communications. In this technology, each cell has a base station (BS) with a large number of antennas, allowing the simultaneous use of the same resources (e.g., frequency and/or time slots) by multiple users of a cell. Therefore, massive MIMO systems can bring very high spectral and power efficiencies. However, this technology faces some important issues that need to be addressed. One of these issues is the performance degradation due to hardware impairments, since low-cost RF chains need to be employed. Another issue is the channel estimation and channel aging effects, especially in fast mobility environments. In this paper we will perform a comprehensive study on these two issues considering two of the most promising candidate waveforms for massive MIMO systems: Orthogonal frequency division multiplexing (OFDM) and single-carrier frequency domain processing (SC-FDP). The studies and the results show that hardware impairments and inaccurate channel knowledge can degrade the performance of massive MIMO systems extensively. However, using suitable low complex estimation and compensation techniques and also selecting a suitable waveform can reduce these effects.

scholarly journals Peak Average Power Ratio Reduction Technique for Better Performance with Multi Input Multi Output

2019 ◽  
Vol 8 (6S) ◽  
pp. 199-202
Keyword(s):  
Orthogonal Frequency Division Multiplexing ◽  
Multiple Input Multiple Output ◽  
Average Power ◽  
Reduction Technique ◽  
Papr Reduction ◽  
Power Ratio ◽  
Ofdm Systems ◽  
Reduction Techniques ◽  
Input Multiple Output ◽  
Power Ratio Reduction

In the transmitted signal, the high peak-toaverage power ratio (PAPR) is the real disadvantage of multiple input, multiple output (MIMO) orthogonal frequency division multiplexing (OFDM) systems. Among different PAPR reduction techniques, selected mapping (SLM) is a famous strategy that accomplishes good PAPR reduction performance without signal distortion. Likewise, Partial transmit sequence (PTS) is additionally solitary of the successful techniques to decrease the PAPR in OFDM. Though, result an optimal segment issue in PTS system is measured to exist a critical concern. To progress the existing PAPR reduction techniques, we have incorporated ideal SLM and PTS based PAPR reduction strategy in parallel. By utilizing, the OGWO algorithm; the transmit succession was chosen with least PAPR above all communication antennas. The proposed PAPR reduction approach is applied independently on each transmitted antenna, and so the PAPR can be extremely reduced. Moreover, the OGWO optimization based PAPR reduction technique will provide better performance and it was been promoted as an uncomplicated way for PAPR reduction. The proposed approach will be analyzed with various novel PAPR reduction schemes to show the effectiveness.

scholarly journals An Efficient Algorithm for mmWave MIMO Systems

Symmetry ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 786 ◽  
Author(s):  
Imran Khan ◽  
Mohammed H. Alsharif ◽  
Mohammad Haseeb Zafar ◽  
Madini O. Alassafi ◽  
Majid Ashraf ◽  
...  
Keyword(s):  
Data Streams ◽  
Optimization Problem ◽  
Mimo Systems ◽  
State Of The Art ◽  
Multiple Input Multiple Output ◽  
Digital Architecture ◽  
Multiple Data ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Analog Part

Efficient and Symmetry based precoding plays a key role in wireless communications. In order to improve the transmission performance of multi-user millimeter wave Multiple-Input Multiple-Output (MIMO) (MU-mmWave MIMO) systems, this paper proposes an analog precoding scheme for the receiver of mmWave MIMO with split sub-array hybrid analog and digital architecture. Then, we propose a hybrid analog and digital precoding algorithm based on channel reciprocity (APoCR) to maximize the spectral efficiency by utilizing the triple joint optimization problem, which can be divided into the analog and digital part. The analog combination vectors (ACVs) are obtained by the signal-to-interference-and-noise ratio (SINR) reception maximization of each downlink user and the analog precoding vectors (APVs) are obtained by the SINR reception maximization of each uplink antenna array. The digital precoder of the transmitter is designed after the analog part optimization to alleviate the interference between multiple data streams of the users. The simulation results show that the proposed precoding algorithm has a better sum rate, fast convergence, and improved SINR than the other state-of-the-art algorithms.

scholarly journals Phase Noise Effect on MIMO-OFDM Systems with Common and Independent Oscillators

2017 ◽  
Vol 2017 ◽  
pp. 1-12 ◽  
Author(s):  
Xiaoming Chen ◽  
Hua Wang ◽  
Wei Fan ◽  
Yaning Zou ◽  
Andreas Wolfgang ◽  
...  
Keyword(s):  
Orthogonal Frequency Division Multiplexing ◽  
Multiple Input Multiple Output ◽  
Spatial Multiplexing ◽  
Ofdm Systems ◽  
Error Vector Magnitude ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Mimo Ofdm ◽  
Value Decomposition ◽  
Vector Magnitude

The effects of oscillator phase noises (PNs) on multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) systems are studied. It is shown that PNs of common oscillators at the transmitter and at the receiver have the same influence on the performance of (single-stream) beamforming MIMO-OFDM systems, yet different influences on spatial multiplexing MIMO-OFDM systems with singular value decomposition (SVD) based precoding/decoding. When each antenna is equipped with an independent oscillator, the PNs at the transmitter and at the receiver have different influences on beamforming MIMO-OFDM systems as well as spatial multiplexing MIMO-OFDM systems. Specifically, the PN effect on the transmitter (receiver) can be alleviated by having more transmit (receive) antennas for the case of independent oscillators. It is found that the independent oscillator case outperforms the common oscillator case in terms of error vector magnitude (EVM).

scholarly journals Synchronization in MIMO OFDM systems

2005 ◽  
Vol 2 ◽  
pp. 147-153 ◽  
Author(s):  
L. Häring ◽  
A. Czylwik
Keyword(s):  
Carrier Frequency ◽  
Orthogonal Frequency Division Multiplexing ◽  
Carrier Frequency Offset ◽  
Mimo Systems ◽  
Multiple Input Multiple Output ◽  
High Sensitivity ◽  
Ofdm Systems ◽  
Single Input Single Output ◽  
Input Multiple Output ◽  
Single Input

Abstract. In this paper, an overview of carrier frequency offset (CFO) estimation algorithms for Orthogonal Frequency Division Multiplexing (OFDM) systems is presented. It is well-known that multicarrier systems suffer from their high sensitivity to mismatches of transmitter and receiver oscillator frequencies. The performance degrades since the CFO destroys the orthogonality of the subcarriers. Hence, extensive research has been done on the estimation and correction of the CFO in Single-Input Single-Output (SISO) systems. Mainly, the proposed algorithms can be categorized into data-aided and blind techniques. Several estimation techniques have been extended to the Single-Input Multiple- Output (SIMO) case where multiple receive antennas can be utilized to gain diversity. However, less attention has been paid on synchronization in the attractive Multiple-Input Multiple-Output (MIMO) case which is topic of tremendous interest in current research. The present paper concentrates on aspects of this new scenario. Starting with algorithms for SISO and SIMO, this contribution reviews briefly proposed carrier frequency synchronization techniques which could be implemented in forthcoming MIMO systems.

scholarly journals Performance enhancement of maximum ratio transmission in 5G system with multi-user multiple-input multiple-output

2022 ◽  
Vol 12 (2) ◽  
pp. 1650
Author(s):  
Sarmad K. Ibrahim ◽  
Saif A. Abdulhussien
Keyword(s):  
Massive Mimo ◽  
Orthogonal Frequency Division Multiplexing ◽  
Performance Enhancement ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Standard System ◽  
Multiple Input ◽  
Input Multiple Output ◽  
Ratio Transmission ◽  
Maximum Ratio Transmission

<span>The downlink multi-user precoding of the multiple-input multiple-output (MIMO) method includes optimal channel state information at the base station and a variety of linear precoding (LP) schemes. Maximum ratio transmission (MRT) is among the common precoding schemes but does not provide good performance with massive MIMO, such as high bit error rate (BER) and low throughput. The orthogonal frequency division multiplexing (OFDM) and precoding schemes used in 5G have a flaw in high-speed environments. Given that the Doppler effect induces frequency changes, orthogonality between OFDM subcarriers is disrupted and their throughput output is decreased and BER is decreased. This study focuses on solving this problem by improving the performance of a 5G system with MRT, specifically by using a new design that includes weighted overlap and add (WOLA) with MRT. The current research also compares the standard system MRT with OFDM with the proposed design (WOLA-MRT) to find the best performance on throughput and BER. Improved system results show outstanding performance enhancement over a standard system, and numerous improvements with massive MIMO, such as best BER and throughput. Its approximately 60% more throughput than the traditional systems. Lastly, the proposed system improves BER by approximately 2% compared with the traditional system.</span>

scholarly journals Uplink Multiuser MIMO-OFDM System in the Presence of Phase Noises, Power Imbalance, and Correlation

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Xiaoming Chen ◽  
Andreas Wolfgang ◽  
Tommy Svensson
Keyword(s):  
Orthogonal Frequency Division Multiplexing ◽  
Mimo Systems ◽  
Multiple Input Multiple Output ◽  
Base Station ◽  
Closed Form Expression ◽  
Ofdm System ◽  
Multiuser Mimo ◽  
Single Antenna ◽  
Input Multiple Output ◽  
Mimo Ofdm

The effects of phase noises (PNs), power imbalances, and correlations on multiuser orthogonal frequency division multiplexing (OFDM) multiple-input multiple-output (MIMO) systems are studied. It is assumed that each user is equipped with a single antenna, whereas the base station (BS) has multiple antennas and use zero-forcing (ZF) decoder for multiuser detection. Since each user has an independent oscillator, the received uplink (UL) signal at each BS antenna is corrupted by all of these independent PNs. Furthermore, there may be power imbalances and correlations (due to common scatterers) between different users. These impairments are jointly analyzed in this work. A closed-form expression of the mean square error (MSE) performance of the multiuser MIMO-OFDM system is derived. The analytical results are verified by simulations.

scholarly journals A Low Rank Channel Estimation Scheme in Massive Multiple-Input Multiple-Output

Symmetry ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 507 ◽  
Author(s):  
Waleed Shahjehan ◽  
Syed Shah ◽  
Jaime Lloret ◽  
Antonio Leon
Keyword(s):  
Channel Estimation ◽  
Orthogonal Frequency Division Multiplexing ◽  
Multiple Input Multiple Output ◽  
Block Matching ◽  
Low Rank ◽  
Frequency Division ◽  
Ofdm Systems ◽  
Transmission Scheme ◽  
Multiple Input ◽  
Input Multiple Output

Aiming at the problem of computational complexity of channel estimation, this paper proposes a low-complexity block matching pursuit (BMP) algorithm based on antenna grouping and block sparsity for frequency division duplex (FDD) massive Multiple-input Multiple-output orthogonal frequency division multiplexing (OFDM) systems. The system coherence time may be exceeded as a result of time consumption when adopting an orthogonal pilot symbol in the time domain. To solve this problem, an antenna grouping transmission scheme is proposed to reduce the total channel estimation time by sacrificing the observed data length. The simulation results show that the proposed BMP algorithm has good anti-noise performance, and it can accurately determine the non-zero position of the sparse vector and adaptively determine the sparsity of the channel, which effectively translates to improved channel estimation performance and better overall system performance than the existing algorithms.

scholarly journals An Efficient Two-Stage Receiver Base on AOR Iterative Algorithm and Chebyshev Acceleration for Uplink Multiuser Massive-MIMO OFDM Systems

Electronics ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 92
Author(s):  
Yung-Ping Tu ◽  
Chih-Yung Chen ◽  
Kuang-Hao Lin
Keyword(s):  
Iterative Algorithm ◽  
Communication Systems ◽  
Orthogonal Frequency Division Multiplexing ◽  
Multiple Input Multiple Output ◽  
Superior Performance ◽  
Ofdm Systems ◽  
Two Stage ◽  
Multiuser Detector ◽  
Input Multiple Output ◽  
Mimo Ofdm

The massive multiple-input multiple-output systems (M-MIMO) and orthogonal frequency-division multiplexing (OFDM) are considered to be some of the most promising key techniques in the emerging 5G and advanced wireless communication systems nowadays. Not only are the benefits of applying M-MIMO and OFDM for broadband communication well known, but using them for the application of the Internet of Things (IoT) requires a large amount of wireless transmission, which is a developing topic. However, its high complexity becomes a problem when there are numerous antennas. In this paper, we provide an effective two-stage multiuser detector (MUD) with the assistance of the accelerated over-relaxation (AOR) iterative algorithm and Chebyshev acceleration for the uplink of M-MIMO OFDM systems to achieve a better balance between bit error rate (BER) performance and computational complexity. The first stage of the receiver consists of an accelerated over-relaxation (AOR)-based estimator and is intended to yield a rough initial estimate of the relaxation factor ω, the acceleration parameter γ, and transmitted symbols. In the second stage, the Chebyshev acceleration method is used for detection, and a more precise signal is produced through efficient iterative estimation. Additionally, we call this proposed scheme Chebyshev-accelerated over-relaxation (CAOR) detection. Conducted simulations show that the developed receiver, with a modest computational load, can provide superior performance compared with previous works, especially in the MU M-MIMO uplink environments.

Sign in / Sign up

Export Citation Format

Share Document