scholarly journals An Experimental Study of the Effects of Low-Calcium Fly Ash on Type II Concrete

Ceramics ◽  
2021 ◽  
Vol 4 (4) ◽  
pp. 600-617
Author(s):  
Kong Fah Tee ◽  
Sayedali Mostofizadeh
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Weight Ratio ◽  
High Strength ◽  
Cementitious Materials ◽  
Alkaline Solutions ◽  
Curing Period ◽  
Low Calcium ◽  
Permeation Properties

In this study, the compressive strength and the permeation properties of fly ash-based Geopolymer were experimentally investigated. Type 2 Portland cement (T2PC) was partially or entirely replaced with 0, 10, 20, 30, 50, 70, and 100% of fly ash (FA). The laboratory tests were conducted for compressive strength at 7, 28, and 90 days, and permeation properties such as water absorption at 7 and 28 days. The main goal was to produce eco-friendly concrete with high strength and low permeability through blending cementitious materials including low Calcium (Ca) (T2PC and FA) for protecting concrete against sulphate attacks and other chemically destructive compounds in the environment. This study focused on the effectiveness of the curing period, combinations of chemical activators by varying the molarity of alkaline solutions between 4.16 and 12.96 M and keeping the sodium silicate (SS) to sodium hydroxide (SH) by the weight ratio of 2.5. Lab observations from this study demonstrated that the compressive strength was enhanced with the increment in fly ash content at all ages, with optimum being at 20% as the replacement of T2PC.

Water Penetration Resistance of Fly Ash Concrete Incorporating with Quarry Wastes

2017 ◽  
Vol 886 ◽  
pp. 159-163 ◽  
Author(s):  
Suppachai Sinthaworn
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength ◽  
Cementitious Materials ◽  
Fine Aggregate ◽  
Water Penetration ◽  
Strength Concrete ◽  
Fly Ash Concrete ◽  
Suitable Amount ◽  
Normal Strength

Slump of fresh concrete, compressive strength and water penetration depth under pressure of fly ash concrete incorporate with quarry waste as fine aggregate were investigated. The cementitious materials of the concrete includes ordinary Portland cement 80% and fly ash 20% by weight of cementitious. The mix proportions of the concrete were set into two classes of compressive strength. The results show that fly ash enhances workability of both concretes (normal concrete and concrete incorporate with quarry waste). Increasing the percentage of quarry dusts as fine aggregate in concrete seem negligible effect on the compressive strength whereas adding fly ash shows a slightly improve the compressive strength in the case of cohesive concrete mixture. Besides, adding the suitable amount of fly ash could improve the permeability of concrete. Therefore, fly ash could be a good admixture to improve the water resistant of normal strength concrete and also could be a supplemental material to improve the compressive strength of normal high strength concrete.

scholarly journals Physical and Mechanical Properties of High-Strength Concrete Modified with Supplementary Cementitious Materials after Exposure to Elevated Temperature up to 1000 °C

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 532 ◽  
Author(s):  
Jianwei Zhou ◽  
Dong Lu ◽  
Yuxuan Yang ◽  
Yue Gong ◽  
Xudong Ma ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Water Absorption ◽  
High Strength Concrete ◽  
Elevated Temperatures ◽  
High Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Concrete

This paper presents the experimental findings of a study on the influence of combining usage of supplementary cementitious materials (SCMs) on the performance of high-strength concrete (HSC) subjected to elevated temperatures. In this study, four types of HSC formulations were prepared: HSC made from cement and fly ash (FA), HSC made from cement and ultra-fine fly ash (UFFA), HSC made from cement and UFFA-metakaolin (MK), and HSC made from cement and FA-UFFA-MK. Mechanical and physical properties of HSC subjected to high temperatures (400, 600, 800, and 1000 °C) were studied. Furthermore, the relation between residual compressive strength and physical properties (loss mass, water absorption, and porosity) of HSC was developed. Results showed that the combined usage of SCMs had limited influence on the early-age strength of HSC, while the 28-d strength had been significantly affected. At 1000 °C, the residual compressive strength retained 18.7 MPa and 23.9 MPa for concretes containing 30% UFFA-5% MK and 10% FA-20% UFFA-5% MK, respectively. The specimen containing FA-UFFA-MK showed the best physical properties when the temperature raised above 600 °C. Combined usage of SCMs (10% FA-20% UFFA-5% MK) showed the lowest mass loss (9.2%), water absorption (10.9%) and porosity (28.6%) at 1000 °C. There was a strongly correlated relation between residual strength and physical properties of HSC exposed to elevated temperatures.

Investigation on a New Hydraulic Cementitious Binder Made from Phosphogypsum

2013 ◽  
Vol 864-867 ◽  
pp. 1923-1928
Author(s):  
Yue Xu ◽  
Jian Xi Li ◽  
Li Li Kan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Active Carbon ◽  
High Strength ◽  
Tricalcium Silicate ◽  
Dicalcium Silicate ◽  
Cementitious Material ◽  
Saturation Ratio ◽  
Tricalcium Aluminate ◽  
Cementitious Binder

A new kind of high strength cementitious material is made from phosphogypsum (PG), active carbon and fly-ash. Through the orthogonal research, it was showed that the calcination temperature, retention time, dosage of active carbon and fly ash on the compressive strength of cementitious binder are the most important. The result also showed that, in the conditions of temperature 1200°C, time retention 30 min, dosage of active carbon 10%, dosage of fly ash 5%, the compressive strength of the cementitious material for 3d and 28d could reach to 46.35MPa and 92.70MPa, the content of sulfur trioxide was 11.60% accordingly. A lot of active mineral materials, such as dicalcium silicate, tricalcium silicate, tricalcium aluminate were formed in the calcination. The C-S-H gel, calcium hydroxide and ettringite were found in 3d and 28d hydrates. It is found that the lime saturation ratio and silica modulus need to be control between 0.40~0.65 and 4~8 in order to produce high strength cementitious material.

Effect of Chopped Basalt Fiber on the Fresh and Hardened Properties of Fly Ash High Strength Concrete

2014 ◽  
Vol 567 ◽  
pp. 381-386 ◽  
Author(s):  
Nasir Shafiq ◽  
Muhd Fadhil Nuruddin ◽  
Ali Elheber Ahmed Elshekh ◽  
Ahmed Fathi Mohamed Salih
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
High Strength Concrete ◽  
Basalt Fiber ◽  
High Strength ◽  
Progressive Increase ◽  
Test Results ◽  
Strength Concrete ◽  
Hardened Properties ◽  
Chopped Basalt Fiber

In order to improve the mechanical properties of high strength concrete, HSC, several studies have been conducted using fly ash, FA. Researchers have made it possible to achieve 100-150MPa high strength concrete. Despite the popularity of this FAHSC, there is a major shortcoming in that it becomes more brittle, resulting in less than 0.1% tensile strain. The main objective of this work was to evaluate the fresh and hardened properties of FAHSC utilizing chopped basalt fiber stands, CBFS, as an internal strengthening addition material. This was achieved through a series of experimental works using a 20% replacement of cement by FA together with various contents of CBFS. Test results of concrete mixes in the fresh state showed no segregation, homogeneousness during the mixing period and workability ranging from 60 to 110 mm. Early and long terms of compressive strength did not show any improvement by using CBFS; in fact, it decreased. This was partially substituted by the effect of FA. Whereas, the split and flexural strengths of FASHC were significantly improved with increasing the content of CBFS as well as the percentage of the split and flexural tensile strength to the compressive strength. Also, test results showed a progressive increase in the areas under the stress-strain curves of the FAHSC strains after the CBFS addition. Therefore, the brittleness and toughness of the FAHSC were enhanced and the pattern of failure moved from brittle failure to ductile collapse using CBFS. It can be considered that the CBFS is a suitable strengthening material to produce ductile FAHSC.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Influence of Partial Replacement of Micro-Silica by Fly-Ash on Strength Properties of Reactive Powder Concrete

2020 ◽  
Vol 9 (3) ◽  
pp. 2932-2937
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Mechanical Performance ◽  
Cementitious Materials ◽  
Partial Replacement ◽  
Reactive Powder Concrete ◽  
Experimental Investigations ◽  
Reactive Powder ◽  
Micro Silica

Reactive powder concrete (RPC) is the ultra-high strength concrete made by cementitious materials like silica fumes, cement etc. The coarse aggregates are completely replaced by quartz sand. Steel fibers which are optional are added to enhance the ductility. Market survey has shown that micro-silica is not so easily available and relatively costly. Therefore an attempt is made to experimentally investigate the reduction of micro-silica content by replacing it with fly-ash and mechanical properties of modified RPC are investigated. Experimental investigations show that compressive strength decreases gradually with addition of the fly ash. With 10 per cent replacement of micro silica, the flexural and tensile strength showed 40 and 46 per cent increase in the respective strength, though the decrease in the compressive strength was observed to be about 20 per cent. For further percentage of replacement, there was substantial drop in compressive, flexural as well as tensile strength. The experimental results thereby indicates that utilisation of fly-ash as a partial replacement to micro silica up to 10 per cent in RPC is feasible and shows quite acceptable mechanical performance with the advantage of utilisation of fly-ash in replacement of micro-silica.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Compressive strength and microstructure evolution of low calcium brown coal fly ash-based geopolymer

2019 ◽  
Vol 9 (1) ◽  
pp. 17-34 ◽  
Author(s):  
Muhamed Khodr ◽  
David W. Law ◽  
Chamila Gunasekara ◽  
Sujeeva Setunge ◽  
Robert Brkljaca
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Brown Coal ◽  
Microstructure Evolution ◽  
Coal Fly Ash ◽  
Low Calcium
Sign in / Sign up

Export Citation Format

Share Document