scholarly journals Alkali-Activated Hybrid Concrete Based on Fly Ash and Its Application in the Production of High-Class Structural Blocks

Crystals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 946
Author(s):  
Oriana Rojas-Duque ◽  
Lina Marcela Espinosa ◽  
Rafael A. Robayo-Salazar ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Modulus ◽  
Setting Time ◽  
Modulus Of Rupture ◽  
Strength Development ◽  
Block Type ◽  
High Class ◽  
Structural Blocks ◽  
Alkali Activated

This article reports the production and characterization of a hybrid concrete based on the alkaline activation of a fly ash (FA) of Colombian origin, which was added with 10% Portland cement (OPC) in order to promote the compressive strength development at room temperature. The alkali-activated hybrid cement FA/OPC 90/10 was classified as a low heat reaction cement (type LH), according to American Society of Testing Materials, ASTM C1157; the compressive strength was of 31.56 MPa and of 22.68 MPa (28 days) at the levels of paste and standard mortar, respectively, with an initial setting time of 93.3 min. From this binder, a hybrid concrete was produced and classified as a structural type, with a compressive strength of 23.16 MPa and a flexural modulus of rupture of 5.32 MPa, at 28 days of curing. The global warming potential index (GWP 100), based on life cycle analysis, was 35% lower than the reference concrete based on 100% OPC. Finally, its use was validated in the manufacture of a solid block-type construction element, which reached a compressive strength of 21.9 MPa at 28 days, exceeding by 40.6% the minimum strength value established by the Colombia Technical Standard, NTC 4026 (13 MPa) to be classified as high class structural blocks.

Experimental Study on Alkali-Activated Slag-Lithium Slag-Fly Ash Environmental Concrete

2011 ◽  
Vol 287-290 ◽  
pp. 1237-1240
Author(s):  
Lan Fang Zhang ◽  
Rui Yan Wang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Fly Ash ◽  
Setting Time ◽  
Alkali Activated Slag ◽  
Percent Increase ◽  
Compressive Strength Of Concrete ◽  
Activated Slag ◽  
Lithium Slag ◽  
Alkali Activated

The aim of this paper is to study the influence of lithium-slag and fly ash on the workability , setting time and compressive strength of alkali-activated slag concrete. The results indicate that lithium-slag and fly-ash can ameliorate the workability, setting time and improve the compressive strength of alkali-activated slag concrete，and when 40% or 60% slag was replaced by lithium-slag or fly-ash, above 10 percent increase in 28-day compressive strength of concrete were obtained.

scholarly journals Effect of calcium-rich compounds on setting time and strength development of alkali-activated fly ash cured at ambient temperature

2018 ◽  
Vol 9 ◽  
pp. e00198 ◽  
Author(s):  
Prinya Chindaprasirt ◽  
Tanakorn Phoo-ngernkham ◽  
Sakonwan Hanjitsuwan ◽  
Suksun Horpibulsuk ◽  
Anurat Poowancum ◽  
...  
Keyword(s):  
Fly Ash ◽  
Ambient Temperature ◽  
Setting Time ◽  
Strength Development ◽  
Alkali Activated

scholarly journals Influence of Mechanical and Mineralogical Activation of Biomass Fly Ash on the Compressive Strength Development of Cement Mortars

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6654
Author(s):  
Jakub Popławski ◽  
Małgorzata Lelusz
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cement Mortar ◽  
Setting Time ◽  
Green Energy ◽  
Biomass Combustion ◽  
Strength Development ◽  
Compressive Strength Development ◽  
Biomass Fly Ash

Biomass combustion is a significant new source of green energy in the European Union. The adequate utilization of byproducts created during that process is a growing challenge for the energy industry. Biomass fly ash could be used in cement composite production after appropriate activation of that material. This study had been conducted to assess the usefulness of mechanical and physical activation methods (grinding and sieving), as well as activation through the addition of active silica in the form of silica fume, as potential methods with which to activate biomass fly ash. Setting time, compressive strength, water absorption and bulk density tests were performed on fresh and hardened mortar. While all activation methods influenced the compressive strength development of cement mortar with fly ash, sieving of the biomass fly ash enhanced the early compressive strength of cement mortar. The use of active silica in the form of silica fume ensured higher compressive strength results than those of control specimens throughout the entire measurement period.

Interrelationship Analysis of Geopolymer Components Using Pearson Correlation Technique

2014 ◽  
Vol 567 ◽  
pp. 417-421 ◽  
Author(s):  
Andri Kusbiantoro ◽  
Norbaizurah Rahman ◽  
Noor Fifinatasha Shahedan
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Elemental Composition ◽  
Setting Time ◽  
Source Material ◽  
Curing Temperature ◽  
Strength Development ◽  
Correlation Technique ◽  
High Calcium ◽  
Geopolymer Binder

Performance of geopolymer based specimens is significantly affected by internal and external aspects. Curing temperature and air humidity are among the prominent external factors that contribute to the alteration of geopolymer properties. Nevertheless, internal component of geopolymer binder also carries essential effect to the hardened geopolymer binder produced. In this research, the study was concentrated on the elemental composition of source material components and their interrelation to the performance of geopolymer binder produced. Different types of fly ash were used as the source material in this research. Low calcium (class-F) fly ash was combined with high calcium (class-C) fly ash to determine the elemental composition effect, particularly SiO2, Al2O3, and CaO to the geopolymer properties. Analysis using SYSTAT statistical software indicated the importance of oxide composition of source material to the geopolymer specimens produced. Initial setting time of geopolymer paste was also possibly important to the compressive strength of geopolymer specimens produced. Nevertheless, final setting time indicated less importance to the compressive strength development of geopolymer binder.

Development of Non-Autoclaved Aerated Concrete by Alkali Activated Phosphorus Slag

2011 ◽  
Vol 250-253 ◽  
pp. 1147-1152 ◽  
Author(s):  
Xiao Jun Jiang ◽  
Yan Yun ◽  
Zhi Hua Hu
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Bulk Density ◽  
Sodium Silicate ◽  
Setting Time ◽  
Liquid Sodium ◽  
Molar Ratio ◽  
Autoclaved Aerated Concrete ◽  
Aerated Concrete ◽  
Alkali Activated

The feasibility of manufacturing non-autoclaved aerated concrete using alkali activated phosphorus slag as a cementitious material was investigated in this paper. Liquid sodium silicate with various modules (the molar ratio between SiO2 and Na2O) was used as alkali activator and a part of phosphorus slag was replaced with fly ash which was used to control the setting time of aerated concrete. The influences of the fly ash, curing procedure, modulus of sodium silicate solution and concentration of alkalis on the compressive strength and bulk density of non-autoclaved aerated concrete have been studied. Moreover, the types of the hydration products were investigated using XRD and SEM. The results indicate that: the compressive strength of aerated concrete was influenced by concentration of alkalis obviously. The compressive strength of 11.9MPa and the bulk density of 806kg/m3 were obtained with an activator of 1.2 modulus of sodium silicate and 6% concentration of alkalis under the circumstance of 60°C curing for 28 days.

scholarly journals Rapid Indicators in Detecting Variation of Fly Ash for Making HVFA Concrete

2015 ◽  
Vol 815 ◽  
pp. 153-157 ◽  
Author(s):  
Antoni ◽  
Rianto Gunawan ◽  
Djwantoro Hardjito
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Water Solution ◽  
Setting Time ◽  
Cementitious Materials ◽  
Strength Development ◽  
Quick Method ◽  
Alternative Material

The use of fly ash as an alternative material for cement substitute in concrete mix already a common practice nowadays. However, as a waste material, fly ash varies in quality and condition, as shown by variation of its fineness, specific gravity, Loss on Ignition (LOI) and also on its chemical composition. By measuring the acidity (pH) of the fly ash in water solution, percentage of mass retained on 45 μm sieve, and superplasticizer demand of the fly ash, we can develop a quick estimation of the quality of fly ash. This study aims to investigate a quick method to estimate the quality of fly ash by measuring the physical and chemical pointers, as indicator for its properties and the effect on the setting time and compressive strength of mortar. Fly ash content was varied from 0-70% of the total mass of cementitious materials to make HVFA mortar. Fly ashes were obtained from four power plants in Indonesia. Tests conducted were material characterization, setting time, temperature rise, and compressive strength of mortar at different ages. Different fly ash quality can be shown by the fast pointers; namely pH, superplasticizer demand and % retained on 45 μm sieve. Setting time and strength development were affected by the different properties of fly ash.

scholarly journals Effect of the Sodium Silicate Modulus and Slag Content on Fresh and Hardened Properties of Alkali-Activated Fly Ash/Slag

Minerals ◽  
2019 ◽  
Vol 10 (1) ◽  
pp. 15 ◽  
Author(s):  
Xiaowei Ouyang ◽  
Yuwei Ma ◽  
Ziyang Liu ◽  
Jianjun Liang ◽  
Guang Ye
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Pore Structure ◽  
Heat Release ◽  
Setting Time ◽  
Heat Evolution ◽  
Reaction Products ◽  
Hardened Properties ◽  
Alkali Activated ◽  
Slag Content

This paper presents the results of an experimental study performed to investigate the effect of activator modulus (SiO2/Na2O) and slag addition on the fresh and hardened properties of alkali-activated fly ash/slag (AAFS) pastes. Four activator moduli (SiO2/Na2O), i.e., 0.0, 1.0, 1.5, and 2.0, and five slag-to-binder ratios, i.e., 0, 0.3, 0.5, 0.7, 1.0, were used to prepare AAFS mixtures. The setting time, flowability, heat evolution, compressive strength, microstructure, and reaction products of AAFS pastes were studied. The results showed that the activator modulus and slag content had a combined effect on the setting behavior and workability of AAFS mixtures. Both the activator modulus and slag content affected the types of reaction products formed in AAFS. The coexistence of N–A–S–H gel and C–A–S–H gel was identified in AAFS activated with high pH but low SiO2 content (low modulus). C–A–S–H gel had a higher space-filling ability than N–A–S–H gel. Thus, AAFS with higher slag content had a finer pore structure and higher heat release (degree of reaction), corresponding to a higher compressive strength. The dissolution of slag was more pronounced when NaOH (modulus of 0.0) was applied as the activator. The use of Na2SiO3 as activator significantly refined the pores in AAFS by incorporating soluble Si in the activator, while further increasing the modulus from 1.5 to 2.0 prohibited the reaction process of AAFS, resulting in a lower heat release, coarser pore structure, and reduced compressive strength. Therefore, in view of the strength and microstructure, the optimum modulus is 1.5.

scholarly journals Setting and Hardening Behaviour of Alkali-Activated Landfilled Fly Ash–Slag Binder at Room Temperature

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3130
Author(s):  
Wei Liu ◽  
Lin Lin ◽  
Shuping Wang ◽  
Xiaoqin Peng ◽  
Bobo Wu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Room Temperature ◽  
Setting Time ◽  
Three Dimensional ◽  
Industrial Wastes ◽  
Dimensional Structure ◽  
Strength Development ◽  
Na2o Content ◽  
Solid Ratio

A geopolymer is normally considered an environmentally friendly binder due to the utilisation of industrial wastes. This study focusses on the potential of geopolymer preparation at room temperature from landfilled fly ash (LFA) which has been discharged to the land for more than three years. To accelerate the reaction process, 20–30 wt.% LFA was replaced by ground-granulated blast-furnace slag (GGBS). The effect of water glass modulus, Na2O content, water-to-solid ratio, and GGBS content on the setting time and strength development of the binder was discussed. Results showed that to activate LFA, the optimal value of the sodium silicate modulus for alkaline solution was 1.4–1.6 with a Na2O content of 10%, and the water-to-solid ratio was 0.4. In addition, the setting time of the binder reduced with increasing content of GGBS replacement, and the compressive strength increased due to the coexistence of C–(A)–S–H and zeolite-like phases. The maximum compressive strength of the binder was 29.2 MPa after 56 days of curing. The relatively low strength was likely due to the absence of the Q4 unit with a three-dimensional structure.

Sign in / Sign up

Export Citation Format

Share Document