scholarly journals Comparing Cyclic Tension-Compression Effects on CoCrFeMnNi High-Entropy Alloy and Ni-Based Superalloy

Crystals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 420 ◽  
Author(s):  
Tu-Ngoc Lam ◽  
You-Shiun Chou ◽  
Yao-Jen Chang ◽  
Tsung-Ruei Sui ◽  
An-Chou Yeh ◽  
...  
Keyword(s):  
Lattice Strain ◽  
Cyclic Hardening ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Nickel Based Superalloy ◽  
Face Centered ◽  
Compression Effects ◽  
In Situ Neutron Diffraction

An equal-molar CoCrFeMnNi, face-centered-cubic (fcc) high-entropy alloy (HEA) and a nickel-based superalloy are studied using in situ neutron diffraction experiments. With continuous measurements, the evolution of diffraction peaks is collected for microscopic lattice strain analyses. Cyclic hardening and softening are found in both metallic systems. However, as obtained from the diffraction-peak-width evolution, the underneath deformation mechanisms are quite different. The CoCrFeMnNi HEA exhibits distinct lattice strain and microstructure responses under tension-compression cyclic loadings.

scholarly journals Vacuum brazing of Al2O3 and 3D printed Ti6Al4V lap-joints using high entropy driven AlZnCuFeSi filler

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn
Keyword(s):  
Strength Properties ◽  
Lap Joints ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
3D Printed ◽  
Face Centered ◽  
Alloy Filler

AbstractIn this work, we studied the brazing characteristics of Al2O3 and 3D printed Ti–6Al–4V alloys using a novel equiatomic AlZnCuFeSi high entropy alloy filler (HEAF). The HEAF was prepared by mechanical alloying of the constituent powder and spark plasma sintering (SPS) approach. The filler microstructure, wettability and melting point were investigated. The mechanical and joint strength properties were also evaluated. The results showed that the developed AlZnCuFeSi HEAF consists of a dual phase (Cu–Zn, face-centered cubic (FCC)) and Al–Fe–Si rich (base centered cubic, BCC) phases. The phase structure of the (Cu–Al + Ti–Fe–Si)/solid solution promises a robust joint between Al2O3 and Ti–6Al–4V. In addition, the joint interfacial reaction was found to be modulated by the brazing temperature and time because of the altered activity of Ti and Zn. The optimum shear strength reached 84 MPa when the joint was brazed at 1050 °C for 60 s. The results can be promising for the integration of completely different materials using the entropy driven fillers developed in this study.

scholarly journals Microstructure Refinement by Low-Temperature Ausforming in an Fe-Based Metastable High-Entropy Alloy

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 742
Author(s):  
Motomichi Koyama ◽  
Takeaki Gondo ◽  
Kaneaki Tsuzaki
Keyword(s):  
Low Temperature ◽  
Plastic Anisotropy ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Microstructure Refinement ◽  
Hexagonal Close Packed ◽  
Solution Treated Condition ◽  
Solution Treated ◽  
Face Centered

The effects of ausforming in an Fe30Mn10Cr10Co high-entropy alloy on the microstructure, hardness, and plastic anisotropy were investigated. The alloy showed a dual-phase microstructure consisting of face-centered cubic (FCC) austenite and hexagonal close-packed (HCP) martensite in the as-solution-treated condition, and the finish temperature for the reverse transformation was below 200 °C. Therefore, low-temperature ausforming at 200 °C was achieved, which resulted in microstructure refinement and significantly increased the hardness. Furthermore, plasticity anisotropy, a common problem in HCP structures, was suppressed by the ausforming treatment. This, in turn, reduced the scatter of the hardness.

scholarly journals In-Situ TEM Annealing Observation of Helium Bubble Evolution in Pre-Irradiated FeCoNiCrTi0.2 Alloys

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3727
Author(s):  
Huanhuan He ◽  
Zhiwei Lin ◽  
Shengming Jiang ◽  
Xiaotian Hu ◽  
Jian Zhang ◽  
...  
Keyword(s):  
Vacuum Arc ◽  
In Situ Tem ◽  
Face Centered Cubic ◽  
Helium Bubble ◽  
High Entropy ◽  
Helium Bubbles ◽  
Transmission Electron ◽  
Bubble Evolution ◽  
Face Centered

The FeCoNiCrTi0.2 high-entropy alloys fabricated by vacuum arc melting method, and the annealed pristine material, are face centered cubic structures with coherent γ’ precipitation. Samples were irradiated with 50 keV He+ ions to a fluence of 2 × 1016 ions/cm2 at 723 K, and an in situ annealing experiment was carried out to monitor the evolution of helium bubbles during heating to 823 and 923 K. The pristine structure of FeCoNiCrTi0.2 samples and the evolution of helium bubbles during in situ annealing were both characterized by transmission electron microscopy. The annealing temperature and annealing time affect the process of helium bubbles evolution and formation. Meanwhile, the grain boundaries act as sinks to accumulate helium bubbles. However, the precipitation phase seems have few effects on the helium bubble evolution, which may be due to the coherent interface and same structure of γ’ precipitation and matrix.

In situ neutron diffraction study of fatigue behavior of CrFeCoNiMo0.2 high entropy alloy

2021 ◽  
Vol 139 ◽  
pp. 107371
Author(s):  
Haiyan He ◽  
Bing Wang ◽  
Dong Ma ◽  
Alexandru D. Stoica ◽  
Zhenduo Wu ◽  
...  
Keyword(s):  
Neutron Diffraction ◽  
Diffraction Study ◽  
Fatigue Behavior ◽  
Neutron Diffraction Study ◽  
High Entropy Alloy ◽  
High Entropy ◽  
In Situ Neutron Diffraction

scholarly journals Correlating work hardening with co-activation of stacking fault strengthening and transformation in a high entropy alloy using in-situ neutron diffraction

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
M. Frank ◽  
S. S. Nene ◽  
Y. Chen ◽  
B. Gwalani ◽  
E. J. Kautz ◽  
...  
Keyword(s):  
Neutron Diffraction ◽  
Work Hardening ◽  
Dislocation Motion ◽  
Stacking Fault ◽  
Dislocation Slip ◽  
Simultaneous Increase ◽  
High Entropy Alloy ◽  
High Entropy ◽  
In Situ Neutron Diffraction

AbstractTransformation induced plasticity (TRIP) leads to enhancements in ductility in low stacking fault energy (SFE) alloys, however to achieve an unconventional increase in strength simultaneously, there must be barriers to dislocation motion. While stacking faults (SFs) contribute to strengthening by impeding dislocation motion, the contribution of SF strengthening to work hardening during deformation is not well understood; as compared to dislocation slip, twinning induced plasticity (TWIP) and TRIP. Thus, we used in-situ neutron diffraction to correlate SF strengthening to work hardening behavior in a low SFE Fe40Mn20Cr15Co20Si5 (at%) high entropy alloy, SFE ~ 6.31 mJ m−2. Cooperative activation of multiple mechanisms was indicated by increases in SF strengthening and γ-f.c.c. → ε-h.c.p. transformation leading to a simultaneous increase in strength and ductility. The present study demonstrates the application of in-situ, neutron or X-ray, diffraction techniques to correlating SF strengthening to work hardening.

scholarly journals Cutting Edge of High-Entropy Alloy Superconductors from the Perspective of Materials Research

Metals ◽  
2020 ◽  
Vol 10 (8) ◽  
pp. 1078
Author(s):  
Jiro Kitagawa ◽  
Shusuke Hamamoto ◽  
Naoki Ishizu
Keyword(s):  
Material Design ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
Simple Material ◽  
Σ Phase ◽  
High Entropy ◽  
Cscl Type ◽  
Materials Research ◽  
Face Centered ◽  
New Phenomena

High-entropy alloys (HEAs) are a new class of materials which are being energetically studied around the world. HEAs are characterized by a multicomponent alloy in which five or more elements randomly occupy a crystallographic site. The conventional HEA concept has developed into simple crystal structures such as face-centered-cubic (fcc), body-centered-cubic (bcc) and hexagonal-closed packing (hcp) structures. The highly atomic-disordered state produces many superior mechanical or thermal properties. Superconductivity has been one of the topics of focus in the field of HEAs since the discovery of the bcc HEA superconductor in 2014. A characteristic of superconductivity is robustness against atomic disorder or extremely high pressure. The materials research on HEA superconductors has just begun, and there are open possibilities for unexpectedly finding new phenomena. The present review updates the research status of HEA superconductors. We survey bcc and hcp HEA superconductors and discuss the simple material design. The concept of HEA is extended to materials possessing multiple crystallographic sites; thus, we also introduce multisite HEA superconductors with the CsCl-type, α-Mn-type, A15, NaCl-type, σ-phase and layered structures and discuss the materials research on multisite HEA superconductors. Finally, we present the new perspectives of eutectic HEA superconductors and gum metal HEA superconductors.

scholarly journals Dynamic deformation behavior of a face-centered cubic FeCoNiCrMn high-entropy alloy

2018 ◽  
Vol 63 (6) ◽  
pp. 362-368 ◽  
Author(s):  
Junyang He ◽  
Qi Wang ◽  
Husheng Zhang ◽  
Lanhong Dai ◽  
Toshiji Mukai ◽  
...  
Keyword(s):  
Deformation Behavior ◽  
Dynamic Deformation ◽  
High Entropy Alloy ◽  
Face Centered Cubic ◽  
High Entropy ◽  
Dynamic Deformation Behavior ◽  
Face Centered

scholarly journals Effect of Mn Addition on the Microstructures and Mechanical Properties of CoCrFeNiPd High Entropy Alloy

Entropy ◽  
2019 ◽  
Vol 21 (3) ◽  
pp. 288
Author(s):  
Yiming Tan ◽  
Jinshan Li ◽  
Jun Wang ◽  
Hongchao Kou
Keyword(s):  
Intermetallic Compound ◽  
Interface Energy ◽  
High Entropy Alloy ◽  
Strengthening Effect ◽  
Face Centered Cubic ◽  
Liquid Interfaces ◽  
High Entropy ◽  
Single Face ◽  
Face Centered ◽  
Fcc Phase

CoCrFeNiPdMnx (x = 0, 0.2, 0.4, 0.6, 0.8) high entropy alloys (HEAs) were prepared and characterized. With an increase in Mn addition, the microstructures changed from dendrites (CoCrFeNiPd with a single face-centered-cubic (FCC) phase) to divorced eutectics (CoCrFeNiPdMn0.2 and CoCrFeNiPdMn0.4), to hypoeutectic microstructures (CoCrFeNiPdMn0.6), and finally to seaweed eutectic dendrites (CoCrFeNiPdMn0.8). The addition of Mn might change the interface energy anisotropy of both the FCC/liquid and MnPd-rich intermetallic compound/liquid interfaces, thus forming the seaweed eutectic dendrites. The hardness of the FCC phase was found to be highly related to the solute strengthening effect, the formation of nanotwins and the transition from CoCrFeNiPd-rich to CoCrFeNi-rich FCC phase. Hierarchical nanotwins were found in the MnPd-rich intermetallic compound and a decrease in either the spacing of primary twins or secondary twins led to an increase in hardness. The designing rules of EHEAs were discussed and the pseudo binary method was revised accordingly.

Sign in / Sign up

Export Citation Format

Share Document