scholarly journals Coherent Precipitation and Strengthening in Compositionally Complex Alloys: A Review

Entropy ◽  
2018 ◽  
Vol 20 (11) ◽  
pp. 878 ◽  
Author(s):  
Qing Wang ◽  
Zhen Li ◽  
Shujie Pang ◽  
Xiaona Li ◽  
Chuang Dong ◽  
...  
Keyword(s):  
Solid Solution ◽  
High Performance ◽  
Particle Morphology ◽  
Precipitation Strengthening ◽  
Second Phase ◽  
High Entropy ◽  
Second Phase Particles ◽  
Alloy Strength ◽  
Solid Solution Matrix ◽  
The Relationship

High-performance conventional engineering materials (including Al alloys, Mg alloys, Cu alloys, stainless steels, Ni superalloys, etc.) and newly-developed high entropy alloys are all compositionally-complex alloys (CCAs). In these CCA systems, the second-phase particles are generally precipitated in their solid-solution matrix, in which the precipitates are diverse and can result in different strengthening effects. The present work aims at generalizing the precipitation behavior and precipitation strengthening in CCAs comprehensively. First of all, the morphology evolution of second-phase particles and precipitation strengthening mechanisms are introduced. Then, the precipitation behaviors in diverse CCA systems are illustrated, especially the coherent precipitation. The relationship between the particle morphology and strengthening effectiveness is discussed. It is addressed that the challenge in the future is to design the stable coherent microstructure in different solid-solution matrices, which will be the most effective approach for the enhancement of alloy strength.

Effect of Bi Addition on the Corrosion Behavior of Zirconium Alloys

2013 ◽  
Author(s):  
M. Y. Yao ◽  
B. X. Zhou ◽  
Q. Li ◽  
W. P. Zhang ◽  
L. Zhu ◽  
...  
Keyword(s):  
Solid Solution ◽  
Corrosion Resistance ◽  
Corrosion Behavior ◽  
Mass Fraction ◽  
Zirconium Alloys ◽  
Deionized Water ◽  
Second Phase ◽  
Micro Structure ◽  
Second Phase Particles ◽  
Structure Observation

In order to investigate systematically the effect of Bi addition on the corrosion resistance of zirconium alloys, different zirconium-based alloys, including Zr-4 (Zr-1.5Sn-0.2Fe-0.1Cr), S5 (Zr-0.8Sn-0.35Nb-0.4Fe-0.1Cr), T5 (Zr-0.7Sn-1.0Nb-0.3Fe-0.1Cr) and Zr-1Nb, were adopted to prepare the zirconium alloys containing Bi of 0∼0.5% in mass fraction. These alloys were denoted as Zr-4+xBi, S5+xBi, T5+xBi and Zr-1Nb+xBi, respectively. The corrosion behavior of these specimens was investigated by autoclave testing in lithiated water with 0.01 M LiOH or deionized water at 360°C/18.6 MPa and in superheated steam at 400 °C/10.3 MPa. The micro structure of the alloys was examined by TEM and the second phase particles (SPPs) were analyzed by EDS. Micro structure observation shows that the addition of Bi promotes the precipitation of Sn as second phase particles (SPPs) because Sn is in solid solution in α-Zr matrix in Zr-4, S5 and T5 alloys. The concentration of Bi dissolved in α-Zr matrix increase with the increase of Nb in the alloys, and the excess Bi precipitates as Bi-containing SPPs. The corrosion results show that the effect of Bi addition on the corrosion behavior of different zirconium-based alloys is very complicated, depending on their compositions and corrosion conditions. In the case of higher Bi concentration in α-Zr, the zirconium alloys exhibit better corrosion resistance. However, in the case of precipitation of Bi-containing SPPs, the corrosion resistance gets worse. This indicates that the solid solution of Bi in α-Zr matrix can improve the corrosion resistance, while the precipitation of the Bi-containing SPPs is harmful to the corrosion resistance.

scholarly journals Alloying and Processing Effects on the Microstructure, Mechanical Properties, and Degradation Behavior of Extruded Magnesium Alloys Containing Calcium, Cerium, or Silver

Materials ◽  
2020 ◽  
Vol 13 (2) ◽  
pp. 391 ◽  
Author(s):  
Jan Bohlen ◽  
Sebastian Meyer ◽  
Björn Wiese ◽  
Bérengère J. C. Luthringer-Feyerabend ◽  
Regine Willumeit-Römer ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Magnesium Alloys ◽  
Processing Parameters ◽  
Second Phase ◽  
Degradation Behavior ◽  
Microstructure Development ◽  
Corrosion Properties ◽  
Second Phase Particles ◽  
Degradation Rates ◽  
The Relationship

Magnesium alloys attract attention as degradable implant materials due to their adjustable corrosion properties and biocompatibility. In the last few decades, especially wrought magnesium alloys with enhanced mechanical properties have been developed, with the main aim of increasing ductility and formability. Alloying and processing studies allowed demonstrating the relationship between the processing and the microstructure development for many new magnesium alloys. Based on this experience, magnesium alloy compositions need adjustment to elements improving mechanical properties while being suitable for biomaterial applications. In this work, magnesium alloys from two Mg-Zn series with Ce (ZE) or Ca (ZX) as additional elements and a series of alloys with Ag and Ca (QX) as alloying elements are suggested. The microstructure development was studied after the extrusion of round bars with varied processing parameters and was related to the mechanical properties and the degradation behavior of the alloys. Grain refinement and texture weakening mechanisms could be improved based on the alloy composition for enhancing the mechanical properties. Degradation rates largely depended on the nature of second phase particles rather than on the grain size, but remained suitable for biological applications. Furthermore, all alloy compositions exhibited promising cytocompatibility.

Cooling Process for Precipitation Strengthening of Vanadium in Ferrite

2012 ◽  
Vol 706-709 ◽  
pp. 2078-2083
Author(s):  
Xiao Hui Cai ◽  
Zhen Yu Liu ◽  
Guo Dong Wang
Keyword(s):  
Solid Solution ◽  
Nitrogen Content ◽  
Dislocation Line ◽  
Precipitation Strengthening ◽  
Solution Temperature ◽  
Precipitation Process ◽  
Cooling Process ◽  
Coiling Temperature ◽  
Parabolic Curve ◽  
The Relationship

The precipitation of vanadium takes place mainly in ferrite by interphase precipitation or nucleation on dislocation line, which makes sense for the industry production due to the precipitation strengthening. The objective is to analysize the cooling process of V-steels to exert the precipitation strengthening of vanadium. The steels with 0.09%C-0.055%N/0.0107%N/0.0168%N/0.0193%N-0.08%V/0.085V steel are the researched steel grades. Using solid solubility products model and thermodynamic equation, the full solid solution temperature, nucleation rate curve and PTT curve of precipitation process are calculated. The effect of nitrogen on the precipitation behaviour of V(C,N) in γ and the precipitation of V(C,N) in α are simulated. Based on the calculation results the trial process is determined. The laboratorial trials are carried out with ultra fast cooling. The precipitate particles are observed by TEM. The solid solution amount increases monotonously and the size of precipitate particle decreases with the nitrogen content. The solid solution temperature of 0.055%N, 0.0107%N, 0.0168%N and 0.0193%N are 977.0°C, 1028.0°C, 1062.3 and 1078.9°C respectively. The laboratorial trial results shows that the tensile strength is improved about 100 MPa due to the precipitation strengthening. The relationship between the coiling temperature and the strength is parabolic curve downward and the relationship between the coiling temperature and the elongation is parabolic curve upward. This calculation can determine both the proper nitrogen content and the optimal cooling process. The trial results proves this method is feasible and efficiency.

Microstructure and Properties of Alloys with Equal Atomic Principal Components

2013 ◽  
Vol 765-767 ◽  
pp. 3143-3146
Author(s):  
Yan Ping Wang ◽  
Yu Zhuang ◽  
Jian Chen Li
Keyword(s):  
Solid Solution ◽  
Principal Components ◽  
Argon Atmosphere ◽  
Second Phase ◽  
High Entropy Alloys ◽  
Arc Furnace ◽  
Phase Precipitation ◽  
High Entropy ◽  
Bcc Structure ◽  
Fcc Structure

Four high-entropy alloys are prepared by an arc furnace under argon atmosphere. The microstructure and the properties of the alloys are investigated. The results show that NiCrCuCoFe alloy consists of a single FCC solid solution. When Al presents in the alloys, the microstructures of the alloys change to a BCC+ FCC solid solution. It is indicated that Al element promotes the formation of BCC solid solution, and Si and Mn promote the formation of complicated compounds. The hardness of alloys with BCC structure is higher than that of the alloys with FCC structure. The complicated compounds are formed, the hardness increases further. The highest hardness of the alloys reaches 882 HV due to the strengthening of the second phase precipitation.

scholarly journals Severe Plastic Deformation and Phase Transformations in High Entropy Alloys: A Review

Crystals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 54
Author(s):  
Boris B. Straumal ◽  
Roman Kulagin ◽  
Brigitte Baretzky ◽  
Natalia Yu. Anisimova ◽  
Mikhail V. Kiselevskiy ◽  
...  
Keyword(s):  
Solid Solution ◽  
Plastic Deformation ◽  
Severe Plastic Deformation ◽  
Phase Transformations ◽  
Single Phase ◽  
Materials Science ◽  
Bulk Solution ◽  
Second Phase ◽  
High Entropy Alloys ◽  
High Entropy

This review discusses an area of expertise that is at the intersection of three large parts of materials science. These are phase transformations, severe plastic deformation (SPD), and high-entropy alloys (HEA). First, SPD makes it possible to determine the borders of single-phase regions of existence of a multicomponent solid solution in HEAs. An important feature of SPD is that using these technologies, it is possible to obtain second-phase nanoparticles included in a matrix with a grain size of several tens of nanometers. Such materials have a very high specific density of internal boundaries. These boundaries serve as pathways for accelerated diffusion. As a result of the annealing of HEAs subjected to SPD, it is possible to accurately determine the border temperature of a single-phase solid solution area on the multicomponent phase diagram of the HEA. Secondly, SPD itself induces phase transformations in HEAs. Among these transformations is the decomposition of a single-phase solid solution with the formation of nanoparticles of the second phase, the formation of high-pressure phases, amorphization, as well as spinodal decomposition. Thirdly, during SPD, a large number of new grain boundaries (GBs) are formed due to the crystallites refinement. Segregation layers exist at these new GBs. The concentration of the components in GBs differs from that in the bulk solid solution. As a result of the formation of a large number of new GBs, atoms leave the bulk solution and form segregation layers. Thus, the composition of the solid solution in the volume also changes. All these processes make it possible to purposefully influence the composition, structure and useful properties of HEAs, especially for medical applications.

scholarly journals Compositional Optimization of High-Performance Ferritic (HiperFer) Steels—Effect of Niobium and Tungsten Content

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1300
Author(s):  
Xiuru Fan ◽  
Bernd Kuhn ◽  
Jana Pöpperlová ◽  
Wolfgang Bleck ◽  
Ulrich Krupp
Keyword(s):  
Solid Solution ◽  
High Performance ◽  
Laves Phase ◽  
Process Industry ◽  
Creep Testing ◽  
Power Engineering ◽  
Precipitation Strengthening ◽  
Tungsten Content ◽  
Structural Application ◽  
And Tungsten

The combined addition of Nb and W provides increased solid solution and precipitation strengthening by (Fe,Cr,Si)2(Nb,W)-Laves phase particles of ferritic, 17 wt.% Cr stainless high-performance ferritic (HiperFer) steel. Based on alloy modifications and the obtained hardness, tensile, and creep testing results; a new high alloying variant is proposed as a candidate steel for future structural application up to approximately 680 °C in power engineering and the process industry.

scholarly journals Strengthening Mechanisms in CoCrFeNiX0.4 (Al, Nb, Ta) High Entropy Alloys Fabricated by Powder Plasma Arc Additive Manufacturing

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 721
Author(s):  
Yupeng Zhang ◽  
Qingkai Shen ◽  
Xizhang Chen ◽  
Subramanian Jayalakshmi ◽  
Ramachandra Arvind Singh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Atomic Radius ◽  
Eutectic Structure ◽  
Precipitation Strengthening ◽  
High Entropy Alloys ◽  
Plasma Arc ◽  
High Entropy ◽  
Solid Solution Strengthening ◽  
Solution Strengthening

In high entropy alloys (HEAs), the addition of large-size atoms results in lattice distortion and further leads to solid solution strengthening or precipitation strengthening. However, the relationship between atomic radius, solid solution strengthening and precipitation strengthening has not been discerned yet. In this work, CoCrFeNiX0.4 (X = Al, Nb, Ta, with an equi-atomic radius) HEAs were prepared by powder plasma arc additive manufacturing (PPA-AM) and evaluated for their mechanical properties. Compression and nano-indentation hardness tests showed that the HEA with Ta showed the best properties. The influence of atomic radius and solid solubility on solid solution strengthening was investigated and the main strengthening mechanism that determines the mechanical properties of the developed HEAs was analyzed. The results showed that (i) the CoCrFeNiAl0.4 alloy did not show any solid solution strengthening effect and that a clear relation between solid solution strengthening and atomic size was not observed; (ii) in both CoCrFeNiTa0.4 and CoCrFeNiNb0.4 HEAs, precipitation strengthening and grain boundary strengthening effects are observed, wherein the difference in mechanical properties between both the alloys can be mainly attributed to the formation of fine eutectic structure in CoCrFeNiTa0.4; and (iii) from the microstructural analyses, it was identified that, in the CoCrFeNiTa0.4 HEA, the location containing a fine eutectic structure is accompanied by the formation of low-angle grain boundaries (LAGBs), which is also the region where deformed grains gather, giving rise to improved mechanical strengthening.

Sign in / Sign up

Export Citation Format

Share Document