scholarly journals A CMOS Transmitter Analog Baseband for 5G Mobile Communication

Electronics ◽  
2019 ◽  
Vol 8 (11) ◽  
pp. 1319
Author(s):  
Yen ◽  
Chen ◽  
Wei ◽  
Chung
Keyword(s):  
Mobile Communication ◽  
Gain Control ◽  
Cmos Technology ◽  
Control Technique ◽  
Constant Current ◽  
Constant Current Density ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Analog Baseband ◽  
5G Mobile Communication

CMOS analog baseband circuits including a low-pass filter (LPF) and a programmable gain amplifier (PGA) are designed and implemented for the fifth-generation (5G) mobile communication. The super source follower topology is adopted to achieve a wideband LPF with good linearity, while the constant current density gain control technique is used to implement gain cells of the PGA. The circuits are integrated as an analog baseband for a 5G transmitter (TX) and fabricated using TSMC 90-nm CMOS technology. The analog baseband exhibits the bandwidth from 1.03 to 1.05 GHz when the voltage gain is varied from −18.9 dB to 3.8 dB in 1-dB steps. The gain step errors are within −0.7 dB to 0.9 dB. In the highest gain mode, the analog baseband achieves the IP1dB of −10 dBv and the IIP3 of −0.2 dBv. Over the band of interest, the NF of the analog baseband is 24.4–40.0 dB.

60 GHz-Band Low-Noise Amplifier

2017 ◽  
Vol 26 (05) ◽  
pp. 1750075 ◽  
Author(s):  
Najam Muhammad Amin ◽  
Lianfeng Shen ◽  
Zhi-Gong Wang ◽  
Muhammad Ovais Akhter ◽  
Muhammad Tariq Afridi
Keyword(s):  
Transmission Line ◽  
Quality Factor ◽  
Noise Figure ◽  
Cmos Technology ◽  
Low Noise ◽  
Constant Current ◽  
60 Ghz ◽  
Frequency Range ◽  
Constant Current Density ◽  
Chip Area

This paper presents the design of a 60[Formula: see text]GHz-band LNA intended for the 63.72–65.88[Formula: see text]GHz frequency range (channel-4 of the 60[Formula: see text]GHz band). The LNA is designed in a 65-nm CMOS technology and the design methodology is based on a constant-current-density biasing scheme. Prior to designing the LNA, a detailed investigation into the transistor and passives performances at millimeter-wave (MMW) frequencies is carried out. It is shown that biasing the transistors for an optimum noise figure performance does not degrade their power gain significantly. Furthermore, three potential inductive transmission line candidates, based on coplanar waveguide (CPW) and microstrip line (MSL) structures, have been considered to realize the MMW interconnects. Electromagnetic (EM) simulations have been performed to design and compare the performances of these inductive lines. It is shown that the inductive quality factor of a CPW-based inductive transmission line ([Formula: see text] is more than 3.4 times higher than its MSL counterpart @ 65[Formula: see text]GHz. A CPW structure, with an optimized ground-equalizing metal strip density to achieve the highest inductive quality factor, is therefore a preferred choice for the design of MMW interconnects, compared to an MSL. The LNA achieves a measured forward gain of [Formula: see text][Formula: see text]dB with good input and output impedance matching of better than [Formula: see text][Formula: see text]dB in the desired frequency range. Covering a chip area of 1256[Formula: see text][Formula: see text]m[Formula: see text]m including the pads, the LNA dissipates a power of only 16.2[Formula: see text]mW.

scholarly journals Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters

Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2931
Author(s):  
Waldemar Jendernalik ◽  
Jacek Jakusz ◽  
Grzegorz Blakiewicz
Keyword(s):  
Dynamic Range ◽  
Low Voltage ◽  
Supply Voltage ◽  
Low Frequency ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Biomedical Sensors ◽  
Filter Synthesis ◽  
Cascade Method

Buffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more general method for buffer-based filter synthesis is developed and presented. The method uses RLC ladder prototypes to obtain filters of arbitrary orders. In addition, a set of novel circuit solutions with ultra-low voltage and power are proposed. The introduced circuits were synthesized and simulated using 180-nm CMOS technology of X-FAB. One of the designed circuits is a fourth-order, low-pass filter that features: 100-Hz passband, 0.4-V supply voltage, power consumption of less than 5 nW, and dynamic range above 60 dB. Moreover, the total capacitance of the proposed filter (31 pF) is 25% lower compared to the structure synthesized using a conventional cascade method (40 pF).

Neural mechanisms of adaptive gain control in a joint control loop: muscle force and motoneuronal activity

1997 ◽  
Vol 200 (9) ◽  
pp. 1383-1402 ◽  
Author(s):  
R Kittmann
Keyword(s):  
Muscle Force ◽  
Gain Control ◽  
Open Loop ◽  
Chordotonal Organ ◽  
Joint Control ◽  
Modulation Amplitude ◽  
Control Loop ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Change In Mean

An adaptive gain control system of a proprioceptive feedback system, the femur­tibia control loop, is investigated. It enables the joint control loop to work with a high gain but it prevents instability oscillations. In the inactive stick insect, the realisation of specific changes in gain is described for tibial torque, for extensor tibiae muscle force and for motoneuronal activity. In open-loop experiments, sinusoidal stimuli are applied to the femoral chordotonal organ (fCO). Changes in gain that depend on fCO stimulus parameters (such as amplitude, frequency and repetition rate), are investigated. Furthermore, spontaneous and touch-induced changes in gain that resemble the behavioural state of the animal are described. Changes in gain in motoneurones are always realised as changes in the amplitude of modulation of their discharge frequency. Nevertheless, depending on the stimulus situation, two different mechanisms underlie gain changes in motoneurones. (i) Changes in gain can be based on changes in the strength of the sensorimotor pathways that transmit stimulus-modulated information from the fCO to the motoneurones. (ii) Changes in gain can be based on changes in the mean activity of a motoneurone by means of its spike threshold: when, during the modulation, the discharge of a motoneurone is inhibited for part of the stimulus cycle, then a change in mean activity subsequently causes a change in modulation amplitude and gain. A new neuronal mechanism is described that helps to compensate the low-pass filter characteristics of the muscles by an increased activation, especially by a sharper distribution of spikes in the stimulus cycle at high fCO stimulus frequencies.

THE DIFFERENTIAL DIFFERENCE OPERATIONAL FLOATING AMPLIFIER: NEW CMOS REALIZATIONS AND APPLICATIONS

2009 ◽  
Vol 18 (07) ◽  
pp. 1287-1308 ◽  
Author(s):  
EMAN A. SOLIMAN ◽  
SOLIMAN A. MAHMOUD
Keyword(s):  
Analog Circuits ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Variable Gain Amplifiers ◽  
Variable Gain ◽  
Fully Differential ◽  
Filter Performance ◽  
Low Pass ◽  
Band Pass

This paper presents different novel CMOS realizations for the differential difference operational floating amplifier (DDOFA). The DDOFA was first introduced in Ref. 1 and was used to realize different analog circuits like integrators, filters and variable gain amplifiers. New CMOS realizations for the DDOFA are introduced in this literature. Furthermore the DDOFA is modified to realize a fully differential current conveyor (FDCC). Novel CMOS realizations of the FDCC are presented. The FDCC is used to realize second-order band pass–low-pass filter. Performance comparisons between the different realizations of the DDOFA and FDCC are given in this literature. PSPICE simulations of the overall proposed circuits are given using 0.25 μm CMOS Technology from TMSC MOSIS model and dual supply voltages of ±1.5 V.

scholarly journals A CMOS Low Pass Filter for SoC Lock-in-Based Measurement Devices

Sensors ◽  
2019 ◽  
Vol 19 (23) ◽  
pp. 5173 ◽  
Author(s):  
Jorge Pérez-Bailón ◽  
Belén Calvo ◽  
Nicolás Medrano
Keyword(s):  
Dynamic Range ◽  
Current Trend ◽  
Cutoff Frequency ◽  
Oxide Semiconductor ◽  
Constant Current ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Compact Size ◽  
Low Pass ◽  
Lock In

This paper presents a fully integrated Gm–C low pass filter (LPF) based on a current steering Gm reduction-tuning technique, specifically designed to operate as the output stage of a SoC lock-in amplifier. To validate this proposal, a first-order and a second-order single-ended topology were integrated into a 1.8 V to 0.18 µm CMOS (Complementary Metal-Oxide-Semiconductor) process, showing experimentally a tuneable cutoff frequency that spanned five orders of magnitude, from tens of mHz to kHz, with a constant current consumption (below 3 µA/pole), compact size (<0.0140 mm2/pole), and a dynamic range better than 70 dB. Compared to state-of-the-art solutions, the proposed approach exhibited very competitive performances while simultaneously fully satisfying the demanding requirements of on-chip portable measurement systems in terms of highly efficient area and power. This is of special relevance, taking into account the current trend towards multichannel instruments to process sensor arrays, as the total area and power consumption will be proportional to the number of channels.

scholarly journals Floating Active Inductor Based Trans-Impedance Amplifier in 0.18 μm CMOS Technology for Optical Applications

Electronics ◽  
2019 ◽  
Vol 8 (12) ◽  
pp. 1547
Author(s):  
Xiangyu Chen ◽  
Yasuhiro Takahashi
Keyword(s):  
Power Dissipation ◽  
Supply Voltage ◽  
Cmos Technology ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Chip Area ◽  
Active Inductors ◽  
Low Pass ◽  
Optical Applications ◽  
Fifth Order

In this paper, a transimpedance amplifier (TIA) based on floating active inductors (FAI) is presented. Compared with conventional TIAs, the proposed TIA has the advantages of a wider bandwidth, lower power dissipation, and smaller chip area. The schematics and characteristics of the FAI circuit are explained. Moreover, the proposed TIA employs the combination of capacitive degeneration, the broadband matching network, and the regulated cascode input stage to enhance the bandwidth and gain. This turns the TIA design into a fifth-order low pass filter with Butterworth response. The TIA is implemented using 0.18 μ m Rohm CMOS technology and consumes only 10.7 mW with a supply voltage of 1.8 V. When used with a 150 fF photodiode capacitance, it exhibits the following characteristics: gain of 41 dB Ω and −3 dB frequency of 10 GHz. This TIA occupies an area of 180 μ m × 118 μ m.

Design of a Sine Sweeping Constant Current Source Based FPGA and DDS

2014 ◽  
Vol 936 ◽  
pp. 2230-2234
Author(s):  
Ya Ping Yu ◽  
Hui Zhao ◽  
Yuan Liu ◽  
Ren Jie Yang ◽  
Gui Mei Dong ◽  
...  
Keyword(s):  
Frequency Control ◽  
Current Source ◽  
Sine Wave ◽  
Constant Current ◽  
Constant Current Source ◽  
Pass Filter ◽  
Low Pass Filter ◽  
Low Pass ◽  
Fpga Chip ◽  
Sine Wave Generator

This paper designed a range of 0.1 ~ 250 kHz sine wave sweeping constant current source, which sine wave generator based on FPGA chip and DDS technology, the desired sine wave frequency was obtained by controlling the frequency control words. Low-pass filter circuit was realized by using the LTC1560-1, conversion circuit from the voltage to the current was consisted of a Howland current pump. The constant current source shows a good spectral impedance purity and amplitude.

scholarly journals A fast L1 adaptive constrained back-stepping controller using barrier Lyapunov function for anuncertain submersible vehicle

2021 ◽  
Author(s):  
Hossein Ahmadian ◽  
Mehdi Arefi ◽  
Alireza Khayatian ◽  
Allahyar Montazeri
Keyword(s):  
Adaptive Control ◽  
Lyapunov Function ◽  
Trajectory Tracking ◽  
Tracking Error ◽  
Control Technique ◽  
Remotely Operated Vehicle ◽  
Pass Filter ◽  
Low Pass Filter ◽  
L1 Adaptive Control ◽  
Barrier Lyapunov Function

Abstract In this paper, a new L1 adaptive back-stepping controller based on the barrier Lyapunov function (BLF) is proposed to respect the position and velocity constraints usually imposed in designing Euler-Lagrange systems. The purpose of this investigation is to improve different aspects of a conventional L1 adaptive control. More specifically, the modified controller has a lower complexity by removing the low-pass filter from the design procedure. The performance of the controller is also enhanced by having a faster convergence speed and increased robustness against nonlinear uncertainties and disturbances arising in practical applications. The proposed scheme is evaluated on two different Euler-Lagrange systems, i.e. a 6-DOF remotely operated vehicle (ROV) and a single-link manipulator. The results for the new back-stepping design are assessed in both scenarios in terms of settling time, percentage of overshoot, and trajectory tracking error. The results confirm that both tracking and state estimation errors for position and velocity outputs outperform the standard L1 adaptive control technique. The results also demonstrate the high performance of the proposed approach in removing the matched nonlinear time-varying disturbances and dynamic uncertainties and a good trajectory tracking despite the uncertainty on the input gain of the system.

Sign in / Sign up

Export Citation Format

Share Document