scholarly journals Multiband Dual-Meander Line Antenna for Body-Centric Networks’ Biomedical Applications by Using UMC 180 nm

Electronics ◽  
2020 ◽  
Vol 9 (9) ◽  
pp. 1350
Author(s):  
Heba Shawkey ◽  
Dalia Elsheakh
Keyword(s):  
Biomedical Applications ◽  
Impedance Bandwidth ◽  
Antenna Structure ◽  
High Data ◽  
High Frequency Structure Simulator ◽  
On Chip Antenna ◽  
Integration Effect ◽  
Operating Bandwidth ◽  
On Chip ◽  
Meander Line

A new, compact, on-chip antenna architecture for 5G body-centric networks’ (BCNs) applications is presented in this paper. The integrated antenna combines two turns of dual-meander lines (DML) on two stacked layers and a metal ground layer. The proposed DML antenna structure operated at resonant bands 22 GHz, 34 GHz, 44 GHz, and 58 GHz with an operating bandwidth up to 2 GHz at impedance bandwidth ≤−7.5 dB (VSWR—Voltage Standing Wave Ratio ≤ 2.5) and antenna gain about −20 dBi, −15 dBi, −10 dBi, and −1 dBi, respectively. Then it was compared with conventional single-meander line antenna. The proposed structure decreased the resonant frequency by 22%, increased number of tuning bands, and broadened the operating bandwidth by 25%, 15%, 10%, and 20% for the tuning bands to be a suitable choice for high-data -ate biomedical applications. Furthermore, the proposed antenna was simulated and studied for its performance on and inside the human body to test the integration effect in wearable equipment. The results showed that the antenna had acceptable performance in both locations. All simulations of the proposed antenna were done were done by using Ansys HFSS (high-frequency structure simulator) v.15 (Ansys, Canonsburg, PA, USA). The DML (Digital Microwave Links) antenna was fabricated by using UMC (United Microelectronics Corporation) 180 nm CMOS (Complementary Metal–Oxidesemi–Conductor) technology with a total area of 1150 µm × 200 µm and the results showed a good agreement between measured and simulated results.

scholarly journals Study on on-Chip Antenna Design Based on Metamaterial-Inspired and Substrate-Integrated Waveguide Properties for Millimetre-Wave and THz Integrated-Circuit Applications

2020 ◽  
Author(s):  
Mohammad Alibakhshikenari ◽  
Bal S. Virdee ◽  
Ayman Abdulhadi Althuwayb ◽  
Sonia Aïssa ◽  
Chan H. See ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Ground Plane ◽  
Silicon Layer ◽  
Bottom Surface ◽  
Impedance Bandwidth ◽  
Substrate Integrated Waveguide ◽  
Millimetre Wave ◽  
Antenna Structure ◽  
On Chip Antenna ◽  
On Chip

Abstract This paper presents the results of a study on improving the performance parameters such as the impedance bandwidth, radiation gain and efficiency, as well as suppressing substrate loss of an innovative antenna for on-chip implementation for millimetre-wave and terahertz integrated-circuits. This was achieved by using the metamaterial and the substrate-integrated waveguide (SIW) technologies. The on-chip antenna structure comprises five alternating layers of metallization and silicon. An array of circular radiation patches with metamaterial-inspired crossed-shaped slots are etched on the top metallization layer below which is a silicon layer whose bottom surface is metalized to create a ground plane. Implemented in the silicon layer below is a cavity above which is no ground plane. Underneath this silicon layer is where an open-ended microstrip feedline is located which is used to excite the antenna. The feed mechanism is based on the coupling of the electromagnetic energy from the bottom silicon layer to the top circular patches through the cavity. To suppress surface waves and reduce substrate loss, the SIW concept is applied at the top silicon layer by implementing the metallic via holes at the periphery of the structure that connect the top layer to the ground plane. The proposed on-chip antenna has an average measured radiation gain and efficiency of 6.9 dBi and 53%, respectively, over its operational frequency range from 0.285–0.325 THz. The proposed on-chip antenna has dimensions of 1.35 × 1 × 0.06 mm3. The antenna is shown to be viable for applications in millimetre-waves and terahertz integrated-circuits.

scholarly journals A Low-Profile High-Gain and Wideband Log-Periodic Meandered Dipole Array Antenna with a Cascaded Multi-Section Artificial Magnetic Conductor Structure

Sensors ◽  
2019 ◽  
Vol 19 (20) ◽  
pp. 4404 ◽  
Author(s):  
Son Trinh-Van ◽  
Oh Heon Kwon ◽  
Euntae Jung ◽  
Jinwoo Park ◽  
Byunggil Yu ◽  
...  
Keyword(s):  
High Gain ◽  
Operating Frequency ◽  
Main Beam ◽  
Impedance Bandwidth ◽  
Beam Direction ◽  
Magnetic Conductor ◽  
Artificial Magnetic Conductor ◽  
Low Profile ◽  
Operating Bandwidth ◽  
Meander Line

This paper presents a low-profile log-periodic meandered dipole array (LPMDA) antenna with wideband and high gain characteristics. The antenna consists of 14 dipole elements. For compactness, a meander line structure is applied to each dipole element to reduce its physical length. As a result, a compact and wideband LPMDA antenna is realized, exhibiting a wide impedance bandwidth of 1.04–5.22 GHz (ratio bandwidth of 5.02:1) for | S 11| < −10 dB. To enhance the antenna gain performance while maintaining the wideband behavior, the LPMDA antenna is integrated with a new design of an artificial magnetic conductor (AMC) structure. The designed AMC is realized by combining three AMC structures of different sizes to form a cascaded multi-section AMC structure, of which its overall operating bandwidth can continuously cover the entire impedance bandwidth of the LPMDA antenna. The proposed AMC-backed LPMDA antenna is experimentally verified and its measured −10 dB reflection bandwidth is found to be in the range of 0.84–5.15 GHz (6.13:1). At the main beam direction within the operating frequency bandwidth, the gain of the proposed AMC-backed LPMDA antenna ranges from 7.15–11.43 dBi, which is approximately 4 dBi higher than that of an LPMDA antenna without an AMC. Moreover, the proposed antenna has a low profile of only 0.138 λ L. ( λ L is the free-space wavelength at the lowest operating frequency).

CPW-Fed Wide Band Micro-machined Fractal Antenna with Band-notched Function

2020 ◽  
Vol 35 (8) ◽  
pp. 929-935
Author(s):  
Ashwini Kumar ◽  
Amar Pharwaha
Keyword(s):  
Integrated Circuits ◽  
Low Cost ◽  
Wide Band ◽  
Impedance Bandwidth ◽  
Fractal Antenna ◽  
Sierpinski Carpet ◽  
Antenna Structure ◽  
High Frequency Structure Simulator ◽  
Novel Structure ◽  
Sierpiński Carpet

In this paper, a straightforward yet effective design methodology to design wideband antenna with band notched characteristics has been proposed. Sierpinski carpet fractal geometry has been used to realize the antenna structure. Co-planar waveguide feed is used with a novel structure to achieve larger impedance bandwidth and band notching characteristics. Proposed antenna is designed using High Frequency Structure Simulator (HFSS) on a low cost FR4 substrate (ɛr=4.4) which resonates at three frequencies 1.51 GHz (1.19-2.06GHz), 6.53 GHz and 8.99 GHz (4.44-9.54 GHz) while a band is notched at 10.46 GHz (9.32-11.92 GHz). The proposed antenna has an electrical dimension of 0.36 λm× 0.24 λm, here λm is the wavelength with respect to lowest resonating frequency of the antenna. The resonating and radiation characteristics of the antenna are verified experimentally. Further, investigations are made to achieve easy integration of the antenna to the monolithic microwave integrated circuits. For that the antenna has been designed on micro-machined high index Silicon substrate which improve matching and gain of the antenna. The results of the micro-machined Sierpinski carpet fractal antenna are highly convincing over the conventional FR4 based antenna.

scholarly journals A CPW - Fed Octagonal Ring Shaped Wide Band Antenna for Wireless Applications

2018 ◽  
Vol 7 (3) ◽  
pp. 87-92 ◽  
Author(s):  
P. Khanna ◽  
A. Sharma ◽  
A. K. Singh ◽  
A. Kumar
Keyword(s):  
Microstrip Antenna ◽  
Return Loss ◽  
Ground Plane ◽  
Wide Band ◽  
Impedance Bandwidth ◽  
Wireless Applications ◽  
High Frequency Structure Simulator ◽  
High Impedance ◽  
Ring Antenna ◽  
Operating Bandwidth

A CPW – Fed octagonal ring shaped antenna for wideband operation is presented. The radiating patch of proposed octagonal ring antenna consists of symmetrical slot in place of conventional annular ring microstrip antenna. The ground plane consists of two rectangular slots, while the radiator and the ground plane are on same plane that utilizes the space available around the radiator. The proposed antenna is simulated through Ansoft’s High Frequency Structure Simulator (HFSS). Measured result shows balanced agreement with the simulated results. The prototype is taken with dimensions 47 mm × 47 mm × 1.6 mm that achieves good return loss, constant group delay and good radiation patterns over the entire operating bandwidth of 2.0 to 9.5 GHz (7.5 GHz). The proposed antenna achieves high impedance bandwidth of 130%. Thus, the proposed antenna is applicable for S and C band applications.

Quarter cylindrical dielectric resonator antenna in multi-element composite form for wideband applications

2016 ◽  
Vol 9 (3) ◽  
pp. 639-647
Author(s):  
Pinku Ranjan ◽  
Ravi Kumar Gangwar
Keyword(s):  
Experimental Investigation ◽  
High Frequency ◽  
Dielectric Resonator ◽  
Simulation Software ◽  
Impedance Bandwidth ◽  
Dielectric Resonator Antenna ◽  
Radiation Patterns ◽  
High Frequency Structure Simulator ◽  
Composite Form ◽  
Operating Bandwidth

A novel quarter cylindrical dielectric resonator antenna (q-CDRA) has been introduced by splitting four uniform quarters from a cylinder. q-CDRA has been designed and validated with theoretical analysis. Two and four element q-CDRAs have been proposed in composite forms through Ansoft high-frequency structure simulator simulation software and fabricated for experimental investigation. The input characteristics and radiation patterns of the proposed antennas have been studied through simulation and compared with the measured ones. The |S11| characteristics of the proposed antennas have been compared with each other. The four-element composite q-CDRA has wide impedance bandwidth (|S11| ≤ −10 dB) of 58.15% with monopole-like radiation pattern as compared with other q-CDRAs. The two and four elements q-CDRAs have symmetric monopole-like radiation patterns with linear polarization for whole operating bandwidth (4.5–8.6 GHz). The proposed composite q-CDRAs may find suitable applications in WLAN and WiMAX band.

scholarly journals A Compact Semi-Circular and Arc-Shaped Slot Antenna for Heterogeneous RF Front-Ends

Electronics ◽  
2019 ◽  
Vol 8 (10) ◽  
pp. 1123 ◽  
Author(s):  
Zebiri ◽  
Sayad ◽  
Elfergani ◽  
Iqbal ◽  
Mshwat ◽  
...  
Keyword(s):  
Wireless Local Area Network ◽  
Local Area Network ◽  
Personal Communication ◽  
Local Area ◽  
Dual Band ◽  
Slot Antenna ◽  
Impedance Bandwidth ◽  
Area Network ◽  
Antenna Structure ◽  
High Frequency Structure Simulator

In this paper, a new miniaturized compact dual-band microstrip slot antenna is presented. To achieve the dual-band characteristics, two adjunct partial arc-shaped small slots are joined to two main circular slots embedded in the ground of the antenna structure. With a reduced size of 30 × 28.5 × 0.8 mm3, the proposed antenna presents a dual-band characteristic. The design is optimized using a High Frequency Structure Simulator (HFSS) followed by experimental verifications. An impedance bandwidth, for S11≤10 dB, that covers the 1.8 GHz and 2.4 GHz bands is accomplished, which makes the proposed antenna basically suitable for hand-held devices and medical applications. More applications such as digital communication system (DCS) 1.71–1.88 GHz, personal communication services (PCS) 1.85–1.99 GHz, Universal and mobile telecommunications system UMTS 1.92–2.17 GHz, Bluetooth 2.4–2.5 GHz, and Wi-Fi 2.4–2.454 GHz, Industrial Scientific and Medical radio frequency (RF) band ISM-2.4 GHz, Wireless Local Area Network (WLAN-2.4)are possible by simply changing one of the geometrical antenna dimensions. The antenna is characterized by stable radiation patterns as well.

Sign in / Sign up

Export Citation Format

Share Document