scholarly journals Magnetic Positioning Technique Integrated with Near-Field Communication for Wireless EV Charging

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1081 ◽  
Author(s):  
Zhongnan Qian ◽  
Rui Yan ◽  
Zeqian Cheng ◽  
Jiande Wu ◽  
Xiangning He
Keyword(s):  
Relative Position ◽  
Data Transmission ◽  
Power Efficiency ◽  
Near Field ◽  
Three Dimensional ◽  
Secondary Coil ◽  
Power Transfer ◽  
Electric Vehicle Charging ◽  
Position Detection ◽  
Positioning Method

For wireless electric vehicle charging, the relative position of the primary and secondary coils has significant impacts on the transferred power, efficiency and leakage magnetic flux. In this paper, a magnetic positioning method using simultaneous power and data transmission (SWPDT) is proposed for power coil alignment. Four signal coils are installed on the primary coil to detect the secondary coil position. By measuring the positioning signal amplitudes from the four signal coils, the power coil relative position can be obtained. Moreover, all the communication needed in the positioning process can be satisfied well by SWPDT technology, and no extra radio frequency (RF) communication hardware is needed. The proposed positioning method can work properly both in power transfer online condition and in power transfer offline condition. Thus, a highly integrated wireless charging system is achieved, which features simultaneous power transfer, data transmission and position detection. A positioning experimental setup is built to verify the proposed method. The experimental results demonstrate that the positioning resolution can be maintained no lower than 1 cm in a 1060 mm × 900 mm elliptical region for a pair of 510 mm × 410 mm rectangular power coils. The three-dimensional positioning accuracy achieves up to 1 cm.

scholarly journals Biofuel-powered soft electronic skin with multiplexed and wireless sensing for human-machine interfaces

2020 ◽  
Vol 5 (41) ◽  
pp. eaaz7946 ◽  
Author(s):  
You Yu ◽  
Joanna Nassar ◽  
Changhao Xu ◽  
Jihong Min ◽  
Yiran Yang ◽  
...  
Keyword(s):  
Human Body ◽  
Power Efficiency ◽  
Near Field ◽  
Three Dimensional ◽  
Biofuel Cells ◽  
Physical Parameters ◽  
Power Intensity ◽  
Electronic Skin ◽  
Self Powered ◽  
Body Self

Existing electronic skin (e-skin) sensing platforms are equipped to monitor physical parameters using power from batteries or near-field communication. For e-skins to be applied in the next generation of robotics and medical devices, they must operate wirelessly and be self-powered. However, despite recent efforts to harvest energy from the human body, self-powered e-skin with the ability to perform biosensing with Bluetooth communication are limited because of the lack of a continuous energy source and limited power efficiency. Here, we report a flexible and fully perspiration-powered integrated electronic skin (PPES) for multiplexed metabolic sensing in situ. The battery-free e-skin contains multimodal sensors and highly efficient lactate biofuel cells that use a unique integration of zero- to three-dimensional nanomaterials to achieve high power intensity and long-term stability. The PPES delivered a record-breaking power density of 3.5 milliwatt·centimeter−2 for biofuel cells in untreated human body fluids (human sweat) and displayed a very stable performance during a 60-hour continuous operation. It selectively monitored key metabolic analytes (e.g., urea, NH4+, glucose, and pH) and the skin temperature during prolonged physical activities and wirelessly transmitted the data to the user interface using Bluetooth. The PPES was also able to monitor muscle contraction and work as a human-machine interface for human-prosthesis walking.

scholarly journals Single-Sided Near-Field Wireless Power Transfer by A Three-Dimensional Coil Array

Micromachines ◽  
2019 ◽  
Vol 10 (3) ◽  
pp. 200 ◽  
Author(s):  
Amirhossein Hajiaghajani ◽  
Seungyoung Ahn
Keyword(s):  
Magnetic Field ◽  
Printed Circuit Boards ◽  
Signal To Noise Ratio ◽  
Near Field ◽  
3D Structure ◽  
Three Dimensional ◽  
Power Transfer ◽  
Circuit Boards ◽  
Wireless Power ◽  
Halbach Arrays

Wirelessly powered medical microrobots are often driven or localized by magnetic resonance imaging coils, whose signal-to-noise ratio is easily affected by the power transmitter coils that supply the microrobot. A controlled single-sided wireless power transmitter can enhance the imaging quality and suppress the radiation leakage. This paper presents a new form of electromagnet which automatically cancels the magnetic field to the back lobes by replacing the traditional circular coils with a three-dimensional (3D) coil scheme inspired by a generalized form of Halbach arrays. It is shown that, along with the miniaturization of the transmitter system, it allows for improved magnetic field intensity in the target side. Measurement of the produced magnetic patterns verifies that the power transfer to the back lobe is 15-fold smaller compared to the corresponding distance on the main lobe side, whilst maintaining a powering efficiency similar to that of conventional planar coils. To show the application of the proposed array, a wireless charging pad with an effective powering area of 144 cm2 is fabricated on 3D-assembled printed circuit boards. This 3D structure obviates the need for traditional magnetic shield materials that place limitations on the working frequency and suffer from non-linearity and hysteresis effects.

A Review of Methods and Challenges for Improvement in Efficiency and Distance for Wireless Power Transfer Applications

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Sokol Kuka ◽  
Kai Ni ◽  
Mohammed Alkahtani
Keyword(s):  
Electric Vehicles ◽  
Power Efficiency ◽  
Near Field ◽  
Electronic Devices ◽  
Wireless Power Transfer ◽  
Power Transfer ◽  
Wireless Power ◽  
Inductive Power Transfer ◽  
The Past ◽  
Transmission Distance

AbstractOver the past few years, interest and research in wireless power transfer (WPT) have been rapidly incrementing, and as an effect, this is a remarkable technology in many electronic devices, electric vehicles and medical devices. However, most of the applications have been limited to very close distances because of efficiency concerns. Even though the inductive power transfer technique is becoming relatively mature, it has not shown near-field results more than a few metres away transmission. This review is focused on two fundamental aspects: the power efficiency and the transmission distance in WPT systems. Introducing the principles and the boundaries, scientific articles will be reviewed and discussed in terms of their methods and respective challenges. This paper also shows more important results in efficiency and distance obtained, clearly explaining the theory behind and obstacles to overcome. Furthermore, an overlook in other aspects and the latest research studies for this technology will be given. Moreover, new issues have been raised including safety and security.

scholarly journals Single-Tube and Multi-Turn Coil Near-Field Wireless Power Transfer for Low-Power Home Appliances

Energies ◽  
2018 ◽  
Vol 11 (8) ◽  
pp. 1969 ◽  
Author(s):  
Aqeel Jawad ◽  
Rosdiadee Nordin ◽  
Sadik Gharghan ◽  
Haider Jawad ◽  
Mahamod Ismail ◽  
...  
Keyword(s):  
Low Power ◽  
Power Efficiency ◽  
Copper Wire ◽  
Near Field ◽  
Wireless Power Transfer ◽  
Battery Life ◽  
Total System ◽  
Power Transfer ◽  
Wireless Power ◽  
Single Tube

Single-tube loop coil (STLC) and multi-turn copper wire coil (MTCWC) wireless power transfer (WPT) methods are proposed in this study to overcome the challenges of battery life during low-power home appliance operations. Transfer power, efficiency, and distance are investigated for charging mobile devices on the basis of the two proposed systems. The transfer distances of 1–15 cm are considered because the practicality of this range has been proven to be reliable in the current work on mobile device battery charging. For STLC, the Li-ion battery is charged with total system efficiencies of 86.45%, 77.08%, and 52.08%, without a load, at distances of 2, 6, and 15 cm, respectively. When the system is loaded with 100 Ω at the corresponding distances, the transfer efficiencies are reduced to 80.66%, 66.66%, and 47.04%. For MTCWC, the battery is charged with total system efficiencies of 88.54%, 75%, and 52.08%, without a load, at the same distances of 2, 6, and 15 cm. When the system is loaded with 100 Ω at the corresponding distances, the transfer efficiencies are drastically reduced to 39.52%, 33.6%, and 15.13%. The contrasting results, between the STLC and MTCWC methods, are produced because of the misalignment between their transmitters and receiver coils. In addition, the diameter of the MTCWC is smaller than that of the STLC. The output power of the proposed system can charge the latest smartphone in the market, with generated output powers of 5 W (STLC) and 2 W (MTCWC). The above WPT methods are compared with other WPT methods in the literature.

scholarly journals Near-Field Wireless Power and Data Transmission Through two-wire Power Carrier

2020 ◽  
Vol 9 (9) ◽  
pp. 463-467
Keyword(s):  
Magnetic Induction ◽  
Power Efficiency ◽  
Information Transfer ◽  
Near Field ◽  
Mode Switching ◽  
Receiver Design ◽  
Power Transfer ◽  
Wireless Power ◽  
Induction Principle ◽  
Power Transfer Efficiency

These days wireless power transfer is the widely used technology to transmit power and information simultaneously. In this paper, the magnetic induction principle is used to transfer power and information simultaneously through a single winding arrangement. It is shown that a 7W LED lamp can be illuminated between a distance of about 5mm. Magnetic induction principle can be applied to a short-range power and information transfer only. This paper discusses the underwater LED light luminaire transmitter and receiver design components, along with it shows the mode switching of LED. The power transfer efficiency is about 65% when the transmitter and receiver are placed in-line and power efficiency decreases with the displacement of the lamp to either side.

scholarly journals A low-power prototype of contactless field power controlled BLAC and BLDC motors

2020 ◽  
Vol 7 (2) ◽  
pp. 106-115
Author(s):  
Umesh Kumar Soni ◽  
Ramesh Kumar Tripathi
Keyword(s):  
High Frequency ◽  
Permanent Magnets ◽  
Single Layer ◽  
Secondary Coil ◽  
Power Transfer ◽  
Hollow Shaft ◽  
Position Detection ◽  
Dc Power ◽  
Ac Power ◽  
Carbon Brushes

AbstractIn this paper, a new design configuration has been proposed in which a prototype of resonant inductive power transfer-based contactless power transfer to wound rotor has been developed which provides field power to brushless alternating current (BLAC) or brushless direct current (BLDC) motors without the use of permanent magnets in the rotor. Further, wound field in the rotor of DC motor can be powered without carbon brushes. The proposed design facilitates motor performance improvement by adding an extra dimension of field flux control, while the armature circuit is conventionally fed from position detection and commutation schemes. It contains a primary multilayer concentrated coil fed with high-frequency resonating AC supply or switched mode supply. A single layer helical secondary coil coaxially fixed on the shaft receives high frequency wireless AC power transmitted from primary coil. Fast rectifier inside the hollow shaft and DC filter provides the transferred DC power to field terminals in the rotor. It has been verified that rotor power can be varied linearly with linear variation in input DC power with the highest efficiency at the resonant frequency. Available power to the rotor remains invariable with rotational speed and angle, which is a necessary requirement for rotor field. DC voltage on the rotor terminals can be effectively controlled during standstill as well as during rotation at any speed.

TRIPLEPR-MAC: A Triple Queue Priority Based Medium Access Control Protocol for Wireless Sensor Network

2019 ◽  
Vol 09 ◽  
Author(s):  
Rinkuben N. Patel ◽  
Nirav V. Bhatt
Keyword(s):  
Sensor Network ◽  
Data Transmission ◽  
Energy Efficient ◽  
Power Efficiency ◽  
Mac Protocol ◽  
Medium Access Control Protocol ◽  
Quality Factors ◽  
Medium Access ◽  
Critical Fields ◽  
Storage Unit

Background: WSN is a network of smart tiny electromechanical devices named as sensors. Sensors perform various tasks like sensing the environment as per its range, transmit the data using transmission units, store the data in the storage unit and perform an action based on captured data. As they are installed in an unfriendly environment, to recharge the sensors are not possible every time which leads to a limited lifetime of a network. To enhance the life of a sensor network, the network required energy-efficient protocols. Various energy-efficient MAC protocols are developed by Research community, but very few of them are integrated with the priority-based environment which performs the priority-based data transmission. Another challenge of WSN is, most of the WSN areas are delay-sensitive because it is implemented in critical fields like military, disaster management, and health monitoring. Energy, Delay, and throughput are major quality factors that affect the sensor network. Objective: In this paper, the aim is to design and develop a MAC Protocol for a field like the military where the system requires energy efficiency and priority-based data transmission. Method: In the proposed model, the cluster-based network with priority queues are formed that can achieve higher power efficiency and less delay for sensitive data. Results: In this research simulation of Proposed MAC, TMAC and SMAC are done with different numbers of nodes, same inter-packet intervals, and variant inter-packet intervals. Based on the script simulation, result graphs are generated. Conclusion: The proposed work achieves greater lifetime compared to TMAC and SMAC using priority-based data transmission.

Sign in / Sign up

Export Citation Format

Share Document