scholarly journals Measurements and Simulation Study of Daylight Availability and Its Impact on the Heating, Cooling and Lighting Energy Demand in an Educational Building

Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2555
Author(s):  
Joanna Rucińska ◽  
Adrian Trząski
Keyword(s):  
Energy Balance ◽  
Energy Demand ◽  
Energy Performance ◽  
Primary Energy ◽  
Calculation Model ◽  
Simulation Software ◽  
Zero Energy Building ◽  
Lighting Energy ◽  
Lighting Systems ◽  
The Impact

This paper deals with the impact of the use of daylight on the overall energy demand for heating, cooling, and lighting in educational buildings. The energy performance of buildings is currently of the utmost importance as current European regulations, starting from 31st December 2020 impose that all new buildings must meet nearly zero-energy building requirements. This paper presents a study of the illuminance distribution in an educational room obtained from measurements and simulation results using two different models. One of the models, integrated with a thermal simulation software, was used to estimate the impact of daylight on the energy demand. The analysis included the use of various window types, lighting control system, reference point location, and daylight calculation model for a sample room in an educational building. Results of the analysis indicate that, due to the high share of lighting demand (reaching up to 78% of the primary energy balance), there is a need to take into account the efficiency of lighting systems during the design process to correctly determine the actual energy balance of a building, increase the quality of the design of lighting systems, as well as to select the optimal parameters of windows.

Architectural Elements with Respect to the Energy Performance of Buildings

2014 ◽  
Vol 1020 ◽  
pp. 561-565 ◽  
Author(s):  
Rastislav Ingeli ◽  
Katarína Minarovičová ◽  
Miroslav Čekon
Keyword(s):  
Energy Demand ◽  
Energy Use ◽  
Energy Performance ◽  
High Energy ◽  
Primary Energy ◽  
Zero Energy ◽  
Architectural Elements ◽  
Zero Energy Building ◽  
Very High Energy ◽  
Building Operation

Buildings account for 40% of the primary energy use and 24%of the generation of green house gases worldwide. Therefore, a reduction of the specific energy demand of buildings and increased use of renewable energy are important measures of climate change mitigation. On the 18th of May 2010 a recast of the EPBD was approved which further clarifies the intention that buildings shall have a low energy demand. The recast of the EPBD specifies that by the end of 2020 all new buildings shall be “nearly zero-energy buildings”. A nearly zero-energy building is defined as a building with a very high energy performance and very simple shape. The current focusing on the energy efficiency of the building operation may lead to uniform cuboid architecture with heavy insulated building envelopes. The paper deals with the influence of energy concept on architectural elements (and their properties as shape, material, colour, texture etc.)

scholarly journals Improving the Passive Energy Performance of the Buildings’ Envelope in the Southern European Area: A Study on the Integration of a Tensile Material

2021 ◽  
Vol 65 (2-4) ◽  
pp. 345-352
Author(s):  
Giovanni Ciampi ◽  
Yorgos Spanodimitriou ◽  
Niloufar Mokhtari ◽  
Michelangelo Scorpio ◽  
Antonio Rosato ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Energy Demand ◽  
Energy Performance ◽  
Polyester Fabric ◽  
Primary Energy ◽  
Simulation Software ◽  
Office Building ◽  
European Area ◽  
Carbon Dioxide Equivalent ◽  
East West

In this paper, the energy and environmental impacts of a passive retrofit action, involving the installation, on an office building, of a second-skin system with the external layer made of a PVC-coated polyester fabric, were evaluated in terms of primary energy saving and carbon dioxide equivalent emissions. The primary energy consumption and the carbon dioxide equivalent emissions associated with the considered case studies were evaluated through the dynamic simulation software TRNSYS, across a whole year. The study was carried out considering five cities (Athens, Barcelona, Lisbon, Marseille and Naples) in five different countries in southern Europe upon varying the orientation of the two main façades of building (north-south and east-west orientation were considered). The office building was modeled in detail considering different construction characteristics upon varying the country. The simulation results highlight that the best results in terms of PES (equal to 22.4%) in Naples, while the best results in terms of CO2 (equal to 32.0 MgCO2,eq) were obtained when the building is located in Athens. In addition, the adoption of the proposed passive lightweight retrofit solution allowed the reduction of both cooling and thermal yearly energy demand up to 57.7% (Marseille) and 17.8% (Barcelona), respectively.

scholarly journals THE INFLUENCE OF SCHEDULES OF OPEN OFFICE OCCUPANTS’ PRESENCE ON BUILDING’S ENERGY DEMAND

2020 ◽  
Author(s):  
Jonas Bielskus ◽  
Violeta Motuzienė
Keyword(s):  
Energy Efficient ◽  
Energy Demand ◽  
Energy Performance ◽  
Primary Energy ◽  
Simulation Software ◽  
Design Stage ◽  
Sustainable Buildings ◽  
Standard Case ◽  
Primary Energy Demand ◽  
Performance Calculation

Many studies show, that there is a difference between actual and design energy consumption in energy efficient and sustainable buildings. As a rule, buildings consume more energy than it has been foreseen at the design stage. Occupants’ behaviour in buildings is also identified as one of the main reasons causing the so called Performance Gap. Having mobile workstations, opened plan offices are becoming more popular in design solutions in sustainable buildings. Here we have studied one of such office spaces. Monitoring of real occupancy was performed and real occupation schedules were statistically generated. The schedules were compared to the ones given by European Standard for energy performance calculation as well as with default schedules proposed by simulation software DesignBuilder. The comparison shows a significantly lower measured occupancy compared to the above-mentioned schedules. To compare the influence of occupancy related assumptions on predicted energy demand, DesignBuilder model was created and simulated for 3 different occupancy schedules. The results have shown that primary energy demand of a building due to assumptions related with an occupancy, compared to default DesignBuilder schedules are: 111 kWh/m² (32%) higher than the standard case and 152 kWh/m² (44%) than the actual one.

scholarly journals Energy Flexibility as Additional Energy Source in Multi-Energy Systems with District Cooling

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 519
Author(s):  
Alice Mugnini ◽  
Gianluca Coccia ◽  
Fabio Polonara ◽  
Alessia Arteconi
Keyword(s):  
Energy Source ◽  
Energy Demand ◽  
Energy Systems ◽  
Energy System ◽  
Energy Performance ◽  
Primary Energy ◽  
Energy Sources ◽  
Variable Load ◽  
Additional Energy ◽  
The Impact

The integration of multi-energy systems to meet the energy demand of buildings represents one of the most promising solutions for improving the energy performance of the sector. The energy flexibility provided by the building is paramount to allowing optimal management of the different available resources. The objective of this work is to highlight the effectiveness of exploiting building energy flexibility provided by thermostatically controlled loads (TCLs) in order to manage multi-energy systems (MES) through model predictive control (MPC), such that energy flexibility can be regarded as an additional energy source in MESs. Considering the growing demand for space cooling, a case study in which the MPC is used to satisfy the cooling demand of a reference building is tested. The multi-energy sources include electricity from the power grid and photovoltaic modules (both of which are used to feed a variable-load heat pump), and a district cooling network. To evaluate the varying contributions of energy flexibility in resource management, different objective functions—namely, the minimization of the withdrawal of energy from the grid, of the total energy cost and of the total primary energy consumption—are tested in the MPC. The results highlight that using energy flexibility as an additional energy source makes it possible to achieve improvements in the energy performance of an MES building based on the objective function implemented, i.e., a reduction of 53% for the use of electricity taken from the grid, a 43% cost reduction, and a 17% primary energy reduction. This paper also reflects on the impact that the individual optimization of a building with a multi-energy system could have on other users sharing the same energy sources.

scholarly journals Energy Performance Assessment of Innovative Building Solutions Coming from Construction and Demolition Waste Materials

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1226
Author(s):  
Beatriz Fraga-De Cal ◽  
Antonio Garrido-Marijuan ◽  
Olaia Eguiarte ◽  
Beñat Arregi ◽  
Ander Romero-Amorrortu ◽  
...  
Keyword(s):  
Thermal Insulation ◽  
Energy Demand ◽  
Energy Savings ◽  
Flow Analysis ◽  
Weather Conditions ◽  
Energy Performance ◽  
Construction And Demolition Waste ◽  
The European Union ◽  
Demolition Waste ◽  
The Impact

Prefabricated solutions incorporating thermal insulation are increasingly adopted as an energy conservation measure for building renovation. The InnoWEE European project developed three technologies from Construction and Demolition Waste (CDW) materials through a manufacturing process that supports the circular economy strategy of the European Union. Two of them consisted of geopolymer panels incorporated into an External Thermal Insulation Composite System (ETICS) and a ventilated façade. This study evaluates their thermal performance by means of monitoring data from three pilot case studies in Greece, Italy, and Romania, and calibrated building simulation models enabling the reliable prediction of energy savings in different climates and use scenarios. Results showed a reduction in energy demand for all demo buildings, with annual energy savings up to 25% after placing the novel insulation solutions. However, savings are highly dependent on weather conditions since the panels affect cooling and heating loads differently. Finally, a parametric assessment is performed to assess the impact of insulation thickness through an energy performance prediction and a cash flow analysis.

scholarly journals Renovation of Public Lighting Systems in Cultural Landscapes: Lighting and Energy Performance and Their Impact on Nightscapes

Energies ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 509
Author(s):  
Lodovica Valetti ◽  
Francesca Floris ◽  
Anna Pellegrino
Keyword(s):  
Energy Efficient ◽  
Flux Distribution ◽  
Cultural Landscapes ◽  
Energy Performance ◽  
Luminous Flux ◽  
Landscape Value ◽  
Reduce Energy Consumption ◽  
Lighting Systems ◽  
The Impact ◽  
Positive Effect

The technological innovation in the field of lighting and the need to reduce energy consumption connected to public lighting are leading many municipalities to undertake the renewal of public lighting systems, by replacing the existing luminaires with LED technologies. This renovation process is usually aimed at increasing energy efficiency and reducing maintenance costs, whist improving the lighting performance. To achieve these results, the new luminaires are often characterised by a luminous flux distribution much more downward oriented, which may remarkably influence and alter the perception of the night image of the sites. In this study the implications of the renovation of public lighting systems in terms of lighting and energy performance as well as the effects relating to the alteration of the night image, in historical contexts characterized by significant landscape value, are analysed. Results, along with demonstrating the positive effect that more sustainable and energy efficient lighting systems may have on the lighting performance and energy consumptions of public lighting systems, evidences the impact they may have on the alteration of the nocturnal image.

Analysis of Energy Sources on Energy Indicators Performance

2016 ◽  
Vol 861 ◽  
pp. 198-205
Author(s):  
Anton Pitonak ◽  
Martin Lopusniak
Keyword(s):  
European Union ◽  
Energy Demand ◽  
Energy Performance ◽  
Primary Energy ◽  
Hot Water ◽  
Energy Class ◽  
The European Union ◽  
Total Consumption ◽  
Minimum Requirements ◽  
Global Indicator

In the members states of the European Union, portion of buildings in the total consumption of energy represents 40%, and their portion in CO2 emissions fluctuates around 35%. The European Union is trying to protect the environment by reducing energy demand and releasing CO2 emissions into the air. Energy performance is the quantity of energy, which is necessary for heating and domestic hot water production, for cooling and ventilation and for lighting. Based on results of energy performance, individual buildings are classified into energy classes A to G. A global indicator (primary energy) is the decisive factor for final evaluation of the building. The new building must meet minimum requirements for energy performance, i.e. it must be classified to energy class A1 since 2016, and to energy class A0 since 2020. The paper analyses effect of the use of different resources of heat in a family house designed according to requirements valid since 2020, and its subsequent classification into an energy class.

Developing vietnam's oil and gas industry in association with energy and economic security in the international integration period

2021 ◽  
Vol 11 ◽  
pp. 55-61
Author(s):  
Thuong San Ngo
Keyword(s):  
Energy Balance ◽  
Energy Demand ◽  
Oil And Gas ◽  
Renewable Resource ◽  
Oil And Gas Industry ◽  
Primary Energy ◽  
Economic Security ◽  
Total Production ◽  
State Budget ◽  
Gas Industry

Oil and gas is a non-renewable resource that plays an important role in the economy. It is forecasted that by the middle of the twenty-first century, oil and gas still holds the leading position in primary energy balance in many countries. The world energy consumption in 2020 was over 4.1 billion tons of oil and 3,853 billion m3 of gas [1]. During 60 years of construction and development, Vietnam's oil and gas industry has made important contributions to the economy, especially helping the country overcome the energy crisis and budget deficit in the 1990s. By the end of 2020, the total production amounted to over 424 million tons of oil and condensate, and over 160 billion m3 of gas; at one time even contributing nearly 30% of the State budget and 22 - 25% of the GDP. Especially, the formation of important coastal petroleum industrial zones and oil and gas projects on the continental shelf have contributed to ensuring national sovereignty and national security. The demand for oil and gas in the energy balance increases rapidly with the speed of socio-economic development. It is forecasted that in the near future, Vietnam will no longer be self-sufficient in supply and must import completely to meet the country's energy demand. In parallel with proactively implementing urgent technical and technological solutions, Vietnam's oil and gas industry needs mechanisms to increase reserves and maintain oil and gas output, as well as prepare the next steps for transition to energy forms with low greenhouse gas emissions and renewable energy.

Sustainable energy solutions for thermal load in buildings - Role of heat pumps, solar thermal, and hydrogen-based cogeneration systems

2021 ◽  
pp. 1-25
Author(s):  
Praveen Cheekatamarla ◽  
Vishaldeep Sharma ◽  
Bo Shen
Keyword(s):  
Energy Efficiency ◽  
Renewable Energy ◽  
Carbon Footprint ◽  
Energy Demand ◽  
Primary Energy ◽  
Heat Pumps ◽  
Total Carbon ◽  
Coefficient Of Performance ◽  
Renewable Energy Resources ◽  
The Impact

Abstract Economic and population growth is leading to increased energy demand across all sectors – buildings, transportation, and industry. Adoption of new energy consumers such as electric vehicles could further increase this growth. Sensible utilization of clean renewable energy resources is necessary to sustain this growth. Thermal needs in a building pose a significant challenge to the energy infrastructure. Supporting the current and future building thermal energy needs to offset the total electric demand while lowering the carbon footprint and enhancing the grid flexibility is presented in this study. Performance assessment of heat pumps, renewable energy, non-fossil fuel-based cogeneration systems, and their hybrid configurations was conducted. The impact of design configuration, coefficient of performance (COP), electric grid's primary energy efficiency on the key attributes of total carbon footprint, life cycle costs, operational energy savings, and site-specific primary energy efficiency are analyzed and discussed in detail.

scholarly journals Impacts of Microclimate Conditions on the Energy Performance of Buildings in Urban Areas

Buildings ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 189 ◽  
Author(s):  
Javanroodi ◽  
M.Nik
Keyword(s):  
Urban Areas ◽  
Energy Demand ◽  
Weather Conditions ◽  
Energy Performance ◽  
Urban Morphology ◽  
Weather Data ◽  
Architectural Form ◽  
Energy Performance Of Buildings ◽  
Microclimate Conditions ◽  
The Impact

Urbanization trends have changed the morphology of cities in the past decades. Complex urban areas with wide variations in built density, layout typology, and architectural form have resulted in more complicated microclimate conditions. Microclimate conditions affect the energy performance of buildings and bioclimatic design strategies as well as a high number of engineering applications. However, commercial energy simulation engines that utilize widely-available mesoscale weather data tend to underestimate these impacts. These weather files, which represent typical weather conditions at a location, are mostly based on long-term metrological observations and fail to consider extreme conditions in their calculation. This paper aims to evaluate the impacts of hourly microclimate data in typical and extreme climate conditions on the energy performance of an office building in two different urban areas. Results showed that the urban morphology can reduce the wind speed by 27% and amplify air temperature by more than 14%. Using microclimate data, the calculated outside surface temperature, operating temperature and total energy demand of buildings were notably different to those obtained using typical regional climate model (RCM)–climate data or available weather files (Typical Meteorological Year or TMY), i.e., by 61%, 7%, and 21%, respectively. The difference in the hourly peak demand during extreme weather conditions was around 13%. The impact of urban density and the final height of buildings on the results are discussed at the end of the paper.

Sign in / Sign up

Export Citation Format

Share Document