scholarly journals Practical Performance Analysis of a Bifacial PV Module and System

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4389
Author(s):  
Juhee Jang ◽  
Kyungsoo Lee
Keyword(s):  
Short Circuit ◽  
Rear Surface ◽  
Short Circuit Current ◽  
Specific Yield ◽  
Rear Side ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Pm 10 ◽  
Sky Conditions

Bifacial photovoltaic (PV) modules can take advantage of rear-surface irradiance, enabling them to produce more energy compared with monofacial PV modules. However, the performance of bifacial PV modules depends on the irradiance at the rear side, which is strongly affected by the installation setup and environmental conditions. In this study, we experiment with a bifacial PV module and a bifacial PV system by varying the size of the reflective material, vertical installation, temperature mismatch, and concentration of particulate matter (PM), using three testbeds. From our analyses, we found that the specific yield increased by 1.6% when the reflective material size doubled. When the PV module was installed vertically, the reduction of power due to the shadow effect occurred, and thus the maximum current was 14.3% lower than the short-circuit current. We also observed a maximum average surface temperature mismatch of 2.19 °C depending on the position of the modules when they were composed in a row. Finally, in clear sky conditions, when the concentration of PM 10 changed by 100 µg/m3, the bifacial gain increased by 4%. In overcast conditions, when the concentration of PM 10 changed by 100 µg/m3, the bifacial gain decreased by 0.9%.

scholarly journals Measurement and validation of polysilicon photovoltaic module degradation rates over five years of field exposure in Oman

AIMS Energy ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1192-1212
Author(s):  
Honnurvali Mohamed Shaik ◽  
◽  
Adnan Kabbani ◽  
Abdul Manan Sheikh ◽  
Keng Goh ◽  
...  
Keyword(s):  
Loss Factor ◽  
Visual Loss ◽  
Short Circuit ◽  
Production Capacity ◽  
Short Circuit Current ◽  
Photovoltaic Module ◽  
Pv System ◽  
Field Exposure ◽  
Degradation Rates ◽  
Pv Modules

<abstract> <p>Degradation of PV modules have a severe impact on its power-producing capabilities thus affecting the reliability, performance over the long run. To understand the PV degradation happening under the influence of local environmental conditions a survey was conducted on six polycrystalline silicon-based PV modules over five years. It has been observed that the average degradation rates stood at 1.02%/year at irradiances 800 W/m<sup>2</sup> and 0.99%/year at irradiances 600 W/m<sup>2</sup>, which are almost double the manufacturer proposed values. Upon further investigations, it has been found that discoloration of encapsulant in modules 3, 5, and 6 have been the main factor causing the reduction of the short circuit current (I<sub>sc</sub>) thus affecting the overall power production capacity of the installed PV system. Considering the amount of time, resources and manpower invested to perform this survey an alternate way of estimating the PV degradation rates is also investigated. The exponential decay factor-based model is adopted to correlate the encapsulant discoloration seen on-site in the form of a mathematical equation to predict the current loss. This loss is defined as the visual loss factor in this paper. Further, the output I-V curves are simulated using MATLAB Simulink-based mathematical model which also integrates visual loss factor (VLF) losses into it. Such simulated I-V curves have shown a good match with the measured I-V curves at the same irradiance with an error less than 3%. Authors anticipate that this modelling approach can open the door for further research in developing algorithms that can simulate the PV degradation rates.</p> </abstract>

Insight into Al–Si interface of PERC by Kelvin probe force microscopy

2019 ◽  
Vol 12 (05) ◽  
pp. 1950078
Author(s):  
Xingbo Wang ◽  
Guoyu Qian ◽  
Zhou Gao ◽  
Xing Jiang ◽  
Yongji Chen ◽  
...  
Keyword(s):  
Surface Potential ◽  
Crystalline Silicon ◽  
Short Circuit ◽  
Rear Surface ◽  
Short Circuit Current ◽  
Kelvin Probe Force Microscopy ◽  
Rear Side ◽  
Kelvin Probe ◽  
Potential Step ◽  
Force Microscopy

Passivated emitter and rear cell (PERC) has the advantage of higher short circuit current and open circuit voltage, which are generally claimed to be related to the reduction of rear side recombination and the increase of rear surface reflection. However, few works have focused on exploring the internal conducting mechanism about it. Herein, the influence of PERC technique on improving the short circuit current is investigated by comparing a PERC with a single crystalline silicon (sc-Si) solar cell. The surface potential results measured by Kelvin probe force microscopy show a higher surface potential step at the Al–Si interface of PERC than that of sc-Si cell, indicating a severe energy band variation and a better carrier collecting ability of PERC. Moreover, by using advanced microstructure characterization techniques, the relationship among the surface potential step, morphology and element distribution is fully studied, which proposes a new viewpoint to explain the enhanced performance of PERC.

scholarly journals Estimation of Photovoltaic Module Parameters based on Total Error Minimization of I-V Characteristic

2018 ◽  
Vol 7 (3) ◽  
pp. 425-432
Author(s):  
M. N. Abdullah ◽  
M. Z. Hussin ◽  
S. A. Jumaat ◽  
N. H. Radzi ◽  
Lilik J. Awalin
Keyword(s):  
Short Circuit ◽  
Total Error ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Parameters Estimation ◽  
Maximum Power ◽  
Photovoltaic Module ◽  
Estimation Model ◽  
Pv System ◽  
Pv Modules

Mathematical Modelling of photovoltaic (PV) modules is important for simulation and performance analysis of PV system. Therefore, an accurate parameters estimation is necessary. Single-diode and two-diode model are widely used to model the PV system. However, it required to determine several parameters such as series and shunt resistances that not provided in datasheet.  The main goal of PV modelling technique is to obtain the accurate parameters to ensure the I-V characteristic is closed to the manufacturer datasheet. Previously, the maximum power error of calculated and datasheet value are considered as objective to be minimized for both models. This paper proposes the PV parameter estimation model based minimizing the total error of open circuit voltage (VOC), short circuit current (ISC) and maximum power (PMAX) where all these parameters are provided by the manufacturer. The performance of single-diode and two-diode models are tested on different type of PV modules using MATLAB. It found that the two-diode model obtained accurate parameters with smaller error compared to single-diode model. However, the simulation time is slightly higher than single-diode model due extra calculation required.

scholarly journals The Reliability Analysis of PV Panels Installed in KP Region

2020 ◽  
Vol 7 (10) ◽  
pp. 384-389
Author(s):  
Jawad Ahmad ◽  
Keyword(s):  
Short Circuit ◽  
Equivalent Circuit Model ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic System ◽  
Photovoltaic Module ◽  
Pv System ◽  
Peak Voltage ◽  
Pv Module ◽  
Term Performance

Reliability and long term performance of photovoltaic (PV) system is of vital importance in switching from conventional sources to sustainable one. Design, study and analysis of key components in a photovoltaic power system starting from generation of power to withstands number of climatic stresses and uninterrupted power supply plays a key role. One of the key elements in photovoltaic system is photovoltaic module. Also power generated in photovoltaic system is dependent on a source of energy that changes in every instant and with the passage of time during its operation .Hence it is paramount to build a long lasting photovoltaic module and analyze characteristics of the PV module under various conditions. This paper presents an efficient PV module based on PV equivalent circuit model using MATLAB/Simulink, and compared the simulated model results with manufacturer’s specifications like peak current, peak voltage, open circuit voltage and short circuit current .Also the performance of the module under variation of series resistance, irradiation, and temperature are analyzed. Data from five different areas across KP are noted and the results were Simulated and compared with the rated data.

scholarly journals Prediction of Solar Irradiance Based on Artificial Neural Networks

Inventions ◽  
2019 ◽  
Vol 4 (3) ◽  
pp. 45 ◽  
Author(s):  
Waleed I. Hameed ◽  
Baha A. Sawadi ◽  
Safa J. Al-Kamil ◽  
Mohammed S. Al-Radhi ◽  
Yasir I. A. Al-Yasir ◽  
...  
Keyword(s):  
Neural Networks ◽  
Artificial Neural Networks ◽  
Solar Irradiance ◽  
Open Circuit Voltage ◽  
Low Cost ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Pv Module ◽  
Artificial Neural

Prediction of solar irradiance plays an essential role in many energy systems. The objective of this paper is to present a low-cost solar irradiance meter based on artificial neural networks (ANN). A photovoltaic (PV) mathematical model of 50 watts and 36 cells was used to extract the short-circuit current and the open-circuit voltage of the PV module. The obtained data was used to train the ANN to predict solar irradiance for horizontal surfaces. The strategy was to measure the open-circuit voltage and the short-circuit current of the PV module and then feed it to the ANN as inputs to get the irradiance. The experimental and simulation results showed that the proposed method could be utilized to achieve the value of solar irradiance with acceptable approximation. As a result, this method presents a low-cost instrument that can be used instead of an expensive pyranometer.

Effect of Unglazed Transpired Collector on the Performance of a Polycrystalline Silicon Photovoltaic Module

2006 ◽  
Vol 128 (3) ◽  
pp. 349-353 ◽  
Author(s):  
A. T. Naveed ◽  
E. C. Kang ◽  
E. J. Lee
Keyword(s):  
Polycrystalline Silicon ◽  
Electrical Power ◽  
Heating System ◽  
Photovoltaic Module ◽  
Forced Ventilation ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Typical Day ◽  
Electrical Output

The electrical power generated by a polycrystalline silicon photovoltaic (PV) module mounted on an unglazed transpired solar collector (UTC) has been studied and compared to that of a PV module without UTC for a quantitative analysis of electrical output and its role in reducing the simple payback periods of photovoltaic electrical systems. A 75W polycrystalline silicon PV module was fixed on an UTC in front of the ventilation fan, and effectiveness of cooling by means of the forced ventilation at the rate of 160CFM was monitored. The temperature reduction under forced ventilation was in the range of 3-9°C with a 5% recovery in the electrical output power on a typical day of the month of February 2005. The simulated and measured electrical power outputs are in reasonable agreement with root-mean-square error of 2.40. The life cycle assessment of a hypothetical PV system located at Daejeon, South Korea and consisting of 3kW PV modules fixed on a 50m2 UTC shows that with a possible reduction of 3-9°C in the operating temperatures, the system requires three 75W fewer PV modules. The simple payback period of PV system is reduced from 23yearsto15years when integrated into an UTC air heating system.

scholarly journals Feasibility Study of the Technical and Economic Performance of Grid-Connected PV System for Selected Rooftops in UTHM

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Mohamad Fakrie Mohamad Ali ◽  
◽  
Mohd Noor Abdullah ◽  
Keyword(s):  
Feasibility Study ◽  
Crystalline Silicon ◽  
Electricity Consumption ◽  
Payback Period ◽  
Net Energy ◽  
Pv System ◽  
Pv Module ◽  
Electricity Bill ◽  
Pv Modules ◽  
Energy Metering

This paper presents the feasibility study of the technical and economic performances of grid-connected photovoltaic (PV) system for selected rooftops in Universiti Tun Hussein Onn Malaysia (UTHM). The analysis of the electricity consumption and electricity bill data of UTHM campus show that the monthly electricity usage in UTHM campus is very high and expensive. The main purpose of this project is to reduce the annual electricity consumption and electricity bill of UTHM with Net Energy Metering (NEM) scheme. Therefore, the grid-connected PV system has been proposed at Dewan Sultan Ibrahim (DSI), Tunku Tun Aminah Library (TTAL), Fakulti Kejuruteraan Awam dan Alam Bina (FKAAS) and F2 buildings UTHM by using three types of PV modules which are mono-crystalline silicon (Mono-Si), poly-crystalline silicon (Poly-Si) and Thin-film. These three PV modules were modeled, simulated and calculated using Helioscope software with the capacity of 2,166.40kWp, 2,046.20kWp and 1,845kWp respectively for the total rooftop area of 190,302.9 ft². The economic analysis was conducted on the chosen three installed PV modules using RETScreen software. As a result, the Mono-Si showed the best PV module that can produce 2,332,327.40 kWh of PV energy, 4.4% of CO₂ reduction, 9.3 years of payback period considering 21 years of the contractual period and profit of RM4,932,274.58 for 11.7 years after payback period. Moreover, the proposed installation of 2,166.40kWp (Mono-SI PV module) can reduce the annual electricity bill and CO2 emission of 3.6% (RM421,561.93) and 4.4% (1,851.40 tCO₂) compared to the system without PV system.

The Effect of Al-BSF on Seff and Rb in Industrialized Mono-Silicon Solar Cells

2012 ◽  
Vol 472-475 ◽  
pp. 1846-1850
Author(s):  
Shan Shan Dai ◽  
Gao Jie Zhang ◽  
Xiang Dong Luo ◽  
Jing Xiao Wang ◽  
Wen Jun Chen ◽  
...  
Keyword(s):  
Solar Cells ◽  
Spectral Response ◽  
Short Circuit ◽  
Rear Surface ◽  
Surface Recombination ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Silicon Solar Cells ◽  
Back Surface

In this work, the effect of aluminum back surface field formed by screen printed various amount of Al paste on the effective rear surface recombination velocity (Seff) and the internal rear reflectance coeffeicient (Rb) of commercial mono-silicon solar cells was investigated. We demonstrated the effect of Seffand Rbon the performance of Al-BSF solar cells by simulating them with PC1D. The simulated results showed that the lower Seffcould get higher open circuit voltage (Voc), at the same time, the larger Rbcould get higher short-circuit current (Isc). Experimentally, we investigated the Seffand Rbthrough depositing Al paste with various amount (3.7, 5, 6, and 8 mg/cm2) for fabricating Al-BSF mono-silicon solar cells. Four group cells were characterized by light I-V, spectral response, hemispherical reflectance and scanning electron microscope (SEM) measurements. It was found that, a minimum Seffof 350 cm/s was gotten from the cells with Al paste of 8 mg/cm2, which was extracted by matching quantum efficiency (QE) from 800 nm to 1200 nm with PC1D, and a maximum Rbof 53.5% was obtained from Al paste of 5 mg/cm2by calculating at 1105 nm with PC1D. When the amount of Al paste was higher than 5mg/cm2, there were less Seffand lower Rb. On the other hand, when Al amount was 3.7mg/cm2, it was too little to form a closed BSF. Based on the SEM graphs and simulations with PC1D, a simple explaination was proposed for the experimental results.

scholarly journals Optical Properties of CaF2 Thin Film Deposited on Borosilicate Glass and Its Electrical Performance in PV Module Applications

2020 ◽  
Vol 10 (16) ◽  
pp. 5647
Author(s):  
Muhammad Aleem Zahid ◽  
Shahzada Qamar Hussain ◽  
Young Hyun Cho ◽  
Junsin Yi
Keyword(s):  
Borosilicate Glass ◽  
Calcium Fluoride ◽  
Thermal Evaporation ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Average Increase ◽  
Vacuum Thermal Evaporation ◽  
Pv Module

Calcium fluoride (CaF2) is deposited via vacuum thermal evaporation on borosilicate glass to produce an anti-reflection coating for use in solar modules. Macleod’s essential simulation is used to optimize the thickness of the CaF2 coating on the glass. Experimentally, a 120 ± 4 nm-thin CaF2 film on glass shows an average increase of ~4% in transmittance and a decrease of ~3.2% in reflectance, respectively, when compared to that of uncoated glass (Un CG), within the wavelength spectrum of approximately 350 to 1100 nm. The electrical PV performance of CaF2-coated glass (CaF2-CG) was analyzed for conventional and lightweight photovoltaic module applications. An improvement in the short-circuit current (Jsc) from 38.13 to 39.07 mA/cm2 and an increase of 2.40% in the efficiency (η) was obtained when CaF2-CG glass was used instead of Un CG in a conventional module. Furthermore, Jsc enhancement from 35.63 to 36.44 mA/cm2 and η improvement of 2.32% was observed when a very thin CaF2-CG was placed between the polymethyl methacrylate (PMMA) and solar cell in a lightweight module.

Sign in / Sign up

Export Citation Format

Share Document