scholarly journals Measurement and validation of polysilicon photovoltaic module degradation rates over five years of field exposure in Oman

AIMS Energy ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1192-1212
Author(s):  
Honnurvali Mohamed Shaik ◽  
◽  
Adnan Kabbani ◽  
Abdul Manan Sheikh ◽  
Keng Goh ◽  
...  
Keyword(s):  
Loss Factor ◽  
Visual Loss ◽  
Short Circuit ◽  
Production Capacity ◽  
Short Circuit Current ◽  
Photovoltaic Module ◽  
Pv System ◽  
Field Exposure ◽  
Degradation Rates ◽  
Pv Modules

<abstract> <p>Degradation of PV modules have a severe impact on its power-producing capabilities thus affecting the reliability, performance over the long run. To understand the PV degradation happening under the influence of local environmental conditions a survey was conducted on six polycrystalline silicon-based PV modules over five years. It has been observed that the average degradation rates stood at 1.02%/year at irradiances 800 W/m<sup>2</sup> and 0.99%/year at irradiances 600 W/m<sup>2</sup>, which are almost double the manufacturer proposed values. Upon further investigations, it has been found that discoloration of encapsulant in modules 3, 5, and 6 have been the main factor causing the reduction of the short circuit current (I<sub>sc</sub>) thus affecting the overall power production capacity of the installed PV system. Considering the amount of time, resources and manpower invested to perform this survey an alternate way of estimating the PV degradation rates is also investigated. The exponential decay factor-based model is adopted to correlate the encapsulant discoloration seen on-site in the form of a mathematical equation to predict the current loss. This loss is defined as the visual loss factor in this paper. Further, the output I-V curves are simulated using MATLAB Simulink-based mathematical model which also integrates visual loss factor (VLF) losses into it. Such simulated I-V curves have shown a good match with the measured I-V curves at the same irradiance with an error less than 3%. Authors anticipate that this modelling approach can open the door for further research in developing algorithms that can simulate the PV degradation rates.</p> </abstract>

scholarly journals Estimation of Photovoltaic Module Parameters based on Total Error Minimization of I-V Characteristic

2018 ◽  
Vol 7 (3) ◽  
pp. 425-432
Author(s):  
M. N. Abdullah ◽  
M. Z. Hussin ◽  
S. A. Jumaat ◽  
N. H. Radzi ◽  
Lilik J. Awalin
Keyword(s):  
Short Circuit ◽  
Total Error ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Parameters Estimation ◽  
Maximum Power ◽  
Photovoltaic Module ◽  
Estimation Model ◽  
Pv System ◽  
Pv Modules

Mathematical Modelling of photovoltaic (PV) modules is important for simulation and performance analysis of PV system. Therefore, an accurate parameters estimation is necessary. Single-diode and two-diode model are widely used to model the PV system. However, it required to determine several parameters such as series and shunt resistances that not provided in datasheet.  The main goal of PV modelling technique is to obtain the accurate parameters to ensure the I-V characteristic is closed to the manufacturer datasheet. Previously, the maximum power error of calculated and datasheet value are considered as objective to be minimized for both models. This paper proposes the PV parameter estimation model based minimizing the total error of open circuit voltage (VOC), short circuit current (ISC) and maximum power (PMAX) where all these parameters are provided by the manufacturer. The performance of single-diode and two-diode models are tested on different type of PV modules using MATLAB. It found that the two-diode model obtained accurate parameters with smaller error compared to single-diode model. However, the simulation time is slightly higher than single-diode model due extra calculation required.

scholarly journals Practical Performance Analysis of a Bifacial PV Module and System

Energies ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 4389
Author(s):  
Juhee Jang ◽  
Kyungsoo Lee
Keyword(s):  
Short Circuit ◽  
Rear Surface ◽  
Short Circuit Current ◽  
Specific Yield ◽  
Rear Side ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Pm 10 ◽  
Sky Conditions

Bifacial photovoltaic (PV) modules can take advantage of rear-surface irradiance, enabling them to produce more energy compared with monofacial PV modules. However, the performance of bifacial PV modules depends on the irradiance at the rear side, which is strongly affected by the installation setup and environmental conditions. In this study, we experiment with a bifacial PV module and a bifacial PV system by varying the size of the reflective material, vertical installation, temperature mismatch, and concentration of particulate matter (PM), using three testbeds. From our analyses, we found that the specific yield increased by 1.6% when the reflective material size doubled. When the PV module was installed vertically, the reduction of power due to the shadow effect occurred, and thus the maximum current was 14.3% lower than the short-circuit current. We also observed a maximum average surface temperature mismatch of 2.19 °C depending on the position of the modules when they were composed in a row. Finally, in clear sky conditions, when the concentration of PM 10 changed by 100 µg/m3, the bifacial gain increased by 4%. In overcast conditions, when the concentration of PM 10 changed by 100 µg/m3, the bifacial gain decreased by 0.9%.

scholarly journals The Reliability Analysis of PV Panels Installed in KP Region

2020 ◽  
Vol 7 (10) ◽  
pp. 384-389
Author(s):  
Jawad Ahmad ◽  
Keyword(s):  
Short Circuit ◽  
Equivalent Circuit Model ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic System ◽  
Photovoltaic Module ◽  
Pv System ◽  
Peak Voltage ◽  
Pv Module ◽  
Term Performance

Reliability and long term performance of photovoltaic (PV) system is of vital importance in switching from conventional sources to sustainable one. Design, study and analysis of key components in a photovoltaic power system starting from generation of power to withstands number of climatic stresses and uninterrupted power supply plays a key role. One of the key elements in photovoltaic system is photovoltaic module. Also power generated in photovoltaic system is dependent on a source of energy that changes in every instant and with the passage of time during its operation .Hence it is paramount to build a long lasting photovoltaic module and analyze characteristics of the PV module under various conditions. This paper presents an efficient PV module based on PV equivalent circuit model using MATLAB/Simulink, and compared the simulated model results with manufacturer’s specifications like peak current, peak voltage, open circuit voltage and short circuit current .Also the performance of the module under variation of series resistance, irradiation, and temperature are analyzed. Data from five different areas across KP are noted and the results were Simulated and compared with the rated data.

Effect of Unglazed Transpired Collector on the Performance of a Polycrystalline Silicon Photovoltaic Module

2006 ◽  
Vol 128 (3) ◽  
pp. 349-353 ◽  
Author(s):  
A. T. Naveed ◽  
E. C. Kang ◽  
E. J. Lee
Keyword(s):  
Polycrystalline Silicon ◽  
Electrical Power ◽  
Heating System ◽  
Photovoltaic Module ◽  
Forced Ventilation ◽  
Pv System ◽  
Pv Module ◽  
Pv Modules ◽  
Typical Day ◽  
Electrical Output

The electrical power generated by a polycrystalline silicon photovoltaic (PV) module mounted on an unglazed transpired solar collector (UTC) has been studied and compared to that of a PV module without UTC for a quantitative analysis of electrical output and its role in reducing the simple payback periods of photovoltaic electrical systems. A 75W polycrystalline silicon PV module was fixed on an UTC in front of the ventilation fan, and effectiveness of cooling by means of the forced ventilation at the rate of 160CFM was monitored. The temperature reduction under forced ventilation was in the range of 3-9°C with a 5% recovery in the electrical output power on a typical day of the month of February 2005. The simulated and measured electrical power outputs are in reasonable agreement with root-mean-square error of 2.40. The life cycle assessment of a hypothetical PV system located at Daejeon, South Korea and consisting of 3kW PV modules fixed on a 50m2 UTC shows that with a possible reduction of 3-9°C in the operating temperatures, the system requires three 75W fewer PV modules. The simple payback period of PV system is reduced from 23yearsto15years when integrated into an UTC air heating system.

scholarly journals Optical Properties of CaF2 Thin Film Deposited on Borosilicate Glass and Its Electrical Performance in PV Module Applications

2020 ◽  
Vol 10 (16) ◽  
pp. 5647
Author(s):  
Muhammad Aleem Zahid ◽  
Shahzada Qamar Hussain ◽  
Young Hyun Cho ◽  
Junsin Yi
Keyword(s):  
Borosilicate Glass ◽  
Calcium Fluoride ◽  
Thermal Evaporation ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Average Increase ◽  
Vacuum Thermal Evaporation ◽  
Pv Module

Calcium fluoride (CaF2) is deposited via vacuum thermal evaporation on borosilicate glass to produce an anti-reflection coating for use in solar modules. Macleod’s essential simulation is used to optimize the thickness of the CaF2 coating on the glass. Experimentally, a 120 ± 4 nm-thin CaF2 film on glass shows an average increase of ~4% in transmittance and a decrease of ~3.2% in reflectance, respectively, when compared to that of uncoated glass (Un CG), within the wavelength spectrum of approximately 350 to 1100 nm. The electrical PV performance of CaF2-coated glass (CaF2-CG) was analyzed for conventional and lightweight photovoltaic module applications. An improvement in the short-circuit current (Jsc) from 38.13 to 39.07 mA/cm2 and an increase of 2.40% in the efficiency (η) was obtained when CaF2-CG glass was used instead of Un CG in a conventional module. Furthermore, Jsc enhancement from 35.63 to 36.44 mA/cm2 and η improvement of 2.32% was observed when a very thin CaF2-CG was placed between the polymethyl methacrylate (PMMA) and solar cell in a lightweight module.

scholarly journals Real-Time Experimental Assessment of a New MPPT Algorithm Based on the Direct Detection of the Short-Circuit Current for a PV System

2021 ◽  
Vol 19 ◽  
pp. 598-603 ◽  
Author(s):  
C.B. Nzoundja Fapi ◽  
◽  
P. Wira ◽  
M. Kamta ◽  
Keyword(s):  
Fuzzy Logic Controller ◽  
Direct Detection ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Maximum Power ◽  
Solar Irradiation ◽  
Pv System ◽  
Maximum Power Point ◽  
Pv Panel ◽  
Power Point

To substantially increase the efficiency of photovoltaic (PV) systems, it is important that the Maximum Power Point Tracking (MPPT) system has an output close to 100%.This process is handled by MPPT algorithms such as Fractional Open-Circuit Voltage (FOCV), Perturb and Observe (P&O), Fractional Short-Circuit Current (FSCC), Incremental Conductance (INC), Fuzzy Logic Controller (FLC) and Neural Network (NN) controllers. The FSCC algorithm is simple to be implemented and uses only one current sensor. This method is based on the unique existence of the linear approximation between the Maximum Power Point (MPP) current and the short-circuit current in standard conditions. The speed of this MPPT optimization technic is fast, however this algorithm needs to short-circuit the PV panel each time in order to obtain the short circuit current. This process leads to energy losses and high oscillations. In order to improve the FSCC algorithm, we propose a method based on the direct detection of the shortcircuit current by simply reading the output current of the PV panel. This value allows directly calculating the short circuit current by incrementing or decrementing the solar irradiation. Experimental results show time response attenuation, little oscillations, power losses reduction and better MPPT accuracy of the enhanced algorithm compared to the conventional FSCC method.

scholarly journals Characteristic comparison of photovoltaic module and photovoltaic thermal

2018 ◽  
Vol 204 ◽  
pp. 04010 ◽  
Author(s):  
Krismadinata ◽  
Remon Lapisa ◽  
Syahril ◽  
Asnil
Keyword(s):  
Short Circuit ◽  
Electrical Power ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Module ◽  
Heat Absorption ◽  
Electrical Characteristics ◽  
Solar Module ◽  
Circulating Water ◽  
Lower Temperature

This paper discusses an attempt to compares the electrical characteristics of two solar modules of the same type and size in which one of the solar modules at the bottom is mounted a copper pipe for circulating water (as call photovoltaic thermal). The research was steered to observe water cooling effect to electrical characteristics of PV module. This system serves as a heat absorption on the bottom of the solar module. The experiment is conducted at the same time, place, and sunlight intensity conditions for both solar modules. The characteristics of short-circuit current, open circuit voltage, upper and lower temperature and the irradiation of sunlight from the two solar modules are observed. The test results show that photovoltaic thermal generate greater electrical power than solar modules not equipped with heat absorption

scholarly journals Research on the potential-induced degradation (PID) of PV modules running in two typical climate regions

Clean Energy ◽  
2019 ◽  
Vol 3 (3) ◽  
pp. 222-226
Author(s):  
Gang Sun ◽  
Xiaohe Tu ◽  
Rui Wang
Keyword(s):  
Degradation Mechanism ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Climatic Conditions ◽  
Photovoltaic Modules ◽  
Significant Potential ◽  
Significant Difference ◽  
Pv Modules ◽  
Different Types

Abstract In order to accurately select photovoltaic modules under different climatic conditions, three kinds of polycrystalline silicon photovoltaic modules were prepared for this study using different properties of packaging materials and two typical climatic zones of China were selected for installation and operation of these photovoltaic (PV) modules. The photoelectric parameters (maximum power, open-circuit voltage, short-circuit current, etc.) and electroluminescence images of these modules were analysed before and after their operation for 6 months. The study found that the performance of PV modules in different climatic regions shows different decay tendency and degradation mechanism. There was a significant difference in the degradation of the three different types of PV modules in the sub-humid-hot region (Suzhou, Jiangsu); two kinds of photovoltaic modules using relatively poorly performing package materials showed significant potential-induced degradation effects. However, the degradation trend of the three different types of PV modules in the warm-temperate region (Kenli, Shandong) was consistent and no significant potential-induced degradation effect was observed.

Sign in / Sign up

Export Citation Format

Share Document