scholarly journals Model-Based Evaluation of Air-Side Fouling in Closed-Circuit Cooling Towers

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 695
Author(s):  
Björn Nienborg ◽  
Marc Mathieu ◽  
Alexander Schwärzler ◽  
Katharina Conzelmann ◽  
Lena Schnabel
Keyword(s):  
Cooling Tower ◽  
Laboratory Data ◽  
Measurement Data ◽  
Suspended Solid ◽  
Solid Particles ◽  
Cooling Towers ◽  
Process Technology ◽  
Data Set ◽  
Industrial Dust ◽  
Tower Model

Fouling is a permanent problem in process technology and is estimated to cost 0.25% of the gross national product. Evaporative cooling systems are especially susceptible to air-side fouling: as they work with untreated outside air, they are exposed to both natural (e.g., pollen) and human-made (e.g., industrial dust) contaminants. In addition, suspended solid particles and dissolved salts in the spray water are an issue. In this study we analyzed an approach for fouling detection based on a semi-physical (grey-box) cooling tower model which we calibrated with measurement data. A test series with reliable laboratory data indicates good applicability of the model. In three datasets, the performance decreases due to fouling (scaling, which was provoked intentionally) in the range of 5–11% were clearly detected. When applied to measurement data of two cooling towers in real applications, the model also proved to be well calibratable with relatively little data (two to four operating days). For two data sets, the model yielded reasonable results when applied to long term data: a cooling tower cleaning could be retraced and nominal operation was verified during the remaining time. During the analysis of a third data set a temporary performance deviation was found, which could not be explained with the recorded data. Thus, the approach turned out to be generally applicable but requires further verification and refinement in order to increase the robustness. If successful, it can be transferred to a commercial product for need-oriented maintenance in order to reduce cooling tower operating costs and environmental impact.

Case study: Theoretical calculation model and variable condition analysis research on the water-splashing noise for natural draft wet cooling towers

2020 ◽  
Vol 68 (2) ◽  
pp. 137-145
Author(s):  
Yang Zhouo ◽  
Ming Gao ◽  
Suoying He ◽  
Yuetao Shi ◽  
Fengzhong Sun
Keyword(s):  
Theoretical Model ◽  
Sound Pressure Level ◽  
Water Droplet ◽  
Water Distribution ◽  
Sound Pressure ◽  
Cooling Tower ◽  
Distribution Patterns ◽  
Calculation Model ◽  
Pressure Level ◽  
Cooling Towers

Based on the basic theory of water droplets impact noise, the generation mechanism and calculation model of the water-splashing noise for natural draft wet cooling towers were established in this study, and then by means of the custom software, the water-splashing noise was studied under different water droplet diameters and water-spraying densities as well as partition water distribution patterns conditions. Comparedwith the water-splashing noise of the field test, the average difference of the theoretical and the measured value is 0.82 dB, which validates the accuracy of the established theoretical model. The results based on theoretical model showed that, when the water droplet diameters are smaller in cooling tower, the attenuation of total sound pressure level of the water-splashing noise is greater. From 0 m to 8 m away from the cooling tower, the sound pressure level of the watersplashing noise of 3 mm and 6 mm water droplets decreases by 8.20 dB and 4.36 dB, respectively. Additionally, when the water-spraying density becomes twice of the designed value, the sound pressure level of water-splashing noise all increases by 3.01 dB for the cooling towers of 300 MW, 600 MW and 1000 MW units. Finally, under the partition water distribution patterns, the change of the sound pressure level is small. For the R s/2 and Rs/3 partition radius (Rs is the radius of water-spraying area), when the water-spraying density ratio between the outer and inner zone increases from 1 to 3, the sound pressure level of water-splashing noise increases by 0.7 dB and 0.3 dB, respectively.

scholarly journals Localization of Scattering Objects Using Neural Networks

Sensors ◽  
2020 ◽  
Vol 21 (1) ◽  
pp. 11
Author(s):  
Domonkos Haffner ◽  
Ferenc Izsák
Keyword(s):  
Neural Networks ◽  
Plane Waves ◽  
Measurement Data ◽  
Scattered Wave ◽  
Training Data ◽  
Data Set ◽  
Main Compound ◽  
Incident Plane ◽  
The Neural Networks ◽  
Simulation Package

The localization of multiple scattering objects is performed while using scattered waves. An up-to-date approach: neural networks are used to estimate the corresponding locations. In the scattering phenomenon under investigation, we assume known incident plane waves, fully reflecting balls with known diameters and measurement data of the scattered wave on one fixed segment. The training data are constructed while using the simulation package μ-diff in Matlab. The structure of the neural networks, which are widely used for similar purposes, is further developed. A complex locally connected layer is the main compound of the proposed setup. With this and an appropriate preprocessing of the training data set, the number of parameters can be kept at a relatively low level. As a result, using a relatively large training data set, the unknown locations of the objects can be estimated effectively.

scholarly journals Cooling tower plume abatement and plume modeling: a review

2021 ◽  
Author(s):  
Shuo Li ◽  
M. R. Flynn
Keyword(s):  
Public Health ◽  
Solar Energy ◽  
Cooling Tower ◽  
Plume Rise ◽  
Cooling Towers ◽  
Moist Air ◽  
Novel Technologies ◽  
Plume Modeling ◽  
Dry Cooling Tower ◽  
Dry Cooling

AbstractVisible plumes above wet cooling towers are of great concern due to the associated aesthetic and environmental impacts. The parallel path wet/dry cooling tower is one of the most commonly used approaches for plume abatement, however, the associated capital cost is usually high due to the addition of the dry coils. Recently, passive technologies, which make use of free solar energy or the latent heat of the hot, moist air rising through the cooling tower fill, have been proposed to minimize or abate the visible plume and/or conserve water. In this review, we contrast established versus novel technologies and give a perspective on the relative merits and demerits of each. Of course, no assessment of the severity of a visible plume can be made without first understanding its atmospheric trajectory. To this end, numerous attempts, being either theoretical or numerical or experimental, have been proposed to predict plume behavior in atmospheres that are either uniform versus density-stratified or still versus windy (whether highly-turbulent or not). Problems of particular interests are plume rise/deflection, condensation and drift deposition, the latter consideration being a concern of public health due to the possible transport and spread of Legionella bacteria.

Harmonic Analysis on Low Quality Tidal Data

2014 ◽  
Author(s):  
Joost den Haan
Keyword(s):  
Harmonic Analysis ◽  
Three Dimensional ◽  
Measurement Data ◽  
Tidal Energy ◽  
Energy Yield ◽  
Profile Measurement ◽  
Current Profile ◽  
Tidal Power ◽  
Data Set ◽  
Tidal Forcing

The aim of the study is to devise a method to conservatively predict a tidal power generation based on relatively short current profile measurement data sets. Harmonic analysis on a low quality tidal current profile measurement data set only allowed for the reliable estimation of a limited number of constituents leading to a poor prediction of tidal energy yield. Two novel, but very different approaches were taken: firstly a quasi response function is formulated which combines the currents profiles into a single current. Secondly, a three dimensional vectorial tidal forcing model was developed aiming to support the harmonic analysis with upfront knowledge of the actual constituents. The response based approach allowed for a reasonable prediction. The vectorial tidal forcing model proved to be a viable start for a full featuring numerical model; even in its initial simplified form it could provide more insight than the conventional tidal potential models.

Predicting cooling tower plume dispersion

1997 ◽  
Vol 211 (4) ◽  
pp. 291-297 ◽  
Author(s):  
B E A Fisher
Keyword(s):  
Cooling Tower ◽  
Industrial Process ◽  
Local Environment ◽  
Meteorological Conditions ◽  
Performance Criteria ◽  
Plume Dispersion ◽  
Cooling Towers ◽  
Atmospheric Conditions ◽  
Operating Characteristics

An assessment of the effects of visible cooling tower plumes on the local environment can be a necessary part of any proposal for a new large industrial process. Predictions of the dispersion of plumes from cooling towers are based on methods developed for chimney emissions. However, the kinds of criteria used to judge the acceptability of cooling tower plumes are different from those used for stack plumes. The frequency of long elevated plumes and the frequency of ground fogging are the two main issues. It is shown that events associated with significant plume visibility are dependent both on the operating characteristics of the tower and on the occurrence of certain meteorological conditions. The dependence on atmospheric conditions is shown to be fairly complex and simple performance criteria based on the exit conditions from the tower are not sufficient for assessments.

Design of Cooling Towers by the Effectiveness-NTU Method

1989 ◽  
Vol 111 (4) ◽  
pp. 837-843 ◽  
Author(s):  
H. Jaber ◽  
R. L. Webb
Keyword(s):  
Heat Exchanger ◽  
Cooling Tower ◽  
Design Method ◽  
Design Methods ◽  
Parallel Flow ◽  
Basic Method ◽  
Cooling Towers ◽  
Flow Configuration ◽  
Heat Exchanger Design

This paper develops the effectiveness-NTU design method for cooling towers. The definitions for effectiveness and NTU are totally consistent with the fundamental definitions used in heat exchanger design. Sample calculations are presented for counter and crossflow cooling towers. Using the proper definitions, a person competent in heat exchanger design can easily use the same basic method to design a cooling tower of counter, cross, or parallel flow configuration. The problems associated with the curvature of the saturated air enthalpy line are also treated. A “one-increment” design ignores the effect of this curvature. Increased precision can be obtained by dividing the cooling range into two or more increments. The standard effectiveness-NTU method is then used for each of the increments. Calculations are presented to define the error associated with different numbers of increments. This defines the number of increments required to attain a desired degree of precision. The authors also summarize the LMED method introduced by Berman, and show that this is totally consistent with the effectiveness-NTU method. Hence, using proper and consistent terms, heat exchanger designers are shown how to use either the standard LMED or effectiveness-NTU design methods to design cooling towers.

scholarly journals Elemental ratio measurements of organic compounds using aerosol mass spectrometry: characterization, improved calibration, and implications

2015 ◽  
Vol 15 (1) ◽  
pp. 253-272 ◽  
Author(s):  
M. R. Canagaratna ◽  
J. L. Jimenez ◽  
J. H. Kroll ◽  
Q. Chen ◽  
S. H. Kessler ◽  
...  
Keyword(s):  
High Resolution ◽  
Vacuum Ultraviolet ◽  
Laboratory Data ◽  
Detailed Examination ◽  
Relative Difference ◽  
Data Set ◽  
Elemental Ratios ◽  
Standard Data ◽  
Aerosol Mass ◽  
Relative Errors

Abstract. Elemental compositions of organic aerosol (OA) particles provide useful constraints on OA sources, chemical evolution, and effects. The Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) is widely used to measure OA elemental composition. This study evaluates AMS measurements of atomic oxygen-to-carbon (O : C), hydrogen-to-carbon (H : C), and organic mass-to-organic carbon (OM : OC) ratios, and of carbon oxidation state (OS C) for a vastly expanded laboratory data set of multifunctional oxidized OA standards. For the expanded standard data set, the method introduced by Aiken et al. (2008), which uses experimentally measured ion intensities at all ions to determine elemental ratios (referred to here as "Aiken-Explicit"), reproduces known O : C and H : C ratio values within 20% (average absolute value of relative errors) and 12%, respectively. The more commonly used method, which uses empirically estimated H2O+ and CO+ ion intensities to avoid gas phase air interferences at these ions (referred to here as "Aiken-Ambient"), reproduces O : C and H : C of multifunctional oxidized species within 28 and 14% of known values. The values from the latter method are systematically biased low, however, with larger biases observed for alcohols and simple diacids. A detailed examination of the H2O+, CO+, and CO2+ fragments in the high-resolution mass spectra of the standard compounds indicates that the Aiken-Ambient method underestimates the CO+ and especially H2O+ produced from many oxidized species. Combined AMS–vacuum ultraviolet (VUV) ionization measurements indicate that these ions are produced by dehydration and decarboxylation on the AMS vaporizer (usually operated at 600 °C). Thermal decomposition is observed to be efficient at vaporizer temperatures down to 200 °C. These results are used together to develop an "Improved-Ambient" elemental analysis method for AMS spectra measured in air. The Improved-Ambient method uses specific ion fragments as markers to correct for molecular functionality-dependent systematic biases and reproduces known O : C (H : C) ratios of individual oxidized standards within 28% (13%) of the known molecular values. The error in Improved-Ambient O : C (H : C) values is smaller for theoretical standard mixtures of the oxidized organic standards, which are more representative of the complex mix of species present in ambient OA. For ambient OA, the Improved-Ambient method produces O : C (H : C) values that are 27% (11%) larger than previously published Aiken-Ambient values; a corresponding increase of 9% is observed for OM : OC values. These results imply that ambient OA has a higher relative oxygen content than previously estimated. The OS C values calculated for ambient OA by the two methods agree well, however (average relative difference of 0.06 OS C units). This indicates that OS C is a more robust metric of oxidation than O : C, likely since OS C is not affected by hydration or dehydration, either in the atmosphere or during analysis.

Analysis of Heat, Mass, and Momentum Transfer in the Rain Zone of Counterflow Cooling Towers

1999 ◽  
Vol 121 (4) ◽  
pp. 751-755 ◽  
Author(s):  
E. de Villiers ◽  
D. G. Kro¨ger
Keyword(s):  
Momentum Transfer ◽  
Cooling Tower ◽  
Mechanical Energy ◽  
Performance Evaluations ◽  
Cooling Towers ◽  
Droplet Deformation ◽  
One Dimensional ◽  
Mechanical Energy Loss ◽  
Simplifying Assumptions ◽  
Semi Empirical

The rate of heat, mass, and momentum transfer in the rain zone of three counterflow cooling tower geometries is analyzed using simplifying assumptions and numerical integration. The objective of the analysis is to generate equations for use in a one-dimensional mathematical cooling tower performance evaluations. Droplet deformation is taken into account and momentum transfer is calculated from the air flow’s mechanical energy loss, caused by air-droplet interaction. A comparison of dimensionless semi-empirical equations and experimental data demonstrates the method’s capability to predict the pressure drop in a counterflow rain zone.

Inovasi Pengolahan Limbah Cair Batik dengan IPAL Ekonomis di Desa Maos Kidul Cilacap

2021 ◽  
Vol 3 (2) ◽  
pp. 36-42
Author(s):  
Theresia Evila Purwanti Sri Rahayu ◽  
Rosita Dwityaningsih ◽  
Murni Handayani ◽  
Khoeruddin Witriansyah ◽  
Ayu Pramita
Keyword(s):  
Wastewater Treatment ◽  
Total Suspended Solid ◽  
Suspended Solid ◽  
Business Owners ◽  
Solid Particles ◽  
Hazardous Substances ◽  
Pollutant Concentrations ◽  
Service Project ◽  
Hazardous Metal ◽  
Dark Blue

Wastewater resulted from the batik dying process is known for its environmentally hazardous substances including hazardous natural and synthetic organic matter, suspended particles, and hazardous metal. But in the micro and medium scale batik textile business, wastewater treatment is mostly not carried because it does not give benefit for the owner. Economical wastewater treatment constructions can be an alternative for the business owner for their free operational cost. Batik wastewater treatment ought to be carried out to meet government standards but most importantly to decrease hazardous pollutant’s concentrations so it does not harm the environment. This society service project aims to provide alternatively economical wastewater treatment for batik business owners by applying simples and cheapest yet effective treatment methods to reduce pollutant concentrations in wastewater. Methods applied in this project including sedimentation, filtration, and landfill-bioremediation. The laboratorium analysis result shows that sedimentation and filtration are significantly reduced total suspended solid particles in wastewater from 2450 to 100 mg/L in line with wastewater decoloring from dark blue to clear yellow.

Sign in / Sign up

Export Citation Format

Share Document