scholarly journals Safe Operation Conditions of Electrical Power System Considering Power Balanceability Among Power Generators, Loads, and Storage Devices

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4460
Author(s):  
Saher Javaid ◽  
Mineo Kaneko ◽  
Yasuo Tan
Keyword(s):  
Power Flow ◽  
Flow Direction ◽  
Storage Device ◽  
Flow Paths ◽  
Power Generators ◽  
Storage Devices ◽  
Flow Assignment ◽  
System Characterization ◽  
Power Storage ◽  
Dependent Flow

The introduction of an energy storage system plays a vital role in the integration of renewable energy by keeping a stable operation and enhancing the flexibility of the power flow system, especially for an islanding microgrid which is not tied to a grid and for a self-contained microgrid which tries to stay independent from a grid as much as possible. To accommodate the effects of power fluctuations of distributed energy resources and power loads on power systems, a power flow assignment under power balance constraint is essential. However, due to power limitations of power devices, the capacity of storage devices, and power flow connections, the power balance may not be achieved. In this paper, we proposed a system characterization which describes the relation among power generators, power loads, power storage devices, and connections that must be satisfied for a system to operate by keeping SOC limitations of power storage devices. When we consider one power generator, one power load, and one power storage device connected at a single node, the generated energy by the generator minus the consumed energy by the load from some start time will increase/decrease the state of charge (SOC) for the storage device; hence, keeping SOC max/min limitations relies on whether the difference between the generated energy and the consumed energy stays within a certain range or not, which can be computed from the capacity Ess and other parameters. Our contribution in this paper is an extension and generalization of this observation to a system that consists of multiple fluctuating power generators, multiple fluctuating power loads, multiple storage devices, and connections that may not be a full connection between all devices. By carefully enumerating the connection-dependent flow paths of generated energy along the flow direction from generators to storages and loads, and enumerating the connection-dependent flow paths of consumed energy along the counter-flow direction from loads to storages and generators, we have formulated the increase/decrease of SOCs of storage devices caused by the imbalance between generated energy and consumed energy. Finally, considering the max/min limitations of SOCs and fluctuations of power generators and power loads, the conditions that the power generators and the power loads must have for SOCs of storage devices to maintain individual max/min limitations have been derived. The system characterization provides guidelines for a power flow system that can continue safe operation in the presence of power fluctuations. That is, in order for a system to have a feasible power flow assignment, there are the issues of how large the capacity of a power storage device should be, how large/small the maximum/minimum power/demand levels of the power generators and the power loads should be, and how the connection should be configured. Several examples using our system characterization are demonstrated to show the possible applications of our results.

An intelligent and portable power storage device able to visualize the energy status

2019 ◽  
Vol 7 (40) ◽  
pp. 23028-23037 ◽  
Author(s):  
Lei Liu ◽  
Qianqian Zhang ◽  
Kai Du ◽  
Zhibing He ◽  
Tao Wang ◽  
...  
Keyword(s):  
Energy Storage ◽  
Storage Device ◽  
Energy Status ◽  
Storage Devices ◽  
Full Cell ◽  
Portable Power ◽  
Power Storage

Electrochromic power storage devices integrate energy storage and electrochromic behavior into a single full cell that can enable the visualization of the energy status by the naked eyes.

scholarly journals Cooperative optimal configuration of electricity storage and heat storage based on particle swarm optimization

2021 ◽  
Vol 257 ◽  
pp. 01014
Author(s):  
Te Cheng ◽  
Fei Xu ◽  
Ling Hao ◽  
Lei Chen ◽  
Qun Chen ◽  
...  
Keyword(s):  
Heat Storage ◽  
Operation Mode ◽  
Particle Swarm ◽  
Optimal Solution ◽  
Economic Benefits ◽  
Storage Device ◽  
Particle Swarm Algorithm ◽  
Electricity Storage ◽  
Storage Devices ◽  
Power Storage

During the heating season in my country’s Three Norths, the operation mode of “using heat to determine electricity” for cogeneration units has made the “wind curtailment rate” high. Electricity storage and heat storage are both important ways to solve this problem. In order to determine the optimal power and capacity of heat storage and power storage devices, this paper proposes a two-layer optimization model that considers the economic benefits of the entire system and the life of the power storage device is affected by its operation. Comsidering the iterative life of the power storage device, the optimal solution for the power, capacity and location of the heat storage and power storage device is obtained by using the particle swarm algorithm. Finally, the actual data of the IEEE classic 33-node system verifies the effectiveness of the proposed method.

scholarly journals Ionic Liquid Electrolytes for Electrochemical Energy Storage Devices

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4000
Author(s):  
Eunhwan Kim ◽  
Juyeon Han ◽  
Seokgyu Ryu ◽  
Youngkyu Choi ◽  
Jeeyoung Yoo
Keyword(s):  
Ionic Liquid ◽  
Energy Storage ◽  
Lithium Ion ◽  
Electrochemical Energy Storage ◽  
Storage Device ◽  
Energy Storage Device ◽  
Energy Storage Devices ◽  
Storage Devices ◽  
Storage Ability ◽  
Electrochemical Energy

For decades, improvements in electrolytes and electrodes have driven the development of electrochemical energy storage devices. Generally, electrodes and electrolytes should not be developed separately due to the importance of the interaction at their interface. The energy storage ability and safety of energy storage devices are in fact determined by the arrangement of ions and electrons between the electrode and the electrolyte. In this paper, the physicochemical and electrochemical properties of lithium-ion batteries and supercapacitors using ionic liquids (ILs) as an electrolyte are reviewed. Additionally, the energy storage device ILs developed over the last decade are introduced.

scholarly journals Progresses in Analytical Design of Distribution Grids and Energy Storage

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4270
Author(s):  
Gianpiero Colangelo ◽  
Gianluigi Spirto ◽  
Marco Milanese ◽  
Arturo de Risi
Keyword(s):  
Renewable Energy ◽  
Power Flow ◽  
State Of The Art ◽  
Renewable Energy Sources ◽  
Energy Sources ◽  
Distribution Grid ◽  
Mathematical Methods ◽  
Power Generators ◽  
Bidirectional Power Flow ◽  
Distribution Grids

In the last years, a change in the power generation paradigm has been promoted by the increasing use of renewable energy sources combined with the need to reduce CO2 emissions. Small and distributed power generators are preferred to the classical centralized and sizeable ones. Accordingly, this fact led to a new way to think and design distributions grids. One of the challenges is to handle bidirectional power flow at the distribution substations transformer from and to the national transportation grid. The aim of this paper is to review and analyze the different mathematical methods to design the architecture of a distribution grid and the state of the art of the technologies used to produce and eventually store or convert, in different energy carriers, electricity produced by renewable energy sources, coping with the aleatory of these sources.

scholarly journals Implications of NVM Based Storage on Memory Subsystem Management

2020 ◽  
Vol 10 (3) ◽  
pp. 999
Author(s):  
Hyokyung Bahn ◽  
Kyungwoon Cho
Keyword(s):  
Random Access ◽  
Disk Drive ◽  
Main Memory ◽  
Memory Storage ◽  
Storage Device ◽  
Storage Devices ◽  
Large Memory ◽  
Memory Subsystems ◽  
Non Volatile Memory ◽  
Management Techniques

Recently, non-volatile memory (NVM) has advanced as a fast storage medium, and legacy memory subsystems optimized for DRAM (dynamic random access memory) and HDD (hard disk drive) hierarchies need to be revisited. In this article, we explore the memory subsystems that use NVM as an underlying storage device and discuss the challenges and implications of such systems. As storage performance becomes close to DRAM performance, existing memory configurations and I/O (input/output) mechanisms should be reassessed. This article explores the performance of systems with NVM based storage emulated by the RAMDisk under various configurations. Through our measurement study, we make the following findings. (1) We can decrease the main memory size without performance penalties when NVM storage is adopted instead of HDD. (2) For buffer caching to be effective, judicious management techniques like admission control are necessary. (3) Prefetching is not effective in NVM storage. (4) The effect of synchronous I/O and direct I/O in NVM storage is less significant than that in HDD storage. (5) Performance degradation due to the contention of multi-threads is less severe in NVM based storage than in HDD. Based on these observations, we discuss a new PC configuration consisting of small memory and fast storage in comparison with a traditional PC consisting of large memory and slow storage. We show that this new memory-storage configuration can be an alternative solution for ever-growing memory demands and the limited density of DRAM memory. We anticipate that our results will provide directions in system software development in the presence of ever-faster storage devices.

scholarly journals Layered double hydroxide membrane with high hydroxide conductivity and ion selectivity for energy storage device

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Jing Hu ◽  
Xiaomin Tang ◽  
Qing Dai ◽  
Zhiqiang Liu ◽  
Huamin Zhang ◽  
...  
Keyword(s):  
Energy Storage ◽  
High Performance ◽  
Ion Selectivity ◽  
Storage Device ◽  
Hydroxyl Groups ◽  
Flow Battery ◽  
Energy Storage Devices ◽  
Storage Devices ◽  
Ions Transport ◽  
Double Hydroxides

AbstractMembranes with fast and selective ions transport are highly demanded for energy storage devices. Layered double hydroxides (LDHs), bearing uniform interlayer galleries and abundant hydroxyl groups covalently bonded within two-dimensional (2D) host layers, make them superb candidates for high-performance membranes. However, related research on LDHs for ions separation is quite rare, especially the deep-going study on ions transport behavior in LDHs. Here, we report a LDHs-based composite membrane with fast and selective ions transport for flow battery application. The hydroxide ions transport through LDHs via vehicular (standard diffusion) & Grotthuss (proton hopping) mechanisms is uncovered. The LDHs-based membrane enables an alkaline zinc-based flow battery to operate at 200 mA cm−2, along with an energy efficiency of 82.36% for 400 cycles. This study offers an in-depth understanding of ions transport in LDHs and further inspires their applications in other energy-related devices.

Nonlinear Stochastic Feedback Controllers for Vibratory Energy Harvesters With Power Flow Constraints

2011 ◽  
Author(s):  
Ian L. Cassidy ◽  
Jeffrey T. Scruggs ◽  
Sam Behrens
Keyword(s):  
Power Generation ◽  
Power Flow ◽  
Flow Direction ◽  
Average Power ◽  
Control Input ◽  
Stochastic Disturbances ◽  
Feedback Controllers ◽  
Energy Harvesters ◽  
System States ◽  
Feedback Laws

This study addresses the formulation of feedback controllers for stochastically-excited vibratory energy harvesters. Maximizing power generation from stochastic disturbances can be accomplished using LQG control theory, with the transducer current treated as the control input. For the case where the power flow direction is unconstrained, an electronic drive capable of extracting as well as delivering power to the transducer is required to implement the optimal controller. It is demonstrated that for stochastic disturbances characterized by second-order, bandpass-filtered white noise, energy harvesters can be passively tuned such that optimal stationary power generation only requires half of the system states for feedback in the active circuit. However, there are many applications where the implementation of a bi-directional power electronic drive is infeasible, due to the higher parasitic losses they must sustain. If the electronics are designed to be capable of only single-directional power flow (i.e., where the electronics are incapable of power injection), then these parasitics can be reduced significantly, which makes single-directional converters more appropriate at smaller power scales. The constraint on the directionality of power flow imposes a constraint on the feedback laws that can be implemented with such converters. In this paper, we present a sub-optimal nonlinear control design technique for this class of problems, which exhibits an analytically computable upper bound on average power generation.

Meshing Efficiency Analysis of Two Degree-of-Freedom Epicyclic Gear Trains

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Essam Lauibi Esmail
Keyword(s):  
Reference Frame ◽  
Power Efficiency ◽  
Power Flow ◽  
Flow Direction ◽  
Efficiency Analysis ◽  
Degree Of Freedom ◽  
Gear Train ◽  
Epicyclic Gear ◽  
Gear Trains ◽  
Two Degree Of Freedom

The concept of potential power efficiency is introduced as the efficiency of an epicyclic gear train (EGT) measured in any moving reference frame. The conventional efficiency can be computed in a carrier-moving reference frame in which the gear carrier appears relatively fixed. In principle, by attaching the reference frame to an appropriate link, torques can be calculated with respect to each input, output, or (relatively) fixed link in the EGT. Once the power flow direction is obtained from the potential power ratio, the torque ratios are obtained from the potential power efficiencies, the particular expression of the efficiency of the EGT is found in a simple manner. A systematic methodology for the efficiency analysis of one and two degree-of-freedom (DOF) EGTs is described, and 14 ready-to-use efficiency formulas are derived for 2DOF gear pair entities (GPEs). This paper includes also a discussion on the redundancy of the efficiency formulas used for 1DOF GPEs. An incomplete in the efficiency formulas in previous literature, which make them susceptible to wrong application, is brought to light.

scholarly journals Layered double hydroxide membrane with high hydroxide conductivity and ion selectivity for energy storage device

2020 ◽  
Author(s):  
Jing Hu ◽  
Xiaomin Tang ◽  
Qing Dai ◽  
Zhiqiang Liu ◽  
Huamin Zhang ◽  
...  
Keyword(s):  
Energy Storage ◽  
High Performance ◽  
Ion Selectivity ◽  
Storage Device ◽  
Hydroxyl Groups ◽  
Flow Battery ◽  
Energy Storage Devices ◽  
Storage Devices ◽  
Ions Transport ◽  
Double Hydroxides

Abstract Membranes with fast and selective ions transport are highly demanded for energy storage devices. Layered double hydroxides (LDHs), bearing uniform interlayer galleries and abundant hydroxyl groups covalently bonded within two-dimensional (2D) host layers, make them superb candidates for high-performance membranes. However, related research on LDHs for ions separation is quite rare, especially the deep-going study on ions transport behavior in LDHs. Here, we report a LDHs-based composite membrane with fast and selective ions transport for flow battery application. The hydroxide ions transport through LDHs via vehicular (standard diffusion) & Grotthuss (proton hopping) mechanisms is uncovered. The LDHs-based membrane enables an alkaline zinc-based flow battery to operate at 200 mA cm− 2, along with an energy efficiency of 82.36% for 400 cycles, which is among the highest efficiencies for zinc-based flow batteries. This study offers an in-depth understanding of ions transport in LDHs and further inspires their applications in other energy-related devices.

Sign in / Sign up

Export Citation Format

Share Document