scholarly journals Numerical Analysis on the Performance of a Radiant Cooling Panel with Serpentine-Based Design

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4744
Author(s):  
Mohammad Hakim Mohd Radzai ◽  
Chong Tak Yaw ◽  
Chin Wai Lim ◽  
Siaw Paw Koh ◽  
Nur Amirani Ahmad
Keyword(s):  
Pressure Drop ◽  
Cooling Capacity ◽  
Operating Conditions ◽  
Dew Point ◽  
Cooling Power ◽  
Full Potential ◽  
Ansys Fluent ◽  
Cooling Performance ◽  
Flow Configuration ◽  
Radiant Cooling

Radiant cooling systems (RCS) are gaining acceptance as a heating, ventilation, and air conditioning (HVAC) solution for achieving adequate thermal comfort and maintaining acceptable indoor air quality inside buildings. RCS are well known for their energy-saving potential; however, serious condensation problem hinders the growth of this technology. In order to prevent the risk of condensation, the supply water temperature is kept higher than the dew point temperature of the air inside the room. The full potential of the cooling power of a radiant cooling panel is limited. Therefore, this article is on maximizing the cooling capacity of a radiant cooling panel, in terms of flow configuration. Radiant cooling panels (RCP) with different chilled water pipe configurations are designed and compared, side by side with the conventional serpentine flow configuration. The cooling performance of the radiant cooling panels is evaluated by using computational fluid dynamics (CFD) with Ansys Fluent software (Ansys 2020 R2, PA, USA). Under similar flow and operating conditions, the common serpentine flow configuration exhibits the least effective cooling performance, with the highest pressure drop across the pipe. It is concluded that the proposed designs have the potential of improving the overall efficiency of RCP in terms of temperature distribution, cooling capacity, and pressure drop.

Performance Investigation of Single Adsorption Refrigeration System Driven by Solar Heat Storage

2018 ◽  
Vol 26 (03) ◽  
pp. 1850025
Author(s):  
Hicham Boushaba ◽  
Abdelaziz Mimet
Keyword(s):  
System Performance ◽  
Heat Storage ◽  
Cooling Capacity ◽  
Operating Conditions ◽  
Coefficient Of Performance ◽  
Solar Irradiation ◽  
Cooling Power ◽  
Condensation Temperature ◽  
Adsorption Refrigeration ◽  
Solar Heat

The aim of this paper is to provide a global study of an adsorption refrigeration machine driven by solar heat storage and collected by parabolic trough collector. The system operates with ammonia (as refrigerant) and activated carbon (as adsorbent). A mathematical model interpreting the progression of the heat and the mass transfer at each element of the prototype has been developed. The solar irradiation and the real ambient temperature variations corresponding to a usual summer day in Tetouan (Morocco) are considered. The system performance is evaluated trough specific cooling power (SCP) as well as solar coefficient of performance (SCOP), which was estimated by a dynamic simulation cycle. The pressure, temperature and adsorbed mass profiles in the Adsorber have been calculated. The effects of significant design and operating parameters on the system performance have been investigated. The results show the capability of our system to realize an encouraging performance and to overcome the intermittence of the adsorption refrigeration machines. For a daily solar irradiation of 18[Formula: see text]MJ[Formula: see text]m[Formula: see text] and operating conditions of evaporation temperature [Formula: see text]C, condensation temperature [Formula: see text]C and generation temperature [Formula: see text]C, the results show that the process could achieve an SCP of 115[Formula: see text]W[Formula: see text]kg[Formula: see text] and it could produce a daily specific cooling capacity of 3310[Formula: see text]kJ[Formula: see text]kg[Formula: see text], whereas its SCOP could attain 0.141.

Enhanced Thermoelectric Cooler for On-Chip Hot Spot Cooling

2007 ◽  
Author(s):  
Peng Wang ◽  
Avram Bar-Cohen ◽  
Bao Yang
Keyword(s):  
Hot Spot ◽  
Heat Fluxes ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Cooling Power ◽  
Thermoelectric Cooler ◽  
Thermoelectric Coolers ◽  
Cooling Performance ◽  
Spot Cooling ◽  
On Chip

Due to shrinking feature size and increasing transistor density, combined with the performance demanded from next-generation microprocessors, on-chip hot spots, with their associated high heat fluxes and sharp temperature gradients, have emerged as the primary driver for thermal management of today’s IC technology. This paper describes the novel use of thermoelectric coolers for on-chip hot spot cooling through the use of a copper mini-contact pad, which connects the thermoelectric cooler and the silicon chip thus concentrating the thermoelectric cooling power. A package-level numerical simulation is developed to predict the local on-chip hot spot cooling performance which can be achieved with such mini-contacts. Attention is focused on the hot spot temperature reduction associated with variations in mini-contact size and the thermoelectric element thickness, as well as the parasitic effect of the thermal contact resistance introduced by the mini-contact enhanced TEC. This numerical model and simulation results are validated by comparison to spot cooling experiments with a uniformly heated chip serving as the test vehicle. The experimental results demonstrate that a copper mini-contact pad can improve spot cooling performance by 80 ∼ 115% on a 500μm thick silicon chip under optimum operating conditions and that larger power dissipation on the chip leads to better spot cooling performance.

scholarly journals Numerical Simulation of Passive Cooling Beam and Its Optimization to Increase the Cooling Power

Processes ◽  
2021 ◽  
Vol 9 (8) ◽  
pp. 1478
Author(s):  
Katarína Kaduchová ◽  
Richard Lenhard
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Mathematical Model ◽  
Significant Influence ◽  
Cooling Capacity ◽  
Passive Cooling ◽  
Cooling Power ◽  
Geometrical Parameters ◽  
Confined Space ◽  
Cooling Performance

This article is focused on the research of passive cooling beams and increasing their cooling capacity. A passive cooling beam with four tubes was chosen as a model. A mathematical model was built using the corresponding criterion equations to capture the behavior of a passive cooling beam. This mathematical model can be used to optimize geometrical parameters (the distance between the ribs, rib height and thickness, and diameter and number of tubes), by changing these geometric parameters we can increase the cooling performance. The work includes a mathematical model for calculating the boundary layer, which has a significant influence on the cooling performance. The results obtained from the created mathematical model show that the model works correctly and can be used to optimize the cooling performance of passive cooling beams. To better understand the behavior of a passive cooling beam in a confined space, the entire device was numerically simulated, as was the flow in the intercostal space.

Nocturnal Cooling of Water as Free Cooling Source for Building Indoor Radiant Cooling in Malaysian Climate

2016 ◽  
Vol 833 ◽  
pp. 94-101
Author(s):  
Muhammad Syukri Imran ◽  
Azhaili Baharun ◽  
Siti Halipah Ibrahim ◽  
Wan Azlan bin Wan Zainal Abidin
Keyword(s):  
Cooling System ◽  
Operating Temperature ◽  
Dew Point ◽  
Wave Radiation ◽  
Cooling Power ◽  
Test Model ◽  
Dew Point Temperature ◽  
Long Wave ◽  
Radiant Cooling ◽  
Free Cooling

Normally mechanical chiller supplies chill water temperature at a higher operating temperature to charge a radiant cooling system in building. Other source of cooling is possible since the operating temperature for radiant cooling is limited by the air dew point temperature. This study investigates cooling of water through long wave radiation to the night sky in Kuching Sarawak, Malaysia and utilise this water for radiant cooling purpose. Mathematical model were developed to predict the cooling power of the nocturnal cooling over typical metal roof and was compared to an experimental data. The measurement from the test model verified the predicted data and a yearly potential from nocturnal cooling in this region was established. The amount of cooled water generated from this night cooling system was also calculated. Results showed that an average of 73 W/m2 nocturnal cooling power is possible in this region.

scholarly journals Evaporator Optimization of Refrigerator Systems Using Quality Analysis

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 555
Author(s):  
Sangkyung Na ◽  
Sanghun Song ◽  
Seunghyuk Lee ◽  
Jehwan Lee ◽  
Hyun Kim ◽  
...  
Keyword(s):  
Power Consumption ◽  
Operating Time ◽  
Cooling Capacity ◽  
Operating Conditions ◽  
Quality Analysis ◽  
Lubricating Oil ◽  
Optimal Operating ◽  
Compressor Piston ◽  
Refrigerator Temperature ◽  
Visualization Experiments

In this study, evaporator optimization, via both experimental and simulation methods was conducted. To evaluate the evaporator performance, under the optimal system, the compressor operating time and the effects of oil on the refrigerator system were studied. If the temperature of the refrigerator chamber reaches the setting value, the compressor stops working and it leads to the temperature of the refrigerator chamber slowly increasing, due to the heat transfer to the ambient. When the refrigerator temperature is out of the setting range, the compressor works again, and the refrigerator repeats this process until the end of its life. These on/off period can be controlled through the compressor piston movement. To determine the optimal compressor operating conditions, experiments of monthly power consumption were conducted under various compressor working times and the lowest power consumption conditions was determined when the compressor worked continuously. Lubricating oil, the refrigerator system, using oil, also influenced the system performance. To evaluate the effect of oil, oil eliminated and oil systems were compared based on cooling capacity and power consumption. The cooling capacity of the oil eliminated system was 2.6% higher and the power consumption was 3.6% lower than that of the oil system. After determining the optimal operating conditions of the refrigerator system, visualization experiments and simulations were conducted to decide the optimal evaporator and the conventional evaporator size can be reduced by approximately 2.9%.

scholarly journals Developing a Cold Accumulator with a Capsule Bed Containing Water as a Phase-Change Material

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2703
Author(s):  
Robert Sekret ◽  
Przemysław Starzec
Keyword(s):  
Energy Efficiency ◽  
Heat Pump ◽  
Cold Storage ◽  
Cooling Capacity ◽  
Cooling Power ◽  
Storage Process ◽  
Water Ice ◽  
Measurement Results ◽  
Mathematical Relationships ◽  
Change Material

The paper presents the investigation of a prototype cold accumulator using water–ice latent heat for the cold storage process. The concept of the cold accumulator was based on a 200-L-capacity cylindrical storage tank in which spherical capsules filled with water were placed. Beds of polypropylene capsules with diameters of 80 mm, 70 mm, and 60 mm were used in the tests. The cold accumulator operated with a water–air heat pump. Based on the test results, the following parameters were calculated: the cooling capacity, cooling power, energy efficiency of the cold storage, and energy efficiency ratio (EER) of the accumulator. The obtained measurement results were described with mathematical relationships (allowing for measurement error) using criterial numbers and the developed “Research Stand Factor Number” (RSFN) index. It has been found that, for the prototype cold accumulator under investigation, the maximum values of the cooling capacity (17 kWh or 85.3 kWh per cubic meter of the accumulator), energy efficiency (0.99), and EER (4.8) occur for an RSFN of 144·10−4. The optimal conditions for the operation of the prototype cold accumulator were the closest to laboratory tests conducted for a bed with capsules with a diameter of 70 mm and a mass flow of the water–glycol mixture flowing between the accumulator and the heat pump of 0.084 kg/s. During the tests, no significant problems with the operation of the prototype cold accumulator were found.

Determination of cost-efficient cooling power range for improving the performance of internally cooled ultrasonic atomization liquid desiccant dehumidifiers

2020 ◽  
Vol 29 (9) ◽  
pp. 1260-1276
Author(s):  
Zili Yang ◽  
Lu-An Chen ◽  
Ruiyang Tao ◽  
Ke Zhong
Keyword(s):  
Power Efficiency ◽  
Removal Rate ◽  
Operating Conditions ◽  
Cooling Power ◽  
Internal Cooling ◽  
Liquid Desiccant ◽  
Improvement Rate ◽  
Ultrasonic Atomization ◽  
Internally Cooled ◽  
Cost Efficient

Liquid desiccant dehumidifiers (LDDs) can be improved by adding internal cooling. However, the addition of excessive cooling power may deteriorate the system‘s cost-efficiency, whereas the addition of insufficient cooling power leads to negligible performance improvements. The objective of this study is to determine the suitable cost-efficient cooling power range for improving the performance of internally cooled LDDs (IC-LDDs). A novel method and a set of criteria related to the moisture removal rate, cooling-power efficiency ( ηc) and coefficient of dehumidification performance from cooling power ( DCOPcooling) were proposed to determine cost-efficient cooling power. The internally cooled ultrasonic atomization liquid desiccant system (IC-UADS), together with a well-validated model based on the conservation laws of mass and energy and the sensible heat balance, was adopted to demonstrate the analysis. The results showed that, although the dehumidification performance improves with increasing cooling power, the improvement rate decreases, while ηcand DCOPcoolingdecline quickly (by 87.9%). For cost-efficient improvement, the necessary power proportion of internal cooling to the system‘s target dehumidification capacity tends to be stable, which was about 29% for the IC-UADS, and independent of the operating conditions. The results may help to determine the reasonable cooling power range for cost-efficient improvement of IC-LDDs.

ASU Simulation in Separating Air Components by Refrigeration Distillation (Oxygen and Nitrogen) Using ASPEN HYSYS (Case Study: SIAD Company)

2020 ◽  
Vol 15 (3) ◽  
Author(s):  
Afshar Alihosseini
Keyword(s):  
Cooling Capacity ◽  
Air Separation ◽  
Cooling Power ◽  
Distillation Tower ◽  
Aspen Hysys ◽  
Expansion Turbine ◽  
Gas Products ◽  
Utility Services ◽  
Petrochemical Industries

AbstractCurrently, air separation units (ASUs) have become very important in various industries, particularly oil and petrochemical industries which provide feed and utility services (oxygen, nitrogen, etc.). In this study, a new industrial ASU was evaluated by collecting operational and process information needed by the simulator by means of HYSYS software (ASPEN-ONE). The results obtained from this simulator were analyzed by ASU data and its error rate was calculated. In this research, the simulation of ASU performance was done in the presence of an expansion turbine in order to provide pressure inside the air distillation tower. Likewise, the cooling capacity of the cooling compartment and the data were analysed. The results indicated that expansion turbine is costly effective. Notably, it not only reduces the energy needed to compress air and supply power of the equipment, but also provides more cooling power and reduces air temperature. Moreover, turbines also increase the concentration of lighter gas products, namely nitrogen.

Flow Coefficient Evaluation of Poppet Valves Used in Reciprocating Compressors for LDPE

2008 ◽  
Author(s):  
Enzo Giacomelli ◽  
Massimo Schiavone ◽  
Fabio Manfrone ◽  
Andrea Raggi
Keyword(s):  
Pressure Drop ◽  
Time Pressure ◽  
Experimental Tests ◽  
Operating Conditions ◽  
Flow Coefficient ◽  
Operating Life ◽  
High Fatigue ◽  
Strongly Connected ◽  
And Performance ◽  
Poppet Valves

Poppet valves have been used for a long time for very high pressure reciprocating compressors, as for example in the case of Low Density Polyethylene. These applications are very critical because the final pressure can reach 350 MPa and the evaluation of the performance of the machines is strongly connected to the proper operation and performance of the valve itself. The arrangement of cylinders requires generally a certain compactness of valve to withstand high fatigue stresses, but at the same time pressure drop and operating life are very important. In recent years the reliability of the machines has been improving over and over and the customers’ needs are very stringent. Therefore the use of poppet valves has been extended to other cases. In general the mentioned applications are heavy duty services and the simulation of the valves require some coefficients to be used in the differential equations, able to describe the movement of plate/disk or poppet and the flow and related pressure drop through the valves. Such coefficients are often determined in an experimental way in order to have a simulation closer to the real operating conditions. For the flow coefficients it is also possible today to use theoretical programs capable of determining the needed values in a quick and economical way. Some investigations have been carried out to determine the values for certain geometries of poppet valves. The results of the theory have been compared with some experimental tests. The good agreement between the various methods indicates the most suitable procedure to be applied in order to have reliable data. The advantage is evident as the time necessary for the theoretical procedure is faster and less expensive. This is of significant importance at the time of the design and also in case of a need to provide timely technical support for the operating behavior of the valves. Particularly for LDPE, the optimization of all the parameters is strongly necessary. The fatigue stresses of cylinder heads and valve bodies have to match in fact with gas passage turbulence and pressure drop, added to the mechanical behavior of the poppet valve components.

A Transient 3D CFD Model of a Progressive Cavity Pump

2016 ◽  
Author(s):  
K. R. Mrinal ◽  
Md. Hamid Siddique ◽  
Abdus Samad
Keyword(s):  
Oil And Gas ◽  
Complex Geometry ◽  
Transient Behavior ◽  
Oil And Gas Industry ◽  
High Viscosity ◽  
Solid Content ◽  
Operating Conditions ◽  
Cfd Model ◽  
Ansys Fluent ◽  
Flow Variables

A progressive cavity pump (PCP) is a positive displacement pump and has been used as an artificial lift method in the oil and gas industry for pumping fluid with solid content and high viscosity. In a PCP, a single-lobe rotor rotates inside a double-lobe stator. Articles on computational works for flows through a PCP are limited because of transient behavior of flow, complex geometry and moving boundaries. In this paper, a 3D CFD model has been developed to predict the flow variables at different operating conditions. The flow is considered as incompressible, single phase, transient, and turbulent. The dynamic mesh model in Ansys-Fluent for the rotor mesh movement is used, and a user defined function (UDF) written in C language defines the rotor’s hypocycloid path. The mesh deformation is done with spring based smoothing and local remeshing technique. The computational results are compared with the experiment results available in the literature. Thepump gives maximum flowrate at zero differential pressure.

Sign in / Sign up

Export Citation Format

Share Document