scholarly journals Development and Application of a New QuEChERS Method in UHPLC-QqQ-MS/MS to Detect Seven Biogenic Amines in Chinese Wines

Foods ◽  
2019 ◽  
Vol 8 (11) ◽  
pp. 552
Author(s):  
Shun-Yu Han ◽  
Lan-Lan Hao ◽  
Xiao Shi ◽  
Jian-Ming Niu ◽  
Bo Zhang
Keyword(s):  
Biogenic Amines ◽  
Storage Time ◽  
Limit Of Detection ◽  
Pearson Correlation ◽  
High Sensitivity ◽  
Gansu Province ◽  
Grape Variety ◽  
Limit Of Quantification ◽  
Toxic Dose ◽  
Relative Standard

The aim of this study was to develop and validate an improved, simple, and sensitive method for the simultaneous determination of seven types (cadaverine, CAD; hexylamine, HEX; histamine, HIS; phenylethylamine, PEA; putrescine, PUT; tyramine, TYR) of biogenic amines (BAs) in wine matrices. For this reason, a modified QuEChERS combined with ultra-performance liquid chromatography coupled to a triple quadrupole mass spectrometry (UHPLC-QqQ-MS/MS) method was investigated. The optimization of UHPLC-QqQ-MS/MS separation and QuEChERS procedure was performed. Under optimum conditions, the excellent chromatographic performance of the whole separation was accomplished within 6.3 min analyzing time. Meanwhile, the recoveries ranged from 77.2% to 101.7%, while relative standard deviation (RSD) remained between 0.0% and 9.4%. The limit of detection (LOD, 0.50–1.00 µg/L) and the limit of quantification (LOQ, 1.65–3.30 µg/L) were lower than those permitted by legislation in food matrices, which demonstrated the high sensitivity and applicability of this efficient method. This validated method was also applied in a pilot study to analyze BAs in 81 wine samples from Hexi Corridor Region (Gansu Province, Northwest China), CAD, HEX, HIS, PEA, PUT, and TYR were detected to varying degrees in the samples. However, when compared with the existing standards, the BAs in all 81 wine samples did not exceed the prescribed limit value or toxic dose (2–40 mg/L). Moreover, a statistical approach was also conducted using Pearson correlation analysis, and to evaluate their concentrations in terms of wine parameters (storage time, grape variety, wine type, and basic physicochemical index). The results showed that, among the seven kinds of BAs, the concentration of HIS had a certain correlation with alcoholic degree and grape variety. In addition, the level of PEA had a certain correlation with the wine pH and wine storage time. It is worth noting that this seems to be the first report regarding the application of QuEChERS-UHPLC-QqQ-MS/MS in the analysis of BAs in wine in this region.

scholarly journals Simultaneous Analysis of 20 Mycotoxins in Grapes and Wines from Hexi Corridor Region (China): Based on a QuEChERS–UHPLC–MS/MS Method

Molecules ◽  
2018 ◽  
Vol 23 (8) ◽  
pp. 1926 ◽  
Author(s):  
Bo Zhang ◽  
Xia Chen ◽  
Shun-Yu Han ◽  
Min Li ◽  
Teng-Zhen Ma ◽  
...  
Keyword(s):  
Limit Of Detection ◽  
Fumonisin B1 ◽  
Cyclopiazonic Acid ◽  
High Sensitivity ◽  
Hexi Corridor ◽  
Limit Of Quantification ◽  
Ultra High Pressure ◽  
Legal Limits ◽  
Relative Standard ◽  
Aflatoxin B2

The aim of this study is to develop and validate an improved analytical method for the simultaneous quantification of 20 types of mycotoxins in grapes and wines. In this research, the optimization of tandem mass spectrometer (MS/MS) parameter, ultra-high pressure liquid chromatography (UHPLC) separation, and QuEChERS procedure, which includes wine/water ratio, the amount and type of salt, clean-up sorbent, were performed, and the whole separation of mycotoxins was accomplished within 7 min analyzing time. Under optimum conditions, recoveries ranged from 85.6% to 117.8%, while relative standard deviation (RSD) remained between 6.0% and 17.5%. The limit of detection (LOD, 0.06–10 μg/L) and the limit of quantification (LOQ, 0.18–30 μg/L) were lower than those permitted by legislation in food matrices, which demonstrated the high sensitivity and applicability of this efficient method. Finally, 36 grapes and 42 wine samples from the Hexi Corridor region were analyzed. Penicillic acid (PCA), mycophenolic acid (MPA), cyclopiazonic acid (CPA), fumonisin B1 (FB1) and zearalenone (ZEN) were detected in a small number of grape samples with lower concentrations between 0.10 μg/L and 81.26 μg/L. Meanwhile, ochratoxin A (OTA), aflatoxin B2 (AFB2), MPA, CPA, and ZEN were detected in some wine counterparts with concentrations ranged from 0.10 μg/L to 4.62 μg/L. However, the concentrations of the detected mycotoxins were much lower than the maximum legal limits set of other products.

Validation Method on Determination of Chemical Oxygen Demand Using Indirect UV-Vis Spectrometry

2021 ◽  
Vol 1162 ◽  
pp. 101-108
Author(s):  
Yuli Rohyami ◽  
Toni Aprianto ◽  
Marjono
Keyword(s):  
Chemical Oxygen Demand ◽  
Limit Of Detection ◽  
Oxygen Demand ◽  
High Sensitivity ◽  
Limit Of Quantification ◽  
Validation Method ◽  
Relative Standard ◽  
Uncertainty Calculation ◽  
Limit Of Quantitation

The validation method for determination of chemical oxygen demand (COD) with indirect UV-Vis spectrometry have been done. This method enable to easily perform highly sensitive, considerably faster and easier, and minimize the use of digestion solution. This method is the development of standard method of COD determination by closed reflux using UV-Vis spectrometry so it requires the method validation stage. The validation is used to ensure linearity, limit of detection, limit of quantification, precision, and accuracy values in accordance with quality control. This study was also carried out to formulate the uncertainty calculation modeling of COD on water analysis. The result of validation method show that the calibration curve linearity is 0.9994 with the linear regression equation Y = 0.0003X + 0.0005. The method is able to have high sensitivity in measuring COD value with low concentrations with limit of detection and limit of quantitation of 9.78 and 32.59 mg O2/L. Indirect UV-Vis spectrometry has high precision with relative standard deviation of 0.66% and high accuracy with the percentage of recovery of 91.35%. The uncertainty formulation model on determination of COD from the source of standard uncertainty of sample volume, calibration curves, and repeatability.

scholarly journals Method validation and measurement uncertainty of possible thirty volatile organic compounds (VOCs) presented in the polyethylene present in bottled drinking waters sold in Turkey

2020 ◽  
Vol 11 (1) ◽  
Author(s):  
Barış Güzel ◽  
Oltan Canli
Keyword(s):  
Measurement Uncertainty ◽  
Limit Of Detection ◽  
Direct Injection ◽  
High Sensitivity ◽  
Uncertainty Budget ◽  
Gas Chromatography Mass Spectrometry ◽  
Limit Of Quantification ◽  
Drinking Waters ◽  
Relative Standard

Abstract This study was actualized for the simultaneous determination of possible thirty VOCs presented in drinking waters in Turkey by direct injection to purge and trap (PT) gas chromatography-mass spectrometry (GC-MS). It consists of selectivity, linearity, the limit of detection (LOD) and limit of quantification (LOQ), accuracy (recovery), precision, trueness, and measurement uncertainty studies. In linearity, the values of correlation coefficients (r2) for the matrix-matched calibration curves were higher than 0.998 for all analytes. This method showed high sensitivity (LOD: 0.011–0.040 μg/L; LOQ: 0.035–0.133 μg/L), quite sufficient recovery (82.6% to 103.1%) for accuracy, and acceptable precision (intra-day recovery: 81.5–104.4%, relative standard deviation (RSD): 1.04–9.81%; inter-day recovery: 92.6–104.1%, RSD: 1.15–7.52%). All the recovery and RSD values obtained below 10% are evaluated agreeable in point of the AOAC and EURACHEM/CITAC validation guidelines. The recovery percentages of all analytes in CRM changed between 80.3 and 109.9% and the RSD (%) values for each analyte obtained below 10%. The proficiency test results were satisfactory and comparable (z score less than or equal to 2.0 is no questionable or satisfactory) to those obtained by other laboratories participating in the round. The calculated percentage of relative uncertainties for each analyte changed from 2.99 to 10.10% and the major contribution to uncertainty budget arises from the calibration curve and repeatability. Therefore, the results demonstrate that this method is applicable for the determination of possible thirty VOCs in drinking waters in routine analysis for custom laboratories.

Calcium/Copper alginate framework doped with CuO nano-particles as a novel adsorbent for micro-extraction of benzodiazepines from human serum

2020 ◽  
Vol 16 ◽  
Author(s):  
Nadereh Rahbar ◽  
Fatemeh Ahmadi ◽  
Zahra Ramezani ◽  
Masoumeh Nourani
Keyword(s):  
Human Serum ◽  
High Performance ◽  
Limit Of Detection ◽  
Solid Phase ◽  
Nano Particles ◽  
Limit Of Quantification ◽  
Analytical Methodology ◽  
Fiber Fabrication ◽  
Relative Standard ◽  
Green Procedure

Background: Sample preparation is one of the most challenging phases in pharmaceutical analysis, especially in biological matrices, affecting the whole analytical methodology. Objective: In this study, a new Ca(II)/Cu(II)/alginate/CuO nanoparticles hydrogel fiber (CCACHF) was synthesized through a simple, green procedure and applied for fiber micro solid phase extraction (FMSPE) of diazepam (DIZ) and oxazepam (OXZ) as model drugs prior to high-performance liquid chromatography-UV detection (HPLC-UV). Methods: Composition and morphology of the prepared fiber were characterized and the effect of main parameters on the fiber fabrication and extraction efficiency have been studied and optimized. Results: In optimal conditions, calibration curves were linear ranging between 0.1–500 µg L−1 with regression coefficients of 0.9938 and 0.9968. Limit of detection (LOD) (S/N=3) and limit of quantification (LOQ) (S/N=10) of the technique for DIZ and OXZ were 0.03 to 0.1 µg L−1. Within-day and between-day relative standard deviations (RSDs) for DIZ and OXZ were 6.0–12.5% and 3.3–9.4%, respectively. Conclusion: The fabricated adsorbent has been substantially employed to extraction of selected benzo-diazepines (BZDs) from human serum real specimens and the obtained recoveries were also satisfactory (82.1-109.7%).

scholarly journals Stability-indicating HPLC-DAD assay for simultaneous quantification of hydrocortisone 21 acetate, dexamethasone, and fluocinolone acetonide in cosmetics

2020 ◽  
Vol 18 (1) ◽  
pp. 962-973
Author(s):  
Saira Arif ◽  
Sadia Ata
Keyword(s):  
Mobile Phase ◽  
Limit Of Detection ◽  
Fluocinolone Acetonide ◽  
Internal Diameter ◽  
Forced Degradation ◽  
Specific Method ◽  
Regression Equations ◽  
Limit Of Quantification ◽  
Simultaneous Quantification ◽  
Relative Standard

AbstractA rapid and specific method was developed for simultaneous quantification of hydrocortisone 21 acetate (HCA), dexamethasone (DEX), and fluocinolone acetonide (FCA) in whitening cream formulations using reversed-phase high-performance liquid chromatography. The effect of the composition of the mobile phase, analysis temperature, and detection wavelength was investigated to optimize the separation of studied components. The analytes were finally well separated using ACE Excel 2, C18 AR column having 150 mm length, 3 mm internal diameter, and 2 µm particle size at 35°C using methanol with 1% formic acid and double-distilled deionized water in the ratio of 60:40 (v/v), respectively, as the mobile phase in isocratic mode. Ten microliters of sample were injected with a flow rate of 0.5 mL/min. The specificity, linearity, accuracy, precision, recovery, limit of detection (LOD), limit of quantification (LOQ), and robustness were determined to validate the method as per International Conference on Harmonization guidelines. All the analytes were simultaneously separated within 8 min, and observed retention times of HCA, DEX, and FCA were 4.5, 5.5, and 6.9 min, respectively. The proposed method showed good linearity with the correlation coefficient, R2 = 0.999 over the range of 1–150 µg/mL for all standards. The linear regression equations were y = 12.7x + 118.7 (r = 0.999) for HCA, y = 12.9x + 106.8 (r = 0.999) for DEX, and y = 12.9x + 96.8 (r = 0.999) for FCA. The LOD was 0.25, 0.20, and 0.08 µg/mL for HCA, FCA, and DEX and LOQ was 2.06, 1.83, and 1.55 µg/mL for HCA, FCA, and DEX, respectively. The recovery values of HCA, DEX, and FCA ranged from 100.7–101.3, 102.0–102.6, and 100.2–102.0%, respectively, and the relative standard deviation for precision (intra- and interday) was less than 2, which indicated repeatability and reproducibility. The novelty of the method was described by forced degradation experimentation of all analytes in the combined form under acidic, basic, oxidative, and thermal stress. The proposed method was found to be simple, rapid, and reliable for the simultaneous determination of HCA, DEX, and FCA in cosmetics.

scholarly journals A novel LC-MS method development and validation for the determination of phenyl vinyl sulfone in eletriptan hydrobromide

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Indhu Priya Mabbu ◽  
G. Sumathi ◽  
N. Devanna
Keyword(s):  
Method Development ◽  
Limit Of Detection ◽  
Vinyl Sulfone ◽  
Limit Of Quantification ◽  
Relative Standard ◽  
Pressure Chemical Ionization ◽  
Pressure Chemical ◽  
Development And Validation ◽  
Phenyl Vinyl

Abstract Background The aim of the present method is to develop and validate a specific, sensitive, precise, and accurate liquid chromatography-mass spectrometry (LC-MS) method for the estimation of the phenyl vinyl sulfone in the eletriptan hydrobromide. The effective separation of the phenyl vinyl sulfone was achieved by the Symmetry C18 (50 × 4.6 mm, 3.5 μm) column and a mobile phase composition of 0.1%v/v ammonia buffer to methanol (5:95 v/v), using 0.45 ml/min flow rate and 20 μl of injection volume, with methanol used as diluent. The phenyl vinyl sulfone was monitored on atomic pressure chemical ionization mode mass spectrometer with positive polarity mode. Results The retention time of phenyl vinyl sulfone was found at 2.13 min. The limit of detection (LOD) and limit of quantification (LOQ) were observed at 1.43 ppm and 4.77 ppm concentration respectively; the linear range was found in the concentration ranges from 4.77 to 27.00 ppm with regression coefficient of 0.9990 and accuracy in the range of 97.50–102.10%. The percentage relative standard deviation (% RSD) for six replicates said to be injections were less than 10%. Conclusion The proposed method was validated successfully as per ICH guidelines. Hence, this is employed for the determination of phenyl vinyl sulfone in the eletriptan hydrobromide.

scholarly journals A highly sensitive octopus-like azobenzene fluorescent probe for determination of abamectin B1 in apples

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Zhenlong Guo ◽  
YiFei Su ◽  
Kexin Li ◽  
MengYi Tang ◽  
Qiang Li ◽  
...  
Keyword(s):  
Fluorescent Probe ◽  
Limit Of Detection ◽  
Quantitative Detection ◽  
Fluorescence Signal ◽  
Ionization Mass ◽  
Limit Of Quantification ◽  
Visible Absorption ◽  
Esi Ms ◽  
Relative Standard ◽  
Ft Ir

AbstractThe development of detecting residual level of abamectin B1 in apples is of great importance to public health. Herein, we synthesized a octopus-like azobenzene fluorescent probe 1,3,5-tris (5′-[(E)-(p-phenoxyazo) diazenyl)] benzene-1,3-dicarboxylic acid) benzene (TPB) for preliminary detection of abamectin B1 in apples. The TPB molecule has been characterized by ultraviolet–visible absorption spectrometry, 1H-nuclear magnetic resonance, fourier-transform infrared (FT-IR), electrospray ionization mass spectroscopy (ESI-MS) and fluorescent spectra. A proper determination condition was optimized, with limit of detection and limit of quantification of 1.3 µg L−1 and 4.4 μg L−1, respectively. The mechanism of this probe to identify abamectin B1 was illustrated in terms of undergoing aromatic nucleophilic substitution, by comparing fluorescence changes, FT-IR and ESI-MS. Furthermore, a facile quantitative detection of the residual abamectin B1 in apples was achieved. Good reproducibility was present based on relative standard deviation of 2.2%. Six carboxyl recognition sites, three azo groups and unique fluorescence signal towards abamectin B1 of this fluorescent probe demonstrated reasonable sensitivity, specificity and selectivity. The results indicate that the octopus-like azobenzene fluorescent probe can be expected to be reliable for evaluating abamectin B1 in agricultural foods.

scholarly journals Determination of 77 Multiclass Pesticides and Their Metabolitesin Capsicum and Tomato Using GC-MS/MS and LC-MS/MS

Molecules ◽  
2021 ◽  
Vol 26 (7) ◽  
pp. 1837
Author(s):  
Harischandra Naik Rathod ◽  
Bheemanna Mallappa ◽  
Pallavi Malenahalli Sidramappa ◽  
Chandra Sekhara Reddy Vennapusa ◽  
Pavankumar Kamin ◽  
...  
Keyword(s):  
Limit Of Detection ◽  
Solid Phase ◽  
Graphitized Carbon Black ◽  
Limit Of Quantification ◽  
Gas And Liquid Chromatography ◽  
Relative Standard ◽  
The Matrix ◽  
Liquid Chromatography Tandem Mass ◽  
Primary Secondary Amine

A quick, sensitive, and reproducible analytical method for the determination of 77 multiclass pesticides and their metabolites in Capsicum and tomato by gas and liquid chromatography tandem mass spectrometry was standardized and validated. The limit of detection of 0.19 to 10.91 and limit of quantification of 0.63 to 36.34 µg·kg−1 for Capsicum and 0.10 to 9.55 µg·kg−1 (LOD) and 0.35 to 33.43 µg·kg−1 (LOQ) for tomato. The method involves extraction of sample with acetonitrile, purification by dispersive solid phase extraction using primary secondary amine and graphitized carbon black. The recoveries of all pesticides were in the range of 75 to 110% with a relative standard deviation of less than 20%. Similarly, the method precision was evaluated interms of repeatability (RSDr) and reproducibility (RSDwR) by spiking of mixed pesticides standards at 100 µg·kg−1 recorded anRSD of less than 20%. The matrix effect was acceptable and no significant variation was observed in both the matrices except for few pesticides. The estimated measurement uncertainty found acceptable for all the pesticides. This method found suitable for analysis of vegetable samples drawn from market and farm gates.

scholarly journals Determination of uric acid in human serum by an enzymatic method using N-methyl-N-(4-aminophenyl)-3-methoxyaniline reagent

2003 ◽  
Vol 68 (8-9) ◽  
pp. 691-698 ◽  
Author(s):  
Milena Jelikic-Stankov ◽  
Predrag Djurdjevic ◽  
Dejan Stankov
Keyword(s):  
Uric Acid ◽  
Human Serum ◽  
Limit Of Detection ◽  
Ascorbate Oxidase ◽  
Acid Oxidation ◽  
Uric Acid Concentration ◽  
Enzymatic Method ◽  
Limit Of Quantification ◽  
Relative Standard

In this work a new enzymatic method for the determination of uric acid in human serum has been developed. The method is based on the oxidative coupling reaction between the N-methyl-N-(4-aminophenyl)-3-methoxyaniline (NCP) reagent and the hydrogen ? donor reagent N-ethyl-N-(2-hydroxy-3-sulfopropyl)-3-methylaniline (TOOS), in the system involving three enzymes: uricase, peroxidase and ascorbate oxidase. Using this method uric acid could be determined in concentrations up to 1.428 mmol/L, with a relative standard deviation of up to 1.8 %. The effect of the medium pH and the NCP concentration on the linearity of the chromogen absorbance versus the uric acid concentration curve was investigated. The influence of the uricase activity on the maximum rate of uric acid oxidation was also examined. The use of the NCP reagent demonstrated a more precise and more sensitive determination of the uric acid compared to the determination with 4-aminoantipyrine (4-AA) as the coupling regent. The sensitivity of the method determined from the calibration curve was 0.71 absorbance units per mmol/L of uric acid; the limit of detection was LOD = 0.0035 mmol/L and the limit of quantification was LOQ = 0.015 mmol/L of uric acid.

scholarly journals Application of RP-HPLC for the Estimation of Allopurinol and Its Related Substances in Bulk and Tablet Dosage Form

2021 ◽  
pp. 11-20
Author(s):  
Ch. Jaswanth Kumar ◽  
Prachet Pinnamaneni ◽  
Siva Prasad Morla ◽  
K. N. Rajini Kanth ◽  
Rama Rao Nadendla
Keyword(s):  
Drug Testing ◽  
Dosage Form ◽  
Method Development ◽  
Limit Of Detection ◽  
Limit Of Quantification ◽  
Related Substance ◽  
Related Substances ◽  
Rp Hplc ◽  
Relative Standard ◽  
Tablet Dosage

Aims: The main aim of the present study was to develop and validate a simple and cost- effective method for the estimation of allopurinol and its related substances by using RP-HPLC. Study Design:  Estimation of Allopurinol and its related substance in bulk and tablet dosage forms by RP-HPLC. Place and Duration of Study: Chalapathi Drug Testing Laboratory, Chalapathi Institute of Pharmaceutical Sciences, Chalapathi Nagar, Lam, Guntur-522034 between October 2020 to January 2021. Methodology: Method development was carried out by using Schimadzu, Prominence-i series LC 3D-Plus autosampler embedded with lab solutions software, equipped with PDA detector using YMC column (150 mm X 4.6 mm, 3 μm) and 0.1M Ammonium acetate buffer as a mobile phase in the ratio of 100% at a flow rate of 1.0 ml/min at a wavelength of 255nm. The developed method was validated according to ICH guidelines. Results:  The linearity was observed in the range of 20-100 µg/ml with a regression (R2) value of 0.999. Developed method was specific with no interactions and accurate with 100.11% for allopurinol and 99.54% for its related substance. The limit of detection for allopurinol was 2 µg/ml and for related substance was 0.0.1 µg/ml. The limit of quantification for allopurinol was 6 µg/ml and for related substance was 0.03 µg/ml respectively. The percentage relative standard deviation was found to be NMT 2 which indicates that the proposed method was precise and robust. Conclusion:  The developed method was simple, precise and accurate and can be successfully employed for the estimation of allopurinol in bulk and tablet dosage form.

Sign in / Sign up

Export Citation Format

Share Document