scholarly journals A New Cutting Device Design to Study the Orthogonal Cutting of CFRP Laminates at Different Cutting Speeds

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4074 ◽  
Author(s):  
Víctor Criado ◽  
Norberto Feito ◽  
José Luis Cantero Guisández ◽  
José Díaz-Álvarez
Keyword(s):  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Linear Displacement ◽  
Tool Geometry ◽  
Cfrp Laminates ◽  
Reinforced Plastics ◽  
Wide Range ◽  
Cutting Speeds

Carbon Fiber-reinforced plastics (CFRPs) are widely used in the aerospace industry due to their highly mechanical properties and low density. Most of these materials are used in high-risk structures, where the damage caused by machining must be controlled and minimized. The optimization of these processes is still a challenge in the industry. In this work, a special cutting device, which allows for orthogonal cutting tests, with a linear displacement at a wide range of constant cutting speeds, has been developed by the authors. This paper describes the developed cutting device and its application to analyze the influence of tool geometry and cutting parameters on the material damage caused by the orthogonal cutting of a thick multidirectional CFRP laminate. The results show that a more robust geometry (higher cutting edge radius and lower rake angle) and higher feed cause an increase in the thrust force of a cutting tool, causing burrs and delamination damage. By reducing the cutting speed, the components with a higher machining force were also observed to have less surface integrity control.

Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites

2013 ◽  
Author(s):  
Felicia Stan ◽  
Daniel Vlad ◽  
Catalin Fetecau
Keyword(s):  
Friction Coefficient ◽  
Cutting Force ◽  
Feed Rate ◽  
Normal Force ◽  
Polynomial Regression ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Force Model

This paper presents an experimental investigation of the cutting forces response during the orthogonal cutting of polytetrafluoroethylene (PTFE) and PTFE-based composites using the Taguchi method. Cutting experiments were conducted using the L27 orthogonal array and the effects of the cutting parameters (feed rate, cutting speed and rake angle) on the cutting force were analyzed using the S/N ratio response and the analysis of variance (ANOVA). Statistical models that correlate the cutting force with process variables were developed using ANOVA and polynomial regression. The variation of the apparent friction coefficient was analyzed with respect to tool geometry and the cutting process. The results indicated that cutting and thrust forces increase with increasing feed rate, and decrease with increasing rake angles from negative to positive values and increasing cutting speed. A power law relationship between the apparent friction coefficient and the normal force exerted by the chip on the tool-rake face was identified, the former decreasing with an increasing normal force.

FEA Simulation of the Influence of Cutting Parameters on Serrated Chip Formation in Machining Titanium Alloy Ti-6Al-4V

2012 ◽  
Vol 500 ◽  
pp. 152-156
Author(s):  
Zeng Hui Jiang ◽  
Ji Lu Feng ◽  
Xiao Ye Deng
Keyword(s):  
Titanium Alloy ◽  
Chip Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Element Model ◽  
Serrated Chip ◽  
Wide Range ◽  
Serrated Chip Formation ◽  
Fea Simulation

A finite element model of a two dimensional orthogonal cutting process is developed. The simulation uses standard finite software is able to solve complex thermo-mechanical problems. A thermo-visco-plastic model for the machined material and a rigid cutting tool were assumed. One of the main characteristic of titanium alloy is serrated shape for a wide range of cutting conditions. In order to understand the influence of cutting parameters on the chip formation when machining titanium alloy Ti-6Al-4V. The influence of the cutting speed,the cutting depth and the feed on the chip shape giving rise to segmented chips by strain localisation is respectively discussed.

Mechanism of Chip Deformation in Orthogonal Cutting the Wheel Steel

2008 ◽  
Vol 375-376 ◽  
pp. 26-30
Author(s):  
Kai Xue ◽  
Xiang Ming Xu ◽  
Gang Liu ◽  
Ming Chen
Keyword(s):  
Chip Formation ◽  
Feed Rate ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Chip Morphology ◽  
Cutting Parameters ◽  
Wheel Steel ◽  
Tool Geometry ◽  
Orthogonal Turning ◽  
On Chip

The chip formation and morphology are definitely affected by tool geometry and cutting parameters such as cutting speed, feed rate, and depth of cutting. An experiment investigation was presented to study the influence of tool geometry on chip morphology, and to clarify the effect of different cutting parameters on chip deformation in orthogonal turning the wheel steel. The result obtained in this study showed that tool geometry affected the chip morphology significantly; cutting speed was the most contributive factor in forming saw-tooth chip.

Built-Up-Edge Formation in Micromilling

2015 ◽  
Author(s):  
V. Kovvuri ◽  
Z. Wang ◽  
A. Araujo ◽  
M. B. da Silva ◽  
S. Bukkapatnam ◽  
...  
Keyword(s):  
Surface Finish ◽  
Cutting Speed ◽  
Minimum Quantity Lubrication ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Machined Surface ◽  
Area Density ◽  
Milled Surface ◽  
Chip Load ◽  
Cutting Speeds

This paper presents experimental study on conditions for built-up-edge (BUE) formation and its effects in micromilling. Surface finish and BUE area density on a micromilled surface are used to quantify the presence of BUE. A model for surface finish is derived based on the topography of milled surface and tool geometry. Assuming no BUE formation, this empirical model shows the dependence of surface finish on chip load, tool concavity angle, and includes the effect of cutting parameters and milling modes (up-milling or down-milling). Micromilling tools of 100–400 μm diameters are used for milling stainless steel at 10–60 m/min cutting speed, 0.05–1 μm/flute chip load, in minimum quality lubrication condition (MQL). A BUE, embedded onto either a milled surface or tool cutting edge or chip, is identified by scanning electron microscopy and energy dispersive spectroscopy techniques; the severity of BUE formation is quantified as area density when observing a machined surface at high magnification with optical microscopy or interferometry. Condition for BUE formation is presented by mapping the surface finish and BUE area density against cutting speed and chip load. A microtool would fracture catastrophically at high cutting speeds and/or high chip loads due to excessive dynamic stresses on a microtool; such tool would also fail at the other extreme when low cutting speeds and chip loads promote formation and detachment of BUE on the tool surface, therefore, chipping the fragile microcutting edges of a microtool. There is an optimal zone for effective micromilling without tool failure and BUEs. The measured surface finish approaches the theoretical value when BUE is absent, i.e. micromilling in minimum quantity lubrication at cutting speed between 40–60 m/min and chip load higher than 0.15μm/tooth. The BUE area density for up-milling is lower than that for down-milling at low cutting speed; such difference gradually diminishes when selecting milling parameters in the optimal zone where BUE is practically absent.

Surface Morphology in Milling Multidirectional Carbon Fiber Reinforced Polymer Laminates

2013 ◽  
Vol 683 ◽  
pp. 158-162 ◽  
Author(s):  
You Hong Gong ◽  
Ni Hong Yang ◽  
Shu Han ◽  
Yan Chen ◽  
Yu Can Fu ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Surface Morphology ◽  
Matrix Material ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Feed Speed ◽  
Fiber Reinforced ◽  
Cfrp Laminates ◽  
Reinforced Plastics ◽  
Carbon Fiber Reinforced

Carbon fiber reinforced plastics (CFRP) use in many industries applications has seen a dramatic increase over the last decade. Milling is the most practical machining operation for removing excess material. The work presented details the effect of different cutting parameters on the surface roughness and integrity of machined multidirectional CFRP laminates. The results indicate that the surface morphology mainly relates to the fiber orientation. Increasing cutting speed leads to severe softening, degradation and burning of the matrix material that binds fibers together. The feed speed has little effect on the surface morphology. And the roughness value Ra increases with the feed rate, and decreases with the cutting speed.

Cutting Tool Geometry and Parameters Effects on the Force and Temperature in Turning Steel 1040 Using Finite Element Analysis

2012 ◽  
Vol 548 ◽  
pp. 465-470
Author(s):  
Asaad A. Abdullah ◽  
Usama J. Naeem ◽  
Cai Hua Xiong
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Cutting Forces ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Heat Rate ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Tool Geometry ◽  
Element Analysis

In recent years, applications have been proven finite-element method (FEM) in metal-cutting operations to be effective process in the study of cutting and chip formation. In this study, the simulation results are useful for both researchers and machine tool manufacturers for improving the design of cutting parameters. Finite-element analysis (FEA) that used in this study of simulation the cutting parameters and tool geometries effects on the force and temperature in turning AISI 1040. The simulation parameters that used in this study are cutting speed (75 - 300 m/min),feed rate (0.2 mm/rev), cut depth (0.75-1.5 mm), and rake angle (0-20 °). The results of cutting forces were (240 – 520 N), the temperature were (300-420 °C), and the heat rate (14202.3-83772.8 W/mm3) on the cutting edge. The simulation process also show that the increase of cutting speed leads to decrease in the cutting forces, while it has increasing in temperature, and heat rate. Also, the results show that the increase of cutting depth associated increase the cutting force only.

Finite Element Simulation of Cutting Forces in Orthogonal Machining of Titanium Alloy Ti-6Al-4V

2014 ◽  
Vol 474 ◽  
pp. 192-199 ◽  
Author(s):  
Ladislav Kandráč ◽  
Ildikó Maňková ◽  
Marek Vrabel' ◽  
Jozef Beňo
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Cutting Forces ◽  
Orthogonal Cutting ◽  
Experimental Studies ◽  
Cutting Speed ◽  
Rake Angle ◽  
Simulation Software ◽  
Tool Geometry ◽  
Element Method

In this paper, a Lagrangian finite element-based machining model is applied in the simulation of cutting forces in two-dimensional orthogonal cutting of titanium Ti-6Al-4V alloy. The simulations were conducted using 2D Finite Element Method (FEM) machining simulation software. In addition, the cutting experiments were carried out under the different cutting speed, feed and tool geometry (rake angle, clearance angle and cutting edge radius). The effect of cutting speed, feed and tool geometry on cutting force were investigated. The results obtained from the finite element method (FEM) and experimental studies were compared.

scholarly journals Effect of Cutting Parameters on Cutting Temperature of TiAl6V4 Alloy

2013 ◽  
Vol 392 ◽  
pp. 68-72 ◽  
Author(s):  
S. Sulaiman ◽  
A. Roshan ◽  
S. Borazjani
Keyword(s):  
Feed Rate ◽  
Rate Increase ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Material Model ◽  
Rake Angle ◽  
Coulomb’S Friction ◽  
Abaqus Software

A Finite Element Modeling (FEM) and Simulation was Used to Investigate the Effect of Tool Rake Angle, Cutting Speed and Feed Rate on the Cutting Temperature of Tial6v4 Alloy. the Purpose of this Study was to Find Proper Cutting Parameters for Machining of Titanium Alloy where Cutting Temperature was Lowest. A FEM Based on ABAQUS Software which Involves Jonson-Cook Material Model and Coulomb’s Friction Law was Applied to Simulate an Orthogonal Cutting Process. in this Simulation Work, a Range of Tool Rake Angle from 0° to 10°, a Range of Cutting Speed from 300 m/min to 600 m/min and a Range of Feed Rate between 0.1 Rev/mm and 0.25 Rev/mm were Investigated. the Simulation Results Indicated that Increase in Rake Angle Reduces Cutting Temperature while Increasing Cutting Speed and Feed Rate Increase the Cutting Temperature.

An Experimental Study of High Speed Orthogonal Cutting

1998 ◽  
Vol 120 (1) ◽  
pp. 169-172 ◽  
Author(s):  
G. Sutter ◽  
A. Molinari ◽  
L. Faure ◽  
J. R. Klepaczko ◽  
D. Dudzinski
Keyword(s):  
Experimental Study ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
High Speed Machining ◽  
Workpiece Material ◽  
Wide Range ◽  
Longitudinal Cutting ◽  
Material Interaction ◽  
Cutting Speeds

A new high speed machining experiment is designed to obtain orthogonal cutting in a wide range of cutting speeds from 7 m/s to 100 m/s. Quasi-stationary cutting conditions are obtained. The measurement of the longitudinal cutting force reveals the existence of an optimal cutting speed for which the energy consumption is minimum. The genuine tool-workpiece material interaction can be analyzed with that experimental device.

An Experimental Study of Orthogonal Cutting of SiCp/Al Composites: Cutting Forces Analysis

2012 ◽  
Vol 500 ◽  
pp. 230-235
Author(s):  
Shu Tao Huang ◽  
Li Zhou ◽  
Jin Lei Wang
Keyword(s):  
Cutting Force ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Rake Angle ◽  
Mechanical And Thermal Properties ◽  
Cutting Depth ◽  
Metal Parts ◽  
Orthogonal Machining ◽  
Rapid Tool

Due to the superior mechanical and thermal properties of SiCp/Al composites, their poor machinability has been the main deterrent to their substitution for metal parts. Machining of SiCp/Al composites has been considerably difficult because the extremely abrasive nature of SiC reinforcements causes rapid tool wear. In this paper, an experiment was carried out to investigate the influence of the cutting speed, cutting depth and tool rake angle on cutting force during orthogonal machining of SiCp/Al composites. The results indicate that the cutting depth is one of the main cutting parameters that affect the cutting force, while the cutting speed and tool rake angle have no significant effects on the cutting force.

Sign in / Sign up

Export Citation Format

Share Document