scholarly journals Mechanical Properties of High-Strength Cu–Cr–Zr Alloy Fabricated by Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5028
Author(s):  
Fujia Sun ◽  
Ping Liu ◽  
Xiaohong Chen ◽  
Honglei Zhou ◽  
Pengfei Guan ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
High Efficiency ◽  
High Strength ◽  
Scanning Speed ◽  
Laser Melting ◽  
Ansys Simulation ◽  
Zr Alloy

The approximate process range for preparing the Cu–Cr–Zr alloy by selective laser melting (SLM) was determined by ANSYS simulation, and the influence of the SLM process parameters on the comprehensive properties of the SLM-formed alloy was studied by the design of experiments. The Cu–Cr–Zr alloy with optimum strength and hardness was prepared with high efficiency by optimizing the process parameters for SLM (i.e., laser power, scanning speed, and hatching distance). It is experimentally shown that tensile strength and hardness of the SLM alloy are increased by increasing laser power and decreasing scanning speed, whereas they are initially increased and then decreased by increasing the hatching distance. Moreover, strength, roughness and hardness of the SLM alloy are optimized when laser power is 460 W, scanning speed is 700 mm/s and hatching distance is 0.06 mm. The optimized properties of the SLM alloy are a tensile strength of 153.5 MPa, hardness of 119 HV, roughness of 31.384 μm and relative density of 91.62%.

scholarly journals Numerical Simulation of Moving Heat Flux during Selective Laser Melting of AlSi25 Alloy Powder

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 877
Author(s):  
Cong Ma ◽  
Xianshun Wei ◽  
Biao Yan ◽  
Pengfei Yan
Keyword(s):  
Numerical Simulation ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Molten Pool ◽  
Laser Power ◽  
Scanning Speed ◽  
Powder Layer ◽  
Maximum Temperature ◽  
Three Dimensional Model ◽  
Laser Melting

A single-layer three-dimensional model was created to simulate multi-channel scanning of AlSi25 powder in selective laser melting (SLM) by the finite element method. Thermal behaviors of laser power and scanning speed in the procedure of SLM AlSi25 powder were studied. With the increase of laser power, the maximum temperature, size and cooling rate of the molten pool increase, while the scanning speed decreases. For an expected SLM process, a perfect molten pool can be generated using process parameters of laser power of 180 W and a scanning speed of 200 mm/s. The pool is greater than the width of the scanning interval, the depth of the molten pool is close to scan powder layer thickness, the temperature of the molten pool is higher than the melting point temperature of the powder and the parameters of the width and depth are the highest. To confirm the accuracy of the simulation results of forecasting excellent process parameters, the SLM experiment of forming AlSi25 powder was carried out. The surface morphology of the printed sample is intact without holes and defects, and a satisfactory metallurgical bond between adjacent scanning channels and adjacent scanning layers was achieved. Therefore, the development of numerical simulation in this paper provides an effective method to obtain the best process parameters, which can be used as a choice to further improve SLM process parameters. In the future, metallographic technology can also be implemented to obtain the width-to-depth ratio of the SLM sample molten pool, enhancing the connection between experiment and theory.

scholarly journals Selective Laser Melting of Pre-Alloyed NiTi Powder: Single-Track Study and FE Modeling with Heat Source Calibration

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7486
Author(s):  
Stanislav V. Chernyshikhin ◽  
Denis G. Firsov ◽  
Igor V. Shishkovsky
Keyword(s):  
Heat Source ◽  
Thermal Behavior ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
Scanning Speed ◽  
Fe Modeling ◽  
Single Track ◽  
Laser Melting ◽  
Melt Pool

Unique functional properties such as the low stiffness, superelasticity, and biocompatibility of nickel–titanium shape-memory alloys provide many applications for such materials. Selective laser melting of NiTi enables low-cost customization of devices and the manufacturing of highly complex geometries without subsequent machining. However, the technology requires optimization of process parameters in order to guarantee high mass density and to avoid deterioration of functional properties. In this work, the melt pool geometry, surface morphology, formation mode, and thermal behavior were studied. Multiple combinations of laser power and scanning speed were used for single-track preparation from pre-alloyed NiTi powder on a nitinol substrate. The experimental results show the influence of laser power and scanning speed on the depth, width, and depth-to-width aspect ratio. Additionally, a transient 3D FE model was employed to predict thermal behavior in the melt pool for different regimes. In this paper, the coefficients for a volumetric double-ellipsoid heat source were calibrated with bound optimization by a quadratic approximation algorithm, the design of experiments technique, and experimentally obtained data. The results of the simulation reveal the necessary conditions of transition from conduction to keyhole mode welding. Finally, by combining experimental and FE modeling results, the optimal SLM process parameters were evaluated as P = 77 W, V = 400 mm/s, h = 70 μm, and t = 50 μm, without printing of 3D samples.

scholarly journals Achieving Ti-5Al-4Sn-2Zr-1Mo-0.25Si-1Nb Alloys with High Strength and Moderate Ductility through Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (23) ◽  
pp. 5527
Author(s):  
Jiangtao Ran ◽  
Xiaojing Sun ◽  
Shiliang Wei ◽  
Zhuo Chen ◽  
Hong Zhao
Keyword(s):  
Tensile Strength ◽  
Titanium Alloy ◽  
Selective Laser Melting ◽  
Laser Power ◽  
High Strength ◽  
Composition Analysis ◽  
Laser Melting ◽  
Energy Dispersion Spectrum ◽  
Average Grain Size ◽  
Cruise Missiles

Ti-5Al-4Sn-2Zr-1Mo-0.25Si-1Nb (TA32) titanium alloy is a kind of near α high temperature titanium alloy with great application prospects in aero-engine afterburners and cruise missiles. However, there are still few studies on the microstructure and mechanical properties of TA32 specimens produced by selective laser melting (SLM) technology. In this study, TA32 specimens with high strength (tensile strength of 1267 MPa) and moderate ductility (elongation after fracture of 8%) were obtained by selective laser melting. The effect of laser power on the microstructure and mechanical behavior was studied and the results demonstrated that the average grain size increases with increasing laser power from 200 W to 400 W. Micro-zone composition analysis was carried out by energy dispersion spectrum (EDS), showing that the Al concentration inner grains is higher than that near grain boundaries. Fracture analysis results demonstrated that the fracture mode of SLM TA32 specimens was cleavage fracture. The tensile strength of the specimens built with a laser power of 250 W at 500 °C, 550 °C and 600 °C was measured as 869 MPa, 819 MPa and 712 MPa, respectively.

scholarly journals The Influence of Selective Laser Melting Process Parameters on the Property of TiAlN/TiN Multilayer Coating on the 316L Steel

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 377 ◽  
Author(s):  
Yueling Lyu ◽  
Jingwei Wang ◽  
Yulin Wan ◽  
Yangzhi Chen
Keyword(s):  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
Orthogonal Experiment ◽  
Multilayer Coating ◽  
Melting Process ◽  
Scanning Speed ◽  
Laser Melting ◽  
Wear Rates ◽  
Comprehensive Property

Selective laser melting (SLM) is an important advanced additive manufacturing technology. The existing SLM products cannot fully meet the requirements of high-precision and strength of the mechanical component because of their defects. The TiAlN/TiN multilayer coating can improve the surface property of SLM products. The present work aims to explore the influences of different process parameters of SLM on the property of TiAlN/TiN multilayer coating plating on the 361L specimen and the mechanism of these influences. Taking laser power, scanning speed, and scanning space as factors, an orthogonal experiment was designed. The TiAlN/TiN multilayer coating specimens can be obtained by plating on the 361L specimen, fabricated by the process parameters of SLM on the orthogonal experiment. The surface topographies and properties of TiAlN/TiN multilayer coating were tested, the influences of SLM process parameters on TiAlN/TiN multilayer coating were analyzed, and the optimal process parameter was obtained. The electron microscope images revealed that the surface morphology of TiAlN/TiN multilayer coating plating on the SLM specimen was relatively flat, and there were some macro-particles in different sizes and pin holes dispersed on it. The thickness of the TiAlN/TiN multilayer coating was 2.77–3.29 μm. The microhardness value of coating SLM specimen was more than four times that of the uncoated SLM specimen and the wear rates of the uncoated specimen were 2–4 times that of the corresponding coating specimen. The comprehensive analysis shows that the laser power had the greatest influence on the comprehensive property of the coating. The primary cause of the influence of SLM process parameters on the properties of the TiAlN/TiN multilayer coating was preliminarily discussed. When the laser power was 170 W, the scanning speed was 1,100 mm/s, and the scanning space was 0.08mm, the TiAlN/TiN multilayer coating plating on the SLM specimen had the best comprehensive property.

Fabrication of high-strength Mg-Gd-Zn-Zr alloy via selective laser melting

2020 ◽  
Vol 165 ◽  
pp. 110377 ◽  
Author(s):  
Qingchen Deng ◽  
Yujuan Wu ◽  
Yuanhang Luo ◽  
Ning Su ◽  
Xiaoyu Xue ◽  
...  
Keyword(s):  
Selective Laser Melting ◽  
High Strength ◽  
Laser Melting ◽  
Zr Alloy

Influence of Selective Laser Melting Process Parameters on Densification Behavior, Surface Quality and Hardness of 18Ni300 Steel

2020 ◽  
Vol 861 ◽  
pp. 77-82
Author(s):  
Gan Li ◽  
Cheng Guo ◽  
Wen Feng Guo ◽  
Hong Xing Lu ◽  
Lin Ju Wen ◽  
...  
Keyword(s):  
Energy Density ◽  
Relative Density ◽  
Maraging Steel ◽  
Surface Quality ◽  
Selective Laser Melting ◽  
Process Parameters ◽  
Laser Power ◽  
Densification Behavior ◽  
Laser Melting ◽  
Scan Speed

This study investigated the effect of laser power (P), scan speed (v) and hatch space (h) on densification behavior, surface quality and hardness of 18Ni300 maraging steel fabricated by selective laser melting (SLM). The results indicated that the relative density of the SLMed samples has a shape increase from 73% to 97% with the laser energy density increasing from 0.5 to 2.2 J/mm2. The relative density ≥ 99% was achieved at the energy density in the range of 2.2~5.9 J/mm2. The optimum process parameters were found to be laser power of 150~200 W, scan speed of 600mm/s and hatch space of 0.105mm. In addition, it was found that the hardness increased initially with the increasing relative density up to relative density of 90% and then little relationship, but finally increase again significantly. This work provides reference for determining process parameters for SLMed maraging steel and the development of 3D printing of die steels.

Evaluation of Physicomechanical Properties of Ti-45Nb Specimens Obtained by Selective Laser Melting

2017 ◽  
Vol 743 ◽  
pp. 9-12
Author(s):  
Zhanna G. Kovalevskaya ◽  
Margarita A. Khimich ◽  
Andrey V. Belyakov
Keyword(s):  
Young’S Modulus ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Young's Modulus ◽  
Scanning Speed ◽  
Physicomechanical Properties ◽  
Optical Methods ◽  
Laser Melting ◽  
Average Value ◽  
Hardness Tester

Porosity, values of nanohardness and Young’s modulus of the specimens obtained with the method of selective laser melting were measured with optical methods, scanning electron microscopy and Nano Hardness Tester NHT-S-AX-000X device for measuring physicomechanical properties. Ti-45wt%Nb powder obtained with mechanical alloying was used for selective laser melting. The results have shown that increased heat input due to the laser power growth up to 80 W and scanning speed decrease down to 40 mm/s decreases the porosity of the specimen. The nanohardness average value is not sensitive to the changes of scanning modes in the investigated range. The Young’s modulus decreases with energy input increase.

scholarly journals Collaborative Optimization on Density and Surface Roughness of 316L Stainless Steel in Selective Laser Melting

2020 ◽  
Author(s):  
Yong Deng ◽  
Zhongfa Mao ◽  
Nan Yang ◽  
Xiaodong Niu ◽  
Xiangdong Lu
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Relative Density ◽  
Selective Laser Melting ◽  
Laser Power ◽  
316L Stainless Steel ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Collaborative Optimization ◽  
Laser Melting

Although the concept of additive manufacturing has been proposed for several decades, momentum of selective laser melting (SLM) is finally starting to build. In SLM, density and surface roughness, as the important quality indexes of SLMed parts, are dependent on the processing parameters. However, there are few studies on their collaborative optimization in SLM to obtain high relative density and low surface roughness simultaneously in the previous literature. In this work, the response surface method was adopted to study the influences of different processing parameters (laser power, scanning speed and hatch space) on density and surface roughness of 316L stainless steel parts fabricated by SLM. The statistical relationship model between processing parameters and manufacturing quality is established. A multi-objective collaborative optimization strategy considering both density and surface roughness is proposed. The experimental results show that the main effects of processing parameters on the density and surface roughness are similar. It is noted that the effects of the laser power and scanning speed on the above objective quality show highly significant, while hatch space behaves an insignificant impact. Based on the above optimization, 316L stainless steel parts with excellent surface roughness and relative density can be obtained by SLM with optimized processing parameters.

Effect of processing parameters on forming defects during selective laser melting of AlSi10Mg powder

2020 ◽  
Vol 26 (5) ◽  
pp. 871-879 ◽  
Author(s):  
Haihua Wu ◽  
Junfeng Li ◽  
Zhengying Wei ◽  
Pei Wei
Keyword(s):  
Selective Laser Melting ◽  
Laser Power ◽  
Scanning Speed ◽  
Processing Parameters ◽  
Argon Pressure ◽  
Powder Layer ◽  
Laser Melting ◽  
Content Type ◽  
Scan Speed ◽  
Forming Defects

Purpose To fabricate a selective laser melting (SLM)-processed AlSi10Mg part with almost full density and free of any apparent pores, this study aims to investigate the effect of ambient argon pressure and laser scanning speed on the particles splash during the AlSi10Mg powder bed laser melting. Design/methodology/approach Based on the discrete element method (DEM), a 3D model of random distribution of powder particles was established, and the 3D free surface of SLM forming process was dynamically tracked by the volume of fluid, where a Gaussian laser beam acts as the energy source melting the powder bed. Through the numerical simulation and process experimental research, the effect of the applied laser power and scanning speed on the operating laser melting temperature was studied. Findings The process stability has a fundamental role in the porosity formation, which is process-dependent. The effect of the processing conditions on the process stability and the resultant forming defects were clarified. Research limitations/implications The results shows that the pores were the main defects present in the SLM-processed AlSi10Mg sample, which decreases the densification level of the sample. Practical implications The optimal processing parameters (argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm ) applied during laser melting can improve the quality of selective laser melting of AlSi10Mg, Social implications It can provide a technological support for 3D printing. Originality/value Based on the analysis of the pore and balling formation mechanisms, the optimal processing parameters have been obtained, which were argon pressure of 1,000 Pa, laser power of 180 W, scan speed of 1,000 mm/s, powder layer thickness of 35 µm and hatch spacing of 50 µm. Then, a near-fully dense sample free of any apparent pores on the cross-sectional microstructure was produced by SLM, wherein the relative density of the as-built samples is larger than 97.5%.

scholarly journals In Situ Mo(Si,Al)2-Based Composite through Selective Laser Melting of a MoSi2-30 wt.% AlSi10Mg Mixture

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3720 ◽  
Author(s):  
Tatevik Minasyan ◽  
Sofiya Aydinyan ◽  
Ehsan Toyserkani ◽  
Irina Hussainova
Keyword(s):  
High Temperature ◽  
Selective Laser Melting ◽  
Laser Power ◽  
Laser Scanning ◽  
Scanning Speed ◽  
Laser Melting ◽  
Structural Applications ◽  
Laser Scanning Speed ◽  
Fusion Approach

The laser power bed fusion approach has been successfully employed to manufacture Mo(Si,Al)2-based composites through the selective laser melting of a MoSi2-30 wt.% AlSi10Mg mixture for high-temperature structural applications. Composites were manufactured by leveraging the in situ reaction of the components during printing at 150–300 W laser power, 500–1000 mm·s−1 laser scanning speed, and 100–134 J·mm−3 volumetric energy density. Microcomputed tomography scans indicated a negligible induced porosity throughout the specimens. The fully dense Mo(Si1-x,Alx)2-based composites, with hardness exceeding 545 HV1 and low roughness for both the top (horizontal) and side (vertical) surfaces, demonstrated that laser-based additive manufacturing can be exploited to create unique structures containing hexagonal Mo(Si0.67Al0.33)2.

Sign in / Sign up

Export Citation Format

Share Document