scholarly journals Impact of Equal Channel Angular Pressing on Mechanical Behavior and Corrosion Resistance of Hot-Rolled Ti-2Fe-0.1B Alloy

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5117
Author(s):  
Yanhuai Wang ◽  
Xin Li ◽  
I. V. Alexandrov ◽  
Li Ma ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Grain Size ◽  
Corrosion Resistance ◽  
Titanium Alloy ◽  
Mechanical Behavior ◽  
Equal Channel Angular Pressing ◽  
Hot Rolling ◽  
Low Cost ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Hot Rolled

In the present study, the unique bimodal grain size distribution microstructure with the ultrafine substrate and embedded macro grains was fabricated by a traditional hot-rolling process in a novel low-cost Ti-2Fe-0.1B titanium alloy, which possesses a good combination of strength (around 663 MPa) and ductility (around 30%) without any post heat treatment. Meanwhile, the mechanical behavior and corrosion resistance of hot-rolled Ti-2Fe-0.1B alloy after equal channel angular pressing (ECAP) deformation were studied. Results indicated that the average grain size decreased to 0.24 μm after 4 passes ECAP deformation, which led to the enhancement of tensile strength to around 854 MPa and good ductility to around 15%. In addition, corrosion resistance was also improved after ECAP due to the rapid self-repairing and thicker passivation film. Our study revealed that the novel low-cost titanium alloy after hot-rolling and ECAP could be used instead of Ti-6Al-4V in some industrial applications due to similar mechanical behavior and better corrosion resistance.

scholarly journals Experimental and Numerical Investigation of the ECAP Processed Copper: Microstructural Evolution, Crystallographic Texture and Hardness Homogeneity

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 607
Author(s):  
A. I. Alateyah ◽  
Mohamed M. Z. Ahmed ◽  
Yasser Zedan ◽  
H. Abd El-Hafez ◽  
Majed O. Alawad ◽  
...  
Keyword(s):  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Cross Section ◽  
Room Temperature ◽  
Pure Copper ◽  
High Density ◽  
Ecap Processing ◽  
Heterogeneous Distribution ◽  
Angular Pressing ◽  
Average Grain Size

The current study presents a detailed investigation for the equal channel angular pressing of pure copper through two regimes. The first was equal channel angular pressing (ECAP) processing at room temperature and the second was ECAP processing at 200 °C for up to 4-passes of route Bc. The grain structure and texture was investigated using electron back scattering diffraction (EBSD) across the whole sample cross-section and also the hardness and the tensile properties. The microstructure obtained after 1-pass at room temperature revealed finer equiaxed grains of about 3.89 µm down to submicrons with a high density of twin compared to the starting material. Additionally, a notable increase in the low angle grain boundaries (LAGBs) density was observed. This microstructure was found to be homogenous through the sample cross section. Further straining up to 2-passes showed a significant reduction of the average grain size to 2.97 µm with observable heterogeneous distribution of grains size. On the other hand, increasing the strain up to 4-passes enhanced the homogeneity of grain size distribution. The texture after 4-passes resembled the simple shear texture with about 7 times random. Conducting the ECAP processing at 200 °C resulted in a severely deformed microstructure with the highest fraction of submicron grains and high density of substructures was also observed. ECAP processing through 4-passes at room temperature experienced a significant increase in both hardness and tensile strength up to 180% and 124%, respectively.

Microstructures and Mechanical Properties of AZ61 Mg Alloy Processed by Equal Channel Angular Pressing

2012 ◽  
Vol 468-471 ◽  
pp. 2124-2127 ◽  
Author(s):  
Shao Feng Zeng ◽  
Kai Huai Yang ◽  
Wen Zhe Chen
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Uniform Elongation ◽  
Considerable Decrease ◽  
Angular Pressing ◽  
Az61 Magnesium Alloy ◽  
Average Grain Size ◽  
Microstructures And Mechanical Properties ◽  
Bimodal Grain Size

Equal channel angular pressing (ECAP) was applied to a commercial AZ61 magnesium alloy for up to 8 passes at temperatures as low as 473K. Microstructures and mechanical properties of as-received and ECAP deformed samples were investigated. The microstructure was initially not uniform with a “bimodal” grain size distribution but became increasingly homogeneous with further ECAP passes and the average grain size was considerably reduced from over 26 μm to below 5 μm. The ultimate tensile strength (UTS) decreases clearly after one pass, but increases significantly up to two passes, and then continuously slowly decreases up to six passes, and again increases slightly up to eight passes. In contrast, the uniform elongation increased significantly up to 3 passes, followed by considerable decrease up to 8 passes. These observations may be attributed to combined effects of grain refinement and texture development.

Grain Refinement of Copper Alloys by Equal Channel Angular Pressing

2004 ◽  
Vol 449-452 ◽  
pp. 177-180 ◽  
Author(s):  
Cha Yong Lim ◽  
Jae Hyuck Jung ◽  
Seung Zeon Han
Keyword(s):  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Copper Alloys ◽  
Metallic Materials ◽  
Fine Grained ◽  
Angular Pressing ◽  
Fine Grain ◽  
Transmission Electron ◽  
Ultrafine Grained ◽  
Average Grain Size

The equal channel angular pressing (ECAP) is one of the methods to refine the grain size of metallic materials. This study investigates the effect of ECAP process on the formation of the fine grain size in oxygen free Cu and Cu alloys. The average grain size has been refined from 150 µm before ECAP to 300 nm. Microstructure was analyzed by transmission electron micrography (TEM). The diffraction pattern of the selected area confirmed the formation of ultrafine-grained structure with high angle grain boundaries after 8 cycles of ECAP. Mechanical properties such as microhardness and tensile properties of the ultra-fine grained copper materials have been investigated.

Microstructure and Mechanical Properties of Mg96Y3Zn1 Alloy Processed by Equal Channel Angular Pressing

2011 ◽  
Vol 682 ◽  
pp. 49-54
Author(s):  
Bin Chen ◽  
Chen Lu ◽  
Dong Liang Lin ◽  
Xiao Qin Zeng
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Equal Channel Angular Pressing ◽  
Ultrafine Grains ◽  
Angular Pressing ◽  
Average Grain Size

The Mg96Y3Zn1 alloy processed by equal channel angular pressing has been investigated. It was found that the Mg96Y3Zn1 alloy processed by ECAP obtained ultrafine grains and exhibits excellent mechanical properties. After ECAP, the average grain size of Mg96Y3Zn1 alloy refined to about 400 nm. The highest strengths with yield strength of 381.45MPa and ultimate tensile strength of 438.33MPa were obtained after 2 passes at 623K. It was found that cracks were preferentially initiated and propagated in the interior of X-phase during the tensile test. As a result, the elongation of alloy is decreased with pass number increasing.

Microstructure and Tensile Properties of a Mg-Zn-Y-Zr Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing

2007 ◽  
Vol 353-358 ◽  
pp. 595-598 ◽  
Author(s):  
Shi Wei Xu ◽  
Ming Yi Zheng ◽  
Xiao Guang Qiao ◽  
Wei Min Gan ◽  
Kun Wu ◽  
...  
Keyword(s):  
Grain Size ◽  
Tensile Strength ◽  
Equal Channel Angular Pressing ◽  
Ecap Processing ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Texture Modification ◽  
The Matrix ◽  
Elongation To Failure ◽  
Zr Alloy

Equal channel angular pressing (ECAP) was performed on extruded Mg-Zn-Y-Zr (Mg-5.0wt%Zn-0.9wt%Y-0.2wt%Zr) alloy at 300 oC. After 8 ECAP passes, average grain size of the alloy was reduced to about 1.4 μm, and the quasicrystalline phases were broken and dispersed in the matrix. In addition, nano- quasicrystallines were precipitated from the matrix during ECAP processing. After ECAP, the elongation to failure of the extruded material was significantly improved. Only after 2 ECAP passes, the elongation to failure was 29%, and after 8 ECAP passes, it reached 35%, which was three times larger than that of the as-extruded alloy. However, both yield strength and ultimate tensile strength were decreased with the increasing ECAP passes, which was considered to be resulted from the {0002} basal plane texture modification during ECAP.

Effect of Hot Rolling and Equal-Channel Angular Pressing on Generation of Globular Microstructure in Semi-Solid Mg-3%Zn Alloy

2014 ◽  
Vol 217-218 ◽  
pp. 381-388 ◽  
Author(s):  
Łukasz Rogal ◽  
Frank Czerwiński ◽  
Lidia Litynska-Dobrzyńska ◽  
Piotr Bobrowski ◽  
Anna Wierzbica-Miernik ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Hot Rolling ◽  
Cast Alloy ◽  
Single Step ◽  
Deformation Bands ◽  
Angular Pressing ◽  
Globule Size ◽  
Alloy Microstructure ◽  
Hot Rolled ◽  
Zn Alloy

A combination of hot rolling and equal channel angular pressing (ECAP) was explored to generate globular microstructures in the Mg-3%Zn alloy after re-heating to the semisolid state. It was found that the single-step deformation of as-cast alloy via hot rolling at 350°C with a thickness reduction of 50% refined the alloy microstructure by creating deformation bands of the Mg (α) phase with a size of the order of tenths of micrometers. After re-heating to 630 °C, the microstructure transformed into spheroidal morphologies with an average globule size of 82 μm. An additional deformation of the hot-rolled alloy by the ECAP method at 250 °C further refined the alloy microstructure to sub-micrometer grains of lath and equiaxed shapes. After re-heating of this microstructure to 630 °C the average globule size reached 62 μm, which is roughly 25% smaller than that achieved for the hot-rolled precursor. The role of strain-induced melt activation (SIMA) techniques in generation of globular morphologies in Mg-based alloys after partial re-melting is discussed.

Influence of SPD by ECAP on Cu Properties

2008 ◽  
Vol 584-586 ◽  
pp. 310-314 ◽  
Author(s):  
Tibor Kvačkaj ◽  
Robert Kočiško ◽  
Michal Besterci ◽  
T. Donič ◽  
Imrich Pokorný ◽  
...  
Keyword(s):  
Grain Size ◽  
Equal Channel Angular Pressing ◽  
Bulk Material ◽  
Cell Structure ◽  
Effective Strain ◽  
Strength Properties ◽  
Structure Evolution ◽  
Plastic Properties ◽  
Angular Pressing ◽  
Average Grain Size

Equal channel angular pressing (ECAP) is a material processing method for developing an ultrafine-grained (UFG) structure by introducing severe plastic deformation (SPD) in a bulk material with no changes in its cross-section. Numerous analytical and numerical studies on equal channel angular pressing have been performed in recent years. The present work focuses on the effects of die geometry width is defined by the angle between two channels Φ, angle on outer corner of die Ψ (or radius R) and angle within internal corner (or radius r) of die on average effective strain after one pass route. Next, there are analyses of strength properties, plastic properties, fracture mechanism, as well as analyses of Cu structure evolution after SPD by ECAP technology, in the paper. The sixteen passes through the ECAP matrix were realized using route C. The following experimental results and their analyses, the biggest increase of strength and microhardness was proved already after 4th pass. Valuation of fracture surfaces shows that after 12th pass plastic fracture is transformed from transcrystalline ductile mixed fracture. After 4th pass, the avarage grain size decreased from initial approximate size 7 µm to 200 nm, whereby the average grain size was changeless after subsequent deformations. Possible mechanism of high-angle boundary nanograins evolution consists of formation of cell structure, subgrains that transform with the increase of deformation into nanograins with big-angle misorientation.

scholarly journals The Effect of Equal-Channel Angular Pressing on the Microstructure, the Mechanical and Corrosion Properties and the Anti-Tumor Activity of Magnesium Alloyed with Silver

Materials ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 3832 ◽  
Author(s):  
Yuri Estrin ◽  
Natalia Martynenko ◽  
Natalia Anisimova ◽  
Diana Temralieva ◽  
Mikhail Kiselevskiy ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Equal Channel Angular Pressing ◽  
Annexin V ◽  
Prismatic Slip ◽  
Corrosion Properties ◽  
Angular Pressing ◽  
Positive Side ◽  
Average Grain Size ◽  
Anti Tumor Activity

The effect of equal-channel angular pressing (ECAP) on the microstructure, texture, mechanical properties, corrosion resistance and cytotoxicity of two magnesium-silver alloys, Mg-2.0%Ag and Mg-4.0%Ag, was studied. Their average grain size was found to be reduced to 3.2 ± 1.4 μm and 2.8 ± 1.3 μm, respectively. Despite the substantial grain refinement, a drop in the strength characteristics of the alloys was observed, which can be attributed to the formation of inclined basal texture. On a positive side, an increase in tensile ductility to ~34% for Mg-2.0%Ag and ~27% for Mg-4.0%Ag was observed. This effect can be associated with the activity of basal and prismatic slip induced by ECAP. One of the ECAP regimes tested gave rise to a drop in the corrosion resistance of both alloys. An interesting observation was a cytotoxic effect both alloys had on tumor cells in vitro. This effect was accompanied with the release of lactate dehydrogenase, an increase in oxidative stress, coupled with the induction of NO-ions and an increase in the content of such markers of apoptosis as Annexin V and Caspase 3/7. Differences in the chemical composition and the processing history-dependent microstructure of the alloys did not have any significant effect on the magnitude of their antiproliferative effect.

An Investigation of Low Temperature Superplasticity of ZK40 Magnesium Alloy Subjected to Equal Channel Angular Pressing

2005 ◽  
Vol 488-489 ◽  
pp. 581-584 ◽  
Author(s):  
Li Lin ◽  
Li Jia Chen ◽  
Zhen Liu
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Initial Strain Rate ◽  
Angular Pressing ◽  
Average Grain Size ◽  
Mean Grain Size ◽  
Coarse Grains ◽  
Pass Through

Microstructure evolution and superplastic behaviors of ZK40 magnesium alloy were investigated in the temperature range of 473 ~ 623 K. Twinning occurred significantly after being processed by equal channel angular pressing (ECAP) for one pass through the die, the mean grain size was 5.6 µm. Finer grains can be obtained after further processing through ECAP, the average grain size of the alloy processed by ECAP for three passes was as low as 0.8 µm; this alloy exhibited low temperature superplasticity at 473 ~ 523 K, elongations at an initial strain rate of 1×10-3 s-1 were 260 % at 473 K and 612 % at 523 K, respectively. The incompatibility between fine and coarse grains was thought to be unfavorable to the improvement of superplasticity. Low temperature superplasticity of the as-ECAP ZK40 alloy can be attributed to the relatively finer grain size and the homogeneity of microstructure.

Equal Channel Angular Pressing in a Pearlitic Structured Steel

2007 ◽  
Vol 539-543 ◽  
pp. 4692-4697
Author(s):  
Jun Xia Huang ◽  
Jing Tao Wang
Keyword(s):  
Plastic Deformation ◽  
Grain Size ◽  
Shear Deformation ◽  
Equal Channel Angular Pressing ◽  
Ferrite Matrix ◽  
Nucleation And Growth ◽  
Additional Energy ◽  
Angular Pressing ◽  
Ultrafine Grained ◽  
Average Grain Size

Equal Channel Angular Pressing (ECAP) in a fully pearlitic structured steel 65Mn was successfully carried out at 923 K via route C in this study. The severe shear deformation of ECAP was accommodated by periodical bending, periodical shearing and shearing fracture etc in the pearlitic lamellae. The cementite in the pearlite has higher plastic deformation capability. Excessive imperfections may be introduced into the cementite, which supplies additional energy driving for the following spheroidization of cementite in subsequent processing. After five ECAP passes, the fully pearlitic lamellae evolved into a microstructure of ultrafine-grained ferrite matrix uniformly dispersed with finer cementite particles. The ferrite matrix is homogeneous with an average grain size of ~0.3 micrometers. Two possible mechanism for the spheroidization of cementite were proposed：heterogeneous growth of the fractured cementite fragments, and the precipitation of new fine spherical cementite particles through nucleation and growth.

Sign in / Sign up

Export Citation Format

Share Document