scholarly journals Effect of Naphthalene-Based Superplasticizer and Polycarboxylic Acid Superplasticizer on the Properties of Sulfoaluminate Cement

Materials ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 662
Author(s):  
Yonghua Wu ◽  
Qiqi Li ◽  
Guoxin Li ◽  
Shiying Tang ◽  
Mengdie Niu ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Hydration Products ◽  
Polycarboxylic Acid ◽  
X Ray Diffraction ◽  
Calcium Sulfoaluminate Cement ◽  
X Ray ◽  
Initial Setting Time ◽  
Calcium Sulfoaluminate ◽  
Initial Setting

In order to study what the effect of superplasticizers on the setting time, fluidity and compressive strength of calcium sulfoaluminate cement (CSA) a naphthalene-based superplasticizer (BNS) and a polycarboxylic acid superplasticizer (PC) were selected to interact with CSA pastes and ye’elimite, respectively. X-ray diffraction (XRD), thermogravimetric (TG) analysis and scanning electron microscopy (SEM) analytical methods were used to investigate the class, amount and microstructure of the CSA pastes and ye’elimite pastes hydration products under the effect of the superplasticizers. The results showed that the addition of BNS can promote ettringite generation and thus improve the early compressive strength. As the addition of BNS increased from 0.8 wt% to 2.0 wt%, the initial setting time was prolonged 10 min, the final setting time was prolonged 7 min, the 5 min fluidity was improved from no fluidity to 220 mm. However, as the addition of PC increased from 0.08 wt% to 0.20 wt%, the setting time of the PC just changed within 3 min; the 5 min fluidity increased from 110 mm to 195 mm and no 15 min fluidity at all was observed. AS seen by SEM, it can be stated that generated ettringite under the addition of PC was layered and lacking bonding, and its morphology changed from rod-like to flake-like, leading to a decrease in early compressive strength.

Development of Injectable Calcium Phosphate Cement Adding with ZrO2

2007 ◽  
Vol 361-363 ◽  
pp. 347-350
Author(s):  
J.Y. Gong ◽  
Shu Xin Qu ◽  
Q. Cui ◽  
Jie Weng
Keyword(s):  
Compressive Strength ◽  
Calcium Phosphate ◽  
Setting Time ◽  
X Ray Diffraction ◽  
Liquid Component ◽  
X Ray ◽  
Initial Setting Time ◽  
Mass Fractions ◽  
Initial Setting ◽  
Diffraction Peaks

In the present study, ZrO2 was added into the injectable calcium phosphate cements (CPCs) to improve their mechanical strength. Different mass fractions of ZrO2 (5 %, 10 %, 15 %, 20%) were mixed with the powder components consisted of tricalcium phosphate (α-TCP) and hydroxyapatite (HA). Then formed the paste via adding the liquid component consisted of citric acid. The compressive strength, the injectability, the initial setting time and finial time of CPC were measured, respectively. X-ray diffraction (XRD) was employed to analyse the phase of as-prepared CPC. Scanning Electron Microscope (SEM) and Energy dispersive spertrum (EDS) were used to observe the morphology and indicate the element components of CPC. The compressive strength of ZrO2-CPC was higher than that of CPC without added ZrO2. The compressive strength got the maximal when the mass fraction of ZrO2 was 15%. It had no effect on the injectability with adding ZrO2, which were 89 % to 92 %. It had a slight down-regulation of the initial and final setting time with adding ZrO2. SEM showed that there was amounts needle-like substance in CPC, which might be related to the improvement of compressive strength of CPC. XRD showed that there were HA, a few of α-TCP and ZrO2 diffraction peaks in CPCs. The present results indicate that it is feasible to improve the compressive strength of injectable CPC via adding ZrO2.

Modification Effects of Nano-CaCO3 on Engineering Performance of Cement Grouts

2020 ◽  
Vol 20 (8) ◽  
pp. 5043-5048
Author(s):  
Xiang Qiu ◽  
Huangbin Jiang ◽  
Guijin Zhang
Keyword(s):  
Yield Stress ◽  
Cement Hydration ◽  
Setting Time ◽  
X Ray Diffraction ◽  
Bleeding Rate ◽  
X Ray ◽  
Initial Setting Time ◽  
Study Results ◽  
Initial Setting ◽  
Cement Grouts

Efficacy of added nano-CaCO3 (NC) on engineering performances, including fluidity, initial setting time, bleeding rate and yield stress of cement grouts was investigated in this study. Results showed that the fluidity and bleeding rate for NC-cement (NCC) composite grout first decreased with increased NC content (i.e., ratio of NC mass to cement mass) and then slightly recovered as the NC content exceeded 2%. The initial setting time was always reduced while the yield stress increased with increased NC content. The microstructure of NCC was analyzed by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). It was found that the NC can promote the cement hydration, but an excess amount of NC will inhibit the cement hydration and affect the engineering performances of cement grouts. The optimum NC content for modification of cement grouts was thus 2%.

scholarly journals Properties of calcium sulfoaluminate cement-based grouting materials with LiAl-layered double hydroxides slurries

2020 ◽  
Vol 29 ◽  
pp. 2633366X2092652 ◽  
Author(s):  
Haiyan Li ◽  
Xianping Wang ◽  
Xuemao Guan ◽  
Dinghua Zou
Keyword(s):  
Compressive Strength ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Layered Double Hydroxides ◽  
Setting Time ◽  
Hydration Products ◽  
Calcium Sulfoaluminate Cement ◽  
Calcium Sulfoaluminate ◽  
Double Hydroxides

In this study, LiAl-layered double hydroxides Lithium aluminum hydrotalcite (LiAl-LDH) with different specific surface area were prepared by the separate nucleation and aging steps (SNAS) method and then were employed to prepare calcium sulfoaluminate cement-based grouting material (CBGM) paste. The influence of LiAl-LDH slurries on fresh and hardened properties of the CBGM paste was investigated in terms of fluidity, stability, setting time, and compressive strength. Additionally, the hydration process and hydration products of the CBGM paste were characterized by hydration heat, X-ray diffraction, differential thermal analysis–thermogravimetry, and Fourier transform infrared analyses. The acquired results illustrated that LiAl-LDH with larger specific surface area led to a faster hydration rate at early age, a lower fluidity, a shorter setting time, and a higher stability. Furthermore, due to the crystal nucleation effect, the addition of LiAl-LDH slurries did not cause a new phase to form but changed the morphology and increased the amount of hydration products, yielding higher compressive strength.

scholarly journals Durability and Microstructure Properties of Concrete with Arabic Gum Biopolymer Admixture

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Abdeliazim Mustafa Mohamed ◽  
Mohd Hanim Osman ◽  
Hichem Smaoui ◽  
Mohd Azreen Mohd Ariffin
Keyword(s):  
Setting Time ◽  
Hardened Concrete ◽  
X Ray Diffraction ◽  
Arabic Gum ◽  
X Ray ◽  
Initial Setting Time ◽  
Objective Evidence ◽  
Flow Table ◽  
Mechanical And Physical Properties ◽  
Initial Setting

Arabic gum biopolymer (AGB) has recently been demonstrated to improve mechanical and physical properties of fresh and hardened concrete which makes it a promising sustainable and environmentally friendly water-reducing admixture. The present work focuses on the effect of added AGB on the workability, setting time, and durability of concrete. Furthermore, a microstructure analysis is conducted to provide objective evidence and support for previous findings and hypothetic interpretations. Flow table experiments are conducted on Portland cement mortar mixed with different percentages of AGB to evaluate the workability. The initial setting time of cement paste is measured for different AGB contents. X-ray fluorescence tests are performed on cement-AGB mix powder to determine its chemical composition. Carbonation depth in AGB concrete samples is estimated to assess durability. AGB-added cement powder was subjected to X-ray diffraction and SEM tests to determine the rate of hydration and to expose the microstructure properties of AGB cement mix and help explain its macroscopic behavior, respectively.

scholarly journals Influence of Ultrafine Natural Steatite Powder on Setting Time and Strength Development of Cement

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
K. Sudalaimani ◽  
M. Shanmugasundaram
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Element Distribution ◽  
Strength Development ◽  
X Ray Diffraction ◽  
Dormant Period ◽  
Initial Setting Time ◽  
Final Setting Time ◽  
Initial Setting ◽  
Cement Binder

This paper deals with the setting time and pozzolanic activity of cement when ultra fine natural steatite powder (UFNSP) is used as replacement for cement. Initial setting time, final setting time, and mortar cube strength were studied, due to the replacement of ultra fine natural steatite powder with cement at 5%, 10%, 15%, 20%, and 25% by mass of cement. The setting time of fresh cement-binder paste and compressive strength of mortar cubes are observed. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were applied to investigate the microstructural behaviour and chemical element distribution inside cement-binder matrix. Results indicate that the length of dormant period is shortened. The replacement of ultra fine natural steatite powder with cement reduces initial setting time, and final setting time and increases mortar cube compressive strength.

Behavior of Cement Pastes and Mortar Containing Phosphogypsum

2015 ◽  
Vol 668 ◽  
pp. 181-188 ◽  
Author(s):  
Hanan El Nouhy ◽  
Enas Khattab ◽  
Sayieda Zeedan
Keyword(s):  
Compressive Strength ◽  
Setting Time ◽  
Blended Cement ◽  
X Ray Diffraction ◽  
Cement Pastes ◽  
Initial Setting Time ◽  
Second Stage ◽  
Setting Times ◽  
Initial Setting ◽  
Two Stages

The aim of this study is to investigate the effects of phosphogypsum on the properties of both cement pastes and mortars. Normal Portland cement CEM Ι 32,5N, Limestone Blended cement CEM ΙΙ B-L32,5N, and Slag cement CEM ΙΙ A-S32,5N were used. These cements were partially substituted by 0,2,4,6,8,10,and 15% of phosphogypsum. The test program was divided to two stages. In the first stage, tests were conducted according to BSEN 196, namely setting times (initial and final), soundness, and compressive strength (at ages 7 and 28 days). In the second stage, X-ray diffraction (XRD), and scanning electron microscope (SEM) were conducted on selected mixes from first stage. The results show that the three types of cements with the various replacement percentages of phosphogypsum met the limit of initial setting time, as well as, provided soundness of 2 mm. Also, in terms of compressive strength, it was proven, that it is possible to partially replace the three tested types of cements by phosphogypsum by up to 8%and 15% with regard to cement/sand ratio of (1:3) and (1:2) respectively.

scholarly journals Effect of Alkaline Salts on Calcium Sulfoaluminate Cement Hydration

Molecules ◽  
2021 ◽  
Vol 26 (7) ◽  
pp. 1938
Author(s):  
Luís Urbano D. Tambara Júnior ◽  
Janaíde C. Rocha ◽  
Malik Cheriaf ◽  
Pilar Padilla-Encinas ◽  
Ana Fernández-Jiménez ◽  
...  
Keyword(s):  
Cement Hydration ◽  
Hydration Products ◽  
Reaction Products ◽  
X Ray Diffraction ◽  
Calcium Sulfoaluminate Cement ◽  
Hydration Kinetics ◽  
Sodium Salts ◽  
X Ray ◽  
Calcium Sulfoaluminate ◽  
Ettringite Formation

This work analyzes the effect of the presence of 5 wt.% of solid sodium salts (Na2SO4, Na2CO3, and Na2SiO3) on calcium sulfoaluminate cement (CSA) hydration, addresses hydration kinetics; 2-, 28-, and 90-d mechanical strength, and reaction product microstructure (with X-ray diffraction (XRD), and Fourier transform infrared spectroscopy, (FTIR). The findings show that the anions affect primarily the reactions involved. Ettringite and AH3, are the majority hydration products, while monosulfates are absent in all of the samples. All three salts hasten CSA hydration and raise the amount of ettringite formed. Na2SO4 induces cracking in the ≥28-d pastes due to post-hardening gypsum and ettringite formation from the excess SO42– present. Anhydrite dissolves more rapidly in the presence of Na2CO3, prompting carbonation. Na2SiO3 raises compressive strength and exhibits strätlingite as one of its reaction products.

Performance of High-Efficiency Liquid Cement Setting Accelerator with Alkali-Free and its Acceleration Mechanism

2013 ◽  
Vol 377 ◽  
pp. 69-73
Author(s):  
Yan Wang ◽  
Jun Wang ◽  
Shu Heng Qiu ◽  
Fei Gao ◽  
Rui Gu
Keyword(s):  
Compressive Strength ◽  
High Efficiency ◽  
Bending Strength ◽  
Setting Time ◽  
X Ray Diffraction ◽  
Initial Setting Time ◽  
Acceleration Mechanism ◽  
Initial Setting ◽  
Strength Retention ◽  
Cement Setting

A kind of non-alkali high efficiency liquid cement setting accelerator named ZJ-NSA was developed by regulating the chemical composition of polymerized aluminum sulfate in this paper. The results show that the initial setting time and the final setting time are sharply shortened to 2 minutes 48 seconds and 4 minutes 37 seconds respectively, and the 1 d-aged compressive strength reach to 8.6MPa when it is mixed into P.O42.5 Portland cement with 5% addition; meanwhile, its compressive strength and bending strength retention at the age of 1d and 28d reach to 79.63%, 81.89% and 78.13%, 97.89% respectively. Phase characteristics on the hydrated cement specimens by means of x-ray diffraction (XRD) and differential scanning calorimeter (DSC) were analyzed and the acceleration mechanism was discussed.

Influence of Triethanolamine on the Properties of Cement-Based Materials

2017 ◽  
Vol 898 ◽  
pp. 2010-2017 ◽  
Author(s):  
Xiao Ying Wang ◽  
Ming Zhang Lan ◽  
Wei Fang Hou ◽  
Bin Feng Xiang ◽  
Xu Dong Zhao
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Hydration ◽  
Setting Time ◽  
Cementitious Materials ◽  
Hydration Products ◽  
Initial Setting Time ◽  
Final Setting Time ◽  
Retarding Effect ◽  
Initial Setting

The effects of triethanolamine on the compressive strength and setting time of fly ash cementitious materials, slag cementitious materials, and limestone cementitious materials were investigated. The results show that the dosage of 0.04% of triethanolamine can significantly improve the 3d, 7d and 28d compressive strength of fly ash cementitious materials. It possesses less impact on the setting time. The dosage of 0.04% of triethanolamine can significantly improve the 3d and 7d compressive strength of slag cementitious materials while the effect of late strength is not obvious. It extends the initial setting time and the final setting time is not changed, which has retarding effect. The results of hydration heat and XRD show that triethanolamine extends the induction period of cement hydration, and gypsum is exhausted in advance during the hydration process. Triethanolamine promotes the transformation of AFt to AFm and there is no effect on the type of hydration products.

scholarly journals Strength Performance and Microstructure of Calcium Sulfoaluminate Cement-Stabilized Soft Soil

2021 ◽  
Vol 13 (4) ◽  
pp. 2295
Author(s):  
Hailong Liu ◽  
Jiuye Zhao ◽  
Yu Wang ◽  
Nangai Yi ◽  
Chunyi Cui
Keyword(s):  
Soft Soil ◽  
Hydration Product ◽  
X Ray Diffraction ◽  
Calcium Sulfoaluminate Cement ◽  
Strength Performance ◽  
X Ray ◽  
Calcium Sulfoaluminate ◽  
Stabilized Soil ◽  
Calcium Silicates ◽  
Hydrated Calcium

Calcium sulfoaluminate cement (CSA) was used to stabilize a type of marine soft soil in Dalian China. Unconfined compressive strength (UCS) of CSA-stabilized soil was tested and compared to ordinary Portland cement (OPC); meanwhile the influence of amounts of gypsum in CSA and cement contents in stabilized soils on the strength of stabilized soils were investigated. X-ray diffraction (XRD) tests were employed to detect generated hydration products, and scanning electron microscopy (SEM) was conducted to analyze microstructures of CSA-stabilized soils. The results showed that UCS of CSA-stabilized soils at 1, 3, and 28 d firstly increased and then decreased with contents of gypsum increasing from 0 to 40 wt.%, and CSA-stabilized soils exhibited the highest UCS when the content of gypsum equaled 25 wt.%. When the mixing amounts of OPC and CSA were the same, CSA-stabilized soils had a significantly higher early strength (1 and 3 d) than OPC. For CSA-stabilized soil with 0 wt.% gypsum, monosulfate (AFm) was detected as a major hydration product. As for CSA-stabilized soil with certain amounts of gypsum, the intensity of ettringite (Aft) was significantly higher than that in the sample hydrating without gypsum, but a tiny peak of AFm also could be detected in the sample with 15 wt.% gypsum at 28 d. Additionally, the intensity of AFt increased with the contents of gypsum increasing from 0 to 25 wt.%. When contents of gypsum increased from 25 to 40 wt.%, the intensity of AFt tended to decrease slightly, and residual gypsum could be detected in the sample with 40 wt.% gypsum at 28 d. In the microstructure of OPC-stabilized soils, hexagonal plate-shaped calcium hydroxide (CH) constituted skeleton structures, and clusters of hydrated calcium silicates (C-S-H) gel adhered to particles of soils. In the microstructure of CSA-stabilized soils, AFt constituted skeleton structures, and the crystalline sizes of ettringite increased with contents of gypsum increasing; meanwhile, clusters of the aluminum hydroxide (AH3) phase could be observed to adhere to particles of soils and strengthen the interaction.

Sign in / Sign up

Export Citation Format

Share Document