scholarly journals Process Optimization of In Situ Magnetic-Anisotropy Spark Plasma Sintering of M-Type-Based Barium Hexaferrite BaFe12O19

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2650
Author(s):  
Haetham G. Mohammed ◽  
Thar Mohammed Badri Albarody ◽  
Susilawati Susilawati ◽  
Soheil Gohari ◽  
Aris Doyan ◽  
...  
Keyword(s):  
Magnetic Field ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Barium Hexaferrite ◽  
Optimum Process ◽  
Plasma Sintering ◽  
In Series ◽  
Spark Plasma ◽  
Measure Of Performance

This paper introduces a new spark plasma sintering technique that is able to order crystalline anisotropy by in-series/in situ DC electric coupled magnetic field. The process control parameters have been investigated on the production of anisotropic BaFe12O19 magnets based on resulted remanence (Mr). Sintering holding time (H.T.), cooling rate (C.R.), pressure (P), and sintering temperature (S.T.) are optimized by Taguchi with L9 orthogonal array (OA). The remanent magnetization of nanocrystalline BaFe12O19 in parallel (Mrǁ) and perpendicular (MrꞱ) to the applied magnetic field was regarded as a measure of performance. The Taguchi study calculated optimum process parameters, which significantly improved the sintering process based on the confirmation tests of BaFe12O19 anisotropy. The magnetic properties in terms of Mrǁ and MrꞱ were greatly affected by sintering temperature and pressure according to ANOVA results. In addition, regression models were developed for predicting the Mrǁ as well as MrꞱ respectively.

The Cu Matrix Strengthened by TiH2–C In-Situ Synthesized via Mechanical Milling and Spark Plasma Sintering

2021 ◽  
Vol 21 (4) ◽  
pp. 2687-2691
Author(s):  
Nguyen Thi ◽  
Hoang Oanh ◽  
Nguyen Hoang Viet
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Sintering Temperature ◽  
Annealing Treatment ◽  
High Energy ◽  
Composite Powders ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tic Nanoparticles

The present work is focused on the fabrication and the investigation of microstructures of copperbased TiC nanocomposites produced by mechanical milling in a high energy planetary ball mill. TiH2, carbon and copper powders were used as starting materials in which In-Situ reaction between carbon and TiH2 occurs to form TiC nanoparticles. The mixture powders of Cu–TiH2–C were milled for 12 h at 450 rpm in Argon gas. Annealing treatment process at 950 °C for 2 h was applied for as-milled composite powders to enhance In-Situ reaction. The consolidation of composite powders was conducted by spark plasma sintering under uniaxial pressing of 70 MPa. Sintering procedure was done at 950 and 1000 °C for 5 min. The results indicated that as TiC nanoparticles are formed after sintering at 950 °C and the TiC particles are increased up at higher sintering temperature of 1000 °C. Fracture surface of sintered samples shows ductile mode. HR-TEM image showed the crystal size of copper was about 10 nm for sample sintered at 1000 °C. The hardness and relative density of the nanocomposites increase when increasing sintering temperature.

Microstructural Characterization of In Situ TiB Whiskers in Ti MMCs Fabricated by SPS

2007 ◽  
Vol 336-338 ◽  
pp. 1310-1312
Author(s):  
Hai Bo Feng ◽  
De Chang Jia ◽  
Yu Zhou ◽  
Qing Chang Meng
Keyword(s):  
Electron Microscopy ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Microstructural Characterization ◽  
Average Diameter ◽  
Matrix Composites ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

The in situ TiB whisker reinforced titanium matrix composites were prepared by mechanical alloying followed by spark plasma sintering. X-ray diffraction, scanning electron microscopy and transmission electron microscopy were used to characterize the microstructure of the TiB whiskers. The effect of sintering temperature on morphologies of in situ TiB whiskers was evaluated. With the increase of spark plasma sintering temperature, the average diameter of in situ TiB whiskers increased. The in situ TiB whiskers exhibited a hexagonal shape with (100), (101) and (10 1 ) planes at the transverse section and a growth orientation of [010]TiB direction.

In Situ TiB Reinforced Titanium Metal Matrix Composites Prepared by Spark Plasma Sintering

2005 ◽  
Vol 502 ◽  
pp. 189-194
Author(s):  
Yu Zhou ◽  
Hai Bo Feng ◽  
De Chang Jia
Keyword(s):  
Spark Plasma Sintering ◽  
Volume Fraction ◽  
Sintering Temperature ◽  
Matrix Composites ◽  
Titanium Matrix ◽  
Cubic Lattice ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Crystallographic Planes

In situ synthesized TiB reinforced titanium matrix composites of Ti-B and Ti-TiB2 systems have been prepared by spark plasma sintering at 800-1200 °C under 20 MPa for 5 min. The effects of sintering temperature and reinforcement volume fraction on flexural strength, Young’s modulus and fracture toughness of the composites were investigated. The in situ synthesized TiB reinforcements are randomly and uniformly distributed in titanium matrix. The TiB whiskers are aligned along [010] direction, and the crystallographic planes of the TiB needles are always of the type (100), (101) and (10 1) . The parallel TiB were observed in β-Ti grains in both of the investigated composites. The in situ TiB needle is likely to grow along [010] direction which is parallel to [111] direction of cubic lattice of β-Ti phase.

Efffect of Spark Plasma Sintering Temperature on Mechanical Properties of In Situ TiB/Ti Composites

2014 ◽  
Vol 881-883 ◽  
pp. 923-926
Author(s):  
Xiang Bo Shen ◽  
Zhao Hui Zhang ◽  
Mao Sheng Cao ◽  
Fu Chi Wang
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Spark Plasma Sintering ◽  
Vickers Microhardness ◽  
Sintering Temperature ◽  
Matrix Composites ◽  
Titanium Matrix ◽  
Plasma Sintering ◽  
Spark Plasma

The in-situ synthesized TiB reinforced titanium matrix composites have been prepared by spark plasma sintering technique at 950–1250°C, using mixtures of 10wt% TiB2 and 90wt% Ti powders. The effects of the sintering temperature on the mechanical properties (Vickers microhardness, yield strength and Young`s modulus) of the composites were investigated. SEM was used to analyze the reaction process and the microstructure of the compacts synthesized at different sintering temperatures. The results indicated that the in situ synthesized TiB grow rapidly with increasing sintering temperature. The composite sintered at 1250°C have the highest relative density of 99.2%. However, the composite sintered at 950°C exhibits the best Vickers microhardness of 4.64GPa and yield strength of 989MPa, respectively.

scholarly journals Comparative Study of Reactive and Non-reactive Spark Plasma Sintering Routes for The Production of TaB2-TaC Composites

2021 ◽  
Author(s):  
Melis Kaplan Akarsu ◽  
Ipek Akin ◽  
Filiz Sahin ◽  
Gultekin Goller
Keyword(s):  
Spark Plasma Sintering ◽  
Oxidation Behavior ◽  
Sintering Temperature ◽  
Single Step ◽  
Reactive Sintering ◽  
Plasma Sintering ◽  
Average Grain Size ◽  
Significant Difference ◽  
Spark Plasma

Abstract The influence of two different spark plasma sintering-based processing routes (i.e., reactive SPS (RSPS) and non-reactive SPS) on the properties of TaB2-TaC composites was investigated. Ta2O5 and B4C powders were used as starting materials in the RSPS method, and synthesis and densification of TaB2-TaC composites were accomplished in a facile single step. The effect of sintering temperature and time on the microstructure and densification of the in-situ RSPS were investigated. The obtained results were compared with non-reactive spark plasma sintered TaB2-TaC composites. The highest densification (~ 99.5 %) was achieved for the TaB2-TaC composite with 6.64 vol% TaC after reactive sintering at 1550 °C under 40 MPa with a 5 min holding time. Although lower SPS temperature was used in the RSPS method, better densification and higher Vickers hardness were obtained compared to the non-reactive SPS. While platelet-shaped TaC formation was observed in both processes, the average grain size was smaller in the sample produced by the RSPS method. On the other hand, no significant difference was detected in fracture toughness and oxidation behavior of the composites produced by RSPS and non-reactive SPS.

Effect of spark plasma sintering temperature on structure and phase composition of Ti-Al-Nb-based alloys

2017 ◽  
Vol 59 (11-12) ◽  
pp. 1033-1036 ◽  
Author(s):  
Sherzod Kurbanbekov ◽  
Mazhyn Skakov ◽  
Viktor Baklanov ◽  
Batyrzhan Karakozov
Keyword(s):  
Phase Composition ◽  
Spark Plasma Sintering ◽  
Sintering Temperature ◽  
Plasma Sintering ◽  
Spark Plasma

scholarly journals Microstructure and properties of nano-laminated Y3Si2C2 ceramics fabricated via in situ reaction by spark plasma sintering

2021 ◽  
Vol 10 (3) ◽  
pp. 578-586
Author(s):  
Lin-Kun Shi ◽  
Xiaobing Zhou ◽  
Jian-Qing Dai ◽  
Ke Chen ◽  
Zhengren Huang ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Atomic Scale ◽  
Max Phase ◽  
X Ray Diffraction ◽  
Selected Area Electron Diffraction ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma ◽  
Diffraction Patterns

AbstractA nano-laminated Y3Si2C2 ceramic material was successfully synthesized via an in situ reaction between YH2 and SiC using spark plasma sintering technology. A MAX phase-like ternary layered structure of Y3Si2C2 was observed at the atomic-scale by high resolution transmission electron microscopy. The lattice parameters calculated from both X-ray diffraction and selected area electron diffraction patterns are in good agreement with the reported theoretical results. The nano-laminated fracture of kink boundaries, delamination, and slipping were observed at the tip of the Vickers indents. The elastic modulus and Vickers hardness of Y3Si2C2 ceramics (with 5.5 wt% Y2O3) sintered at 1500 °C were 156 and 6.4 GPa, respectively. The corresponding values of thermal and electrical conductivity were 13.7 W·m-1·K-1 and 6.3×105 S·m-1, respectively.

Sign in / Sign up

Export Citation Format

Share Document