scholarly journals Waste-Based One-Part Alkali Activated Materials

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2911
Author(s):  
Margarida Gonçalves ◽  
Inês Silveirinha Vilarinho ◽  
Marinélia Capela ◽  
Ana Caetano ◽  
Rui Miguel Novais ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Microstructural Analysis ◽  
Construction Materials ◽  
Sodium Metasilicate ◽  
High Compressive Strength ◽  
Hardened State ◽  
First Time ◽  
Furnace Slag ◽  
Alkali Activated

Ordinary Portland Cement is the most widely used binder in the construction sector; however, a very high carbon footprint is associated with its production process. Consequently, more sustainable alternative construction materials are being investigated, namely, one-part alkali activated materials (AAMs). In this work, waste-based one-part AAMs binders were developed using only a blast furnace slag, as the solid precursor, and sodium metasilicate, as the solid activator. For the first time, mortars in which the commercial sand was replaced by two exhausted sands from biomass boilers (CA and CT) were developed. Firstly, the characterization of the slag and sands (aggregates) was performed. After, the AAMs fresh and hardened state properties were evaluated, being the characterization complemented by FTIR and microstructural analysis. The binder and the mortars prepared with commercial sand presented high compressive strength values after 28 days of curing-56 MPa and 79 MPa, respectively. The mortars developed with exhausted sands exhibit outstanding compressive strength values, 86 and 70 MPa for CT and CA, respectively, and the other material’s properties were not affected. Consequently, this work proved that high compressive strength waste-based one-part AAMs mortars can be produced and that it is feasible to use another waste as aggregate in the mortar’s formulations: the exhausted sands from biomass boilers.

Synthesis and Characterisation of Slag Based Geopolymers

2010 ◽  
Vol 636-637 ◽  
pp. 155-160 ◽  
Author(s):  
C. Panagiotopoulou ◽  
Glykeria Kakali ◽  
Sotiris Tsivilis ◽  
T. Perraki ◽  
Maria Perraki
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Starting Material ◽  
Alkaline Media ◽  
High Compressive Strength ◽  
Geopolymer Matrix ◽  
Furnace Slag ◽  
Alkali Ion

In the present work the geopolymerisation of blast furnace slag (GGBS) under varying conditions is being investigated. The experimental comprises the following parts: i) dissolution of slag in alkaline media and the investigation of the effect of the alkali ion (K or Na) on the dissolution of Al+3 and Si4+, ii) synthesis of slag based geopolymers and the investigation of the effect of the Si/Al ratio and the kind of alkaline ion on the development of the compressive strength and iii) characterization of geopolymers by means of XRD, FTIR and SEM/EDS measurements. As it is concluded, blast furnace slag geopolymers exhibit high compressive strength, with the maximum being 112.7±2 MPa. The Si/Al ratio of the starting material is found to affect strongly the development of the geopolymer compressive strength. The microstructure of slag–based geopolymers and the incorporation of Ca in the geopolymer matrix are also discussed.

scholarly journals Machine Learning Approaches for Prediction of the Compressive Strength of Alkali Activated Termite Mound Soil

2021 ◽  
Vol 11 (11) ◽  
pp. 4754
Author(s):  
Assia Aboubakar Mahamat ◽  
Moussa Mahamat Boukar ◽  
Nurudeen Mahmud Ibrahim ◽  
Tido Tiwa Stanislas ◽  
Numfor Linda Bih ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Construction Materials ◽  
Curing Temperature ◽  
Sustainable Construction ◽  
Support Vector ◽  
Learning Approaches ◽  
Artificial Neural Network Ann ◽  
Curing Regime ◽  
Alkali Activated

Earth-based materials have shown promise in the development of ecofriendly and sustainable construction materials. However, their unconventional usage in the construction field makes the estimation of their properties difficult and inaccurate. Often, the determination of their properties is conducted based on a conventional materials procedure. Hence, there is inaccuracy in understanding the properties of the unconventional materials. To obtain more accurate properties, a support vector machine (SVM), artificial neural network (ANN) and linear regression (LR) were used to predict the compressive strength of the alkali-activated termite soil. In this study, factors such as activator concentration, Si/Al, initial curing temperature, water absorption, weight and curing regime were used as input parameters due to their significant effect in the compressive strength. The experimental results depict that SVM outperforms ANN and LR in terms of R2 score and root mean square error (RMSE).

scholarly journals Red Mud-Blast Furnace Slag-Based Alkali-Activated Materials

2021 ◽  
Vol 13 (20) ◽  
pp. 11298
Author(s):  
Alessio Occhicone ◽  
Mira Vukčević ◽  
Ivana Bosković ◽  
Claudio Ferone
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Red Mud ◽  
Blast Furnace Slag ◽  
Bauxite Residue ◽  
Sodium Silicate Solution ◽  
Silicate Solution ◽  
Waste Products ◽  
Furnace Slag ◽  
Alkali Activated

The aluminum Bayer production process is widespread all over the world. One of the waste products of the Bayer process is a basic aluminosilicate bauxite residue called red mud. The aluminosilicate nature of red mud makes it suitable as a precursor for alkali-activated materials. In this work, red mud was mixed with different percentages of blast furnace slag and then activated by sodium silicate solution at different SiO2/Na2O ratios. Obtained samples were characterized by chemical–physical analyses and compressive strength determination. Very high values of compressive strength, up to 50 MPa, even for high percentage of red mud in the raw mixture (70 wt.% of RM in powder mixture), were obtained. In particular, the higher compressive strength was measured for cubic samples containing 50 wt.% of RM, which showed a value above 70 MPa. The obtained mixtures were characterized by no or scarce environmental impact and could be used in the construction industry as an alternative to cementitious and ceramic materials.

scholarly journals The efficiency of plasticizing surfactants in alkali-activated cement mortars and concretes

2018 ◽  
Vol 230 ◽  
pp. 03016 ◽  
Author(s):  
Raisa Runova ◽  
Volodymyr Gots ◽  
Igor Rudenko ◽  
Oleksandr Konstantynovskyi ◽  
Oles’ Lastivka
Keyword(s):  
Compressive Strength ◽  
Blast Furnace Slag ◽  
Chemical Nature ◽  
Granulated Blast Furnace Slag ◽  
Cement Mortars ◽  
Alkaline Component ◽  
Property Modification ◽  
Furnace Slag ◽  
Alkali Activated ◽  
Strength In Bending

Functionality of mortar and concrete mixes is regulated by surfactants, which act as plasticizers. The molecular structure of these admixtures can be changed during hydration of alkali-activated cements (AAC). The objective was to determine the chemical nature of plasticizers effective for property modification of mortars and concretes based on AACs with changing content of granulated blast furnace slag from 0 to 100 %. The admixtures without ester links become more effective than polyesters when content of alkaline component increase. The admixtures effective in high alkaline medium were used in dry mixes for anchoring (consistency of mortar 150 mm by Vicat cone; 1 d tensile strength in bending / compressive strength of mortar 6.6 /30.6 MPa) and in ready-mixed concretes (consistency class changed from S1 to S3, S4 with consistency safety during 60 min; 3 d compressive strength of modified concrete was not less than the reference one without admixtures).

scholarly journals Alkali-activated concretes based on fly ash and blast furnace slag: Compressive strength, water absorption and chloride permeability

2020 ◽  
Vol 40 (2) ◽  
Author(s):  
Daniela Eugenia Angulo-Ramírez ◽  
William Gustavo Valencia-Saavedra ◽  
Ruby Mejía de Gutiérrez
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Fly Ash ◽  
Water Absorption ◽  
Blast Furnace Slag ◽  
Construction Materials ◽  
Chloride Ion ◽  
Chloride Permeability ◽  
Alkaline Activator ◽  
Furnace Slag

Concretes based on alkaliactivated binders have attracted considerable attention as new alternative construction materials, which can substitute Portland Cement (OPC) in several applications. These binders are obtained through the chemical reaction between an alkaline activator and reactive aluminosilicate materials, also named precursors. Commonly used precursors are fly ash (FA), blast furnace slag (GBFS), and metakaolin. The present study evaluated properties such as compressive strength, rate of water absorption (sorptivity), and chloride permeability in two types of alkaliactivated concretes (AAC): FA/GBFS 80/20 and GBFS/OPC 80/20. OPC and GBFS/OPC* concretes without alkaliactivation were used as reference materials. The highest compressive strength was observed in the FA/GBFS concrete, which reported 26,1% greater strength compared to OPC concrete after 28 days of curing. The compressive strength of alkaliactivated FA/GBFS 80/20 and GBFS/OPC 80/20 was 61 MPa and 42 MPa at 360 days of curing, respectively. These AAC showed low permeability to the chloride ion and a reduced water absorption. It is concluded that these materials have suitable properties for various applications in the construction sector.

scholarly journals Geopolymer Based on Mechanically Activated Air-cooled Blast Furnace Slag

Materials ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1134 ◽  
Author(s):  
Ilda Tole ◽  
Magdalena Rajczakowska ◽  
Abeer Humad ◽  
Ankit Kothari ◽  
Andrzej Cwirzen
Keyword(s):  
Compressive Strength ◽  
Blast Furnace ◽  
Portland Cement ◽  
Sodium Silicate ◽  
Blast Furnace Slag ◽  
Ball Mill ◽  
Efficient Solution ◽  
Building Materials ◽  
Furnace Slag ◽  
Alkali Activated

An efficient solution to increase the sustainability of building materials is to replace Portland cement with alkali-activated materials (AAM). Precursors for those systems are often based on water-cooled ground granulated blast furnace slags (GGBFS). Quenching of blast furnace slag can be done also by air but in that case, the final product is crystalline and with a very low reactivity. The present study aimed to evaluate the cementitious properties of a mechanically activated (MCA) air-cooled blast furnace slag (ACBFS) used as a precursor in sodium silicate alkali-activated systems. The unreactive ACBFS was processed in a planetary ball mill and its cementing performances were compared with an alkali-activated water-cooled GGBFS. Mixes based on mechanically activated ACBFS reached the 7-days compressive strength of 35 MPa and the 28-days compressive strength 45 MPa. The GGBFS-based samples showed generally higher compressive strength values.

Study of Manufacture Process and Properties of Tailings and Slag Based Geopolymers

2010 ◽  
Vol 156-157 ◽  
pp. 803-807
Author(s):  
Fu Sheng Niu ◽  
Shan Shan Zhou ◽  
Shu Xian Liu ◽  
Jin Xia Zhang
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Raw Material ◽  
Silicate Concentration ◽  
High Compressive Strength ◽  
Curing Period ◽  
Manufacture Process ◽  
Alkali Activated

The tailings and slag based geopolymers was prepared by sodium silicate, sodium hydroxide alkali-activated tailings and slag. The compressive strength in 7 d under different raw material proportion were tested. The result indicated that tailings and slag based geopolymers has high compressive strength . As the tailings in slag is 80%, the compressive strength in 7d can reach 45.10 MPa . As the Na2SiO3 to NaOH ratio is 0.5, the compressive strength in 7d can reach 63.79 MPa. As the NaOH and sodium silicate concentration in the solution is 35%, the compressive strength in 7d can reach 38.35 MPa respectively; As the curing period is 14 d , the compressive strength can reach 71.25 MPa. As the steel scoria in solid is 20%, the compressive strength in 7d can reach 61.86 MPa respectively.

scholarly journals Importance of Cation Species during Sulfate Resistance Tests for Alkali-Activated FA/GGBFS Blended Mortars

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3547
Author(s):  
Youngkeun Cho ◽  
Joo Hyung Kim ◽  
Sanghwa Jung ◽  
Yoonseok Chung ◽  
Yeonung Jeong
Keyword(s):  
Compressive Strength ◽  
Magnesium Sulfate ◽  
Sulfate Solution ◽  
Magnesium Ions ◽  
Sulfate Resistance ◽  
Granulated Blast Furnace Slag ◽  
Significant Difference ◽  
Furnace Slag ◽  
Alkali Activated ◽  
Magnesium Sulfate Solution

In this study, the changes in mass, compressive strength, and length of blended mortars were analyzed to investigate their sulfate resistance according to the ground granulated blast furnace slag (GGBFS) blending ratio and type of sulfate solution applied. All alkali-activated mortars showed an excellent sulfate resistance when immersed in a sodium sulfate (Na2SO4) solution. However, when immersed in a magnesium sulfate (MgSO4) solution, different sulfate resistance results were obtained depending on the presence of GGBFS. The alkali-activated GGBFS blended mortars showed a tendency to increase in mass and length and decrease in compressive strength when immersed in a magnesium sulfate solution, whereas the alkali-activated FA mortars did not show any significant difference depending on the types of sulfate solution applied. The deterioration of alkali-activated GGBFS blended mortars in the immersion of a magnesium sulfate solution was confirmed through the decomposition of C–S–H, which is the reaction product from magnesium ions, and the formation of gypsum (CaSO4·2H2O) and brucite (Mg(OH)2).

scholarly journals Characterization of Gypsum Composites Containing Cigarette Butt Waste for Building Applications

2020 ◽  
Vol 12 (17) ◽  
pp. 7022
Author(s):  
Mónica Morales-Segura ◽  
César Porras-Amores ◽  
Paola Villoria-Sáez ◽  
David Caballol-Bartolomé
Keyword(s):  
Compressive Strength ◽  
Bonding Strength ◽  
Ecological Footprint ◽  
Construction Materials ◽  
Construction Sector ◽  
Acoustic Performance ◽  
Cigarette Butts ◽  
Cigarette Butt ◽  
Performance Results

Cigarette butts are one of the most common waste on the planet and are not biodegradable, so they remain on the landscape for many years. Cigarette butt composition makes it suitable to be added during the manufacture of construction materials, so it can be considered a waste recovery material, helping to reduce the ecological footprint of the construction sector. This article shows the characterization of gypsum composites containing cigarette butt waste. Several gypsum specimens were prepared incorporating different percentages of cigarette butt waste (0.5%, 1.0%, 1.5%, 2.0% and 2.5%). Samples without waste additions were also prepared in order to compare the results obtained. Samples were tested for density, superficial hardness, flexural and compressive strength, bonding strength and acoustic performance. Results show that it is possible to add cigarette butts in a gypsum matrix, resulting in better mechanical behavior than traditional gypsums.

Comparison of Selected Properties of Portland Cement Based Materials and Alkali Activated Materials Based on Granulated Blast Furnace Slag

2016 ◽  
Vol 865 ◽  
pp. 107-113 ◽  
Author(s):  
Pavel Mec ◽  
Jana Boháčová ◽  
Josef Koňařík
Keyword(s):  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Water Glass ◽  
Sodium Metasilicate ◽  
Alkali Activation ◽  
Granulated Blast Furnace Slag ◽  
Cement Based Materials ◽  
One Year ◽  
Furnace Slag ◽  
Alkali Activated

Alkali activated systems are materials formed by alkali-activation of latent hydraulic or pozzolanic materials. The outcome is a polymeric structure with properties comparable to materials based on cement.The principle of the experiment is to compare selected properties of alkali-activated materials based on blast furnace slag and using various types of activator (sodium water glass, potassium water glass, DESIL AL and sodium metasilicate) to binders based on white and Portland cements of the highest quality. The samples were left for one year in environments simulating the conditions in the interior and exterior. Selected physical-mechanical properties were evaluated and compared.

Sign in / Sign up

Export Citation Format

Share Document