scholarly journals Soldering of Electronics Components on 3D-Printed Conductive Substrates

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3850
Author(s):  
Bartłomiej Podsiadły ◽  
Andrzej Skalski ◽  
Marcin Słoma
Keyword(s):  
Additive Manufacturing ◽  
Solder Joints ◽  
Rapid Development ◽  
Surface Preparation ◽  
Contact Angles ◽  
Electronic Components ◽  
Optimal Method ◽  
Structural Electronics ◽  
3D Printed ◽  
Composite Substrates

Rapid development of additive manufacturing and new composites materials with unique properties are promising tools for fabricating structural electronics. However, according to the typical maximum resolution of additive manufacturing methods, there is no possibility to fabricate all electrical components with these techniques. One way to produce complex structural electronic circuits is to merge 3D-printed elements with standard electronic components. Here, different soldering and surface preparation methods before soldering are tested to find the optimal method for soldering typical electronic components on conductive, 3D-printed, composite substrates. To determine the optimal soldering condition, the contact angles of solder joints fabricated in different conditions were measured. Additionally, the mechanical strength of the joints was measured using the shear force test. The research shows a possibility of fabricating strong, conductive solder joints on composites substrates prepared by additive manufacturing. The results show that mechanical cleaning and using additional flux on the composite substrates are necessary to obtain high-quality solder joints. The most repeatable joints with the highest shear strength values were obtained using reflow soldering together with low-temperature SnBiAg solder alloy. A fabricated demonstrator is a sample of the successful merging of 3D-printed structural electronics with standard electronic components.

3D Printed structural electronics: embedding and connecting electronic components into freeform electronic devices

2017 ◽  
Vol 47 (1) ◽  
pp. 35-41 ◽  
Author(s):  
Hessel H. H. Maalderink ◽  
Fabien B. J. Bruning ◽  
Mathijs M. R. de Schipper ◽  
John J. J. van der Werff ◽  
Wijnand W. C. Germs ◽  
...  
Keyword(s):  
Electronic Devices ◽  
Electronic Components ◽  
Structural Electronics ◽  
3D Printed

scholarly journals Additive manufacturing of anti-SARS-CoV-2 Copper-Tungsten-Silver alloy

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
John Robinson ◽  
Arun Arjunan ◽  
Ahmad Baroutaji ◽  
Miguel Martí ◽  
Alberto Tuñón Molina ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Surrogate Model ◽  
Data Transfer ◽  
Rapid Development ◽  
Virus Transmission ◽  
Design Data ◽  
Average Pore ◽  
Surrogate Modelling ◽  
Content Type ◽  
3D Printed

Purpose The COVID-19 pandemic emphasises the need for antiviral materials that can reduce airborne and surface-based virus transmission. This study aims to propose the use of additive manufacturing (AM) and surrogate modelling for the rapid development and deployment of novel copper-tungsten-silver (Cu-W-Ag) microporous architecture that shows strong antiviral behaviour against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Design/methodology/approach The research combines selective laser melting (SLM), in-situ alloying and surrogate modelling to conceive the antiviral Cu-W-Ag architecture. The approach is shown to be suitable for redistributed manufacturing by representing the pore morphology through a surrogate model that parametrically manipulates the SLM process parameters: hatch distance (h_d), scan speed (S_s) and laser power (L_p). The method drastically simplifies the three-dimensional (3D) printing of microporous materials by requiring only global geometrical dimensions solving current bottlenecks associated with high computed aided design data transfer required for the AM of porous materials. Findings The surrogate model developed in this study achieved an optimum parametric combination that resulted in microporous Cu-W-Ag with average pore sizes of 80 µm. Subsequent antiviral evaluation of the optimum architecture showed 100% viral inactivation within 5 h against a biosafe enveloped ribonucleic acid viral model of SARS-CoV-2. Research limitations/implications The Cu-W-Ag architecture is suitable for redistributed manufacturing and can help reduce surface contamination of SARS-CoV-2. Nevertheless, further optimisation may improve the virus inactivation time. Practical implications The study was extended to demonstrate an open-source 3D printed Cu-W-Ag antiviral mask filter prototype. Social implications The evolving nature of the COVID-19 pandemic brings new and unpredictable challenges where redistributed manufacturing of 3D printed antiviral materials can achieve rapid solutions. Originality/value The papers present for the first time a methodology to digitally conceive and print-on-demand a novel Cu-W-Ag alloy that shows high antiviral behaviour against SARS-CoV-2.

scholarly journals Effect of Sanding and Plasma Treatment of 3D-Printed Parts on Bonding to Wood with PVAc Adhesive

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1211
Author(s):  
Mirko Kariž ◽  
Daša Krapež Tomec ◽  
Sebastian Dahle ◽  
Manja Kitek Kuzman ◽  
Milan Šernek ◽  
...  
Keyword(s):  
Shear Strength ◽  
Plasma Treatment ◽  
Polylactic Acid ◽  
Wood Flour ◽  
Surface Preparation ◽  
Contact Angles ◽  
Fused Deposition Modelling ◽  
Water Contact ◽  
Fused Deposition ◽  
3D Printed

Additive manufacturing is becoming increasingly important for manufacturing end products, not just prototyping. However, the size of 3D-printed products is limited due to available printer sizes and other technological limitations. For example, making furniture from 3D-printed parts and wooden elements requires adequate adhesive joints. Since materials for 3D printing usually do not bond very well with adhesives designed for woodworking, they require special surface preparation to improve adhesion. In this study, fused deposition modelling (FDM) 3D-printed parts made of polylactic acid (PLA), polylactic acid with wood flour additive (Wood-PLA), and acrylonitrile-butadiene-styrene (ABS) polymers were bonded to wood with polyvinyl acetate (PVAc) adhesive. The surfaces of the samples were bonded as either non-treated, sanded, plasma treated, or sanded and plasma treated to evaluate the effect of each surface preparation on the bondability of the 3D-printed surfaces. Different surface preparations affected the bond shear strength in different ways. The plasma treatment significantly reduced water contact angles on all tested printing materials and increased the bond tensile shear strength of the adhesive used. The increase in bond strength was highest for the surfaces that had been both sanded and plasma treated. The highest increase was found for the ABS material (untreated 0.05 MPa; sanded and plasma treated 4.83 MPa) followed by Wood-PLA (from 0.45 MPa to 3.96 MPa) and PLA (from 0.55 MPa to 3.72 MPa). Analysis with a scanning electron microscope showed the smooth surfaces of the 3D-printed parts, which became rougher with sanding with more protruded particles, but plasma treatment partially melted the surface structures on the thermoplastic polymer surfaces.

AM-Serienproduktion für die Automobilindustrie/AM series production for the automotive industry

2020 ◽  
Vol 110 (11-12) ◽  
pp. 752-757
Author(s):  
Lukas Weiser ◽  
Marco Batschkowski ◽  
Niclas Eschner ◽  
Benjamin Häfner ◽  
Ingo Neubauer ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Automotive Industry ◽  
Series Production ◽  
Production Scale ◽  
Additive Fertigung ◽  
Small Series ◽  
Start Up ◽  
3D Printed ◽  
Component Quality

Die additive Fertigung schafft neue Gestaltungsfreiheiten. Im Rahmen des Prototypenbaus und der Kleinserienproduktion kann das Verfahren des selektiven Laserschmelzens genutzt werden. Die Verwendung in der Serienproduktion ist bisher aufgrund unzureichender Bauteilqualität, langen Anlaufzeiten sowie mangelnder Automatisierung nicht im wirtschaftlichen Rahmen möglich. Das Projekt „ReAddi“ möchte eine erste prototypische Serienfertigung entwickeln, mit der additiv gefertigte Bauteile für die Automobilindustrie wirtschaftlich produziert werden können. Additive manufacturing (AM) offers new freedom of design. The selective laser-powderbed fusion (L-PBF) process can be used for prototyping and small series production. So far, it has not been economical to use it on a production scale due to insufficient component quality, long start-up times and a lack of automation. The project ReAddi aims to develop a first prototype series production to cost-effectively manufacture 3D-printed components for the automotive industry.

Fused Filament Fabrication 3D Printed Polylactic Acid Electroosmotic Pumps

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Liang Wu ◽  
Stephen Beirne ◽  
Joan-Marc Cabot Canyelles ◽  
Brett Paull ◽  
Gordon G. Wallace ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Fused Filament Fabrication ◽  
Flexible Approach ◽  
Electroosmotic Pump ◽  
3D Printed ◽  
Electroosmotic Pumps

Additive manufacturing (3D printing) offers a flexible approach for the production of bespoke microfluidic structures such as the electroosmotic pump. Here a readily accessible fused filament fabrication (FFF) 3D printing...

scholarly journals 3D Printed Masks for Powders and Viruses Safety Protection Using Food Grade Polymers: Empirical Tests

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 617
Author(s):  
Ruben Foresti ◽  
Benedetta Ghezzi ◽  
Matteo Vettori ◽  
Lorenzo Bergonzi ◽  
Silvia Attolino ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Additive Manufacturing ◽  
Material Selection ◽  
Mechanical Resistance ◽  
Biological Safety ◽  
Fused Deposition ◽  
Industrial Grade ◽  
Safety Protection ◽  
3D Printed ◽  
Manufacturing Technologies

The production of 3D printed safety protection devices (SPD) requires particular attention to the material selection and to the evaluation of mechanical resistance, biological safety and surface roughness related to the accumulation of bacteria and viruses. We explored the possibility to adopt additive manufacturing technologies for the production of respirator masks, responding to the sudden demand of SPDs caused by the emergency scenario of the pandemic spread of SARS-COV-2. In this study, we developed different prototypes of masks, exclusively applying basic additive manufacturing technologies like fused deposition modeling (FDM) and droplet-based precision extrusion deposition (db-PED) to common food packaging materials. We analyzed the resulting mechanical characteristics, biological safety (cell adhesion and viability), surface roughness and resistance to dissolution, before and after the cleaning and disinfection phases. We showed that masks 3D printed with home-grade printing equipment have similar performances compared to the industrial-grade ones, and furthermore we obtained a perfect face fit by customizing their shape. Finally, we developed novel approaches to the additive manufacturing post-processing phases essential to assure human safety in the production of 3D printed custom medical devices.

scholarly journals Additive Manufacturing of Sensors for Military Monitoring Applications

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1455
Author(s):  
David T. Bird ◽  
Nuggehalli M. Ravindra
Keyword(s):  
Additive Manufacturing ◽  
High Performance ◽  
Sensor Technology ◽  
Distinct Advantage ◽  
Industrial Sectors ◽  
Sensor Fabrication ◽  
The Us ◽  
3D Printed ◽  
Maximum Protection ◽  
The Many

The US Department of Defense (DoD) realizes the many uses of additive manufacturing (AM) as it has become a common fabrication technique for an extensive range of engineering components in several industrial sectors. 3D Printed (3DP) sensor technology offers high-performance features as a way to track individual warfighters on the battlefield, offering protection from threats such as weaponized toxins, bacteria or virus, with real-time monitoring of physiological events, advanced diagnostics, and connected feedback. Maximum protection of the warfighter gives a distinct advantage over adversaries by providing an enhanced awareness of situational threats on the battle field. There is a need to further explore aspects of AM such as higher printing resolution and efficiency, with faster print times and higher performance, sensitivity and optimized fabrication to ensure that soldiers are more safe and lethal to win our nation’s wars and come home safely. A review and comparison of various 3DP techniques for sensor fabrication is presented.

scholarly journals Gold, Silver, and Electrum Electroless Plating on Additively Manufactured Laser Powder-Bed Fusion AlSi10Mg Parts: A Review

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 422
Author(s):  
Dana Ashkenazi ◽  
Alexandra Inberg ◽  
Yosi Shacham-Diamand ◽  
Adin Stern
Keyword(s):  
Additive Manufacturing ◽  
Low Cost ◽  
Ion Beam ◽  
Surface Finishing ◽  
Powder Bed Fusion ◽  
Laser Powder Bed Fusion ◽  
Powder Bed ◽  
Finishing Process ◽  
Gold Silver ◽  
3D Printed

Additive manufacturing (AM) revolutionary technologies open new opportunities and challenges. They allow low-cost manufacturing of parts with complex geometries and short time-to-market of products that can be exclusively customized. Additive manufactured parts often need post-printing surface modification. This study aims to review novel environmental-friendly surface finishing process of 3D-printed AlSi10Mg parts by electroless deposition of gold, silver, and gold–silver alloy (e.g., electrum) and to propose a full process methodology suitable for effective metallization. This deposition technique is simple and low cost method, allowing the metallization of both conductive and insulating materials. The AlSi10Mg parts were produced by the additive manufacturing laser powder bed fusion (AM-LPBF) process. Gold, silver, and their alloys were chosen as coatings due to their esthetic appearance, good corrosion resistance, and excellent electrical and thermal conductivity. The metals were deposited on 3D-printed disk-shaped specimens at 80 and 90 °C using a dedicated surface activation method where special functionalization of the printed AlSi10Mg was performed to assure a uniform catalytic surface yielding a good adhesion of the deposited metal to the substrate. Various methods were used to examine the coating quality, including light microscopy, optical profilometry, XRD, X-ray fluorescence, SEM–energy-dispersive spectroscopy (EDS), focused ion beam (FIB)-SEM, and XPS analyses. The results indicate that the developed coatings yield satisfactory quality, and the suggested surface finishing process can be used for many AM products and applications.

Sign in / Sign up

Export Citation Format

Share Document