scholarly journals The Influence of Short Coir, Glass and Carbon Fibers on the Properties of Composites with Geopolymer Matrix

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4599
Author(s):  
Kinga Korniejenko ◽  
Michał Łach ◽  
Janusz Mikuła
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Carbon Fibers ◽  
Matrix Material ◽  
Microstructural Analysis ◽  
Control Series ◽  
Coconut Fibers

The aim of the article is to analyze the influence of short coir, glass and carbon fiber admixture on the mechanical properties of fly ash-based geopolymer, such as: flexural and compressive strength. Glass fiber and carbon fibers have been chosen due to their high mechanical properties. Natural fibers have been chosen because of their mechanical properties as well as for the sake of comparison between their properties and the properties of the artificial ones. Fourth series of fly ash-based geopolymers for each fiber was cast: 1, 2, and 5% by weight of fly ash and one control series without any fibers. Each series of samples were tested on flexural and compressive strength after 7, 14, and 28 days. Additionally, microstructural analysis was carried out after 28 days. The results have shown an increase in compressive strength for composites with fibers—an improvement in properties between 25.0% and 56.5% depending on the type and amount of fiber added. For bending strength, a clear increase in the strength value is visible for composites with 1 and 2% carbon fibers (62.4% and 115.6%). A slight increase in flexural strength also occurred for 1% addition of glass fiber (4.5%) and 2% addition of coconut fibers (5.4%). For the 2% addition of glass fibers, the flexural strength value did not change compared to the value obtained for the matrix material. For the remaining fiber additions, i.e., 5% glass fiber as well as 1 and 5% coconut fibers, the flexural strength values deteriorated. The results of the research are discussed in a comparative context and the properties of the obtained composites are juxtaposed with the properties of the standard materials used in the construction industry.

scholarly journals Mechanical Properties of Basalt Fiber Reinforced Fly Ash-Based Geopolymer Composites

2020 ◽  
Author(s):  
Kinga Korniejenko ◽  
Gábor Mucsi ◽  
Nóra Papné Halyag ◽  
Roland Szabó ◽  
Dariusz Mierzwiński ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Microstructural Analysis ◽  
Basalt Fiber ◽  
Raw Material ◽  
Basalt Fibre ◽  
Control Series ◽  
Fibre Composites ◽  
Geopolymer Composites

This article analyses the influence of a short basalt fibre admixture on the mechanical properties of geopolymers, especially compressive strength. This preliminary research is the first step towards the development of a composite for fire resistant applications in civil engineering. This study investigates the behaviour of a fly ash based geopolymer containing basalt fibres. Fly ash from the coal power plant ‘Skawina’ (located in: Skawina, Lesser Poland, Poland) was used as the raw material. The chemical composition of this fly ash is typical for class F. Three series of fly ash based geopolymers were cast. In the first, short basalt fibres were added as 1% by weight of fly ash, in the second short basalt fibres were added as 2% by weight of fly ash and the third functioned as a control series without any fibres. Each series of samples were tested on compressive strength after 28, 14 and 7 days, and specimen density was determined. Additionally, microstructural analysis was carried out after 28 days. The results show that the addition of basalt fibres can improve the mechanical properties of geopolymer composites. Keywords: geopolymer, basalt fibre, composites, fire resistance

The Preparation of Fiber-Reinforced Foaming Desulfurization Gypsum

2013 ◽  
Vol 468 ◽  
pp. 28-31
Author(s):  
Lin Lin Li ◽  
Guo Zhong Li
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Glass Fiber ◽  
Thermal Insulation ◽  
Foaming Agent ◽  
Reinforcing Material ◽  
Different Content

Used the desulfurization gypsum, foaming agent and fly ash for molding thermal insulation foamed desulfurization gypsum, and studied the influence of different content of foaming agent on its density, mechanical properties and thermal conductivity. The result showed that when the content of foaming agent was 5%,the thermal conductivity was 0.052W/(m·K) reaching minimum, and the density of foamed desulfurization gypsum was 225Kg/m3 .To use glass fiber as reinforcing material for studying the effect of the vary content of glass fiber on strength of the material. The result showed that when the content of glass fiber was 1.5%, the flexural strength and compressive strength of the sample was increased 41.67%5.66% than the blank sample.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Strength Characteristics of High Strength Concrete (HSC) with and without Coarse Aggregate

2019 ◽  
Vol 9 (2) ◽  
pp. 4701-4704
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Silica Fume ◽  
High Strength Concrete ◽  
Mechanical Characteristics ◽  
Coarse Aggregate ◽  
High Strength ◽  
Set Up

This paper aimed to investigate the mechanical characteristics of HSC of M60 concrete adding 25% of fly ash to cement and sand and percentage variations of silica fumes 0%,5% and 10% to cement with varying sizes of 10mm,6mm,2mm and powder of granite aggregate with w/c of 0.32. Specimens are tested for compressive strength using 10cm X 10cmX10cm cubes for 7,14,28 days flexural strength was determined by using 10cmX10cmX50cm beam specimens at 28 days and 15cm diameter and 30cm height cylinder specimens at 28 days using super plasticizers of conplast 430 as a water reducing agent. In this paper the experimental set up is made to study the mechanical properties of HSC with and without coarse aggregate with varying sizes as 10mm, 6mm, 2mm and powder. Similarly, the effect of silica fume on HSC by varying its percentages as 0%, 5% and 10% in the mix studied. For all mixes 25% extra fly ash has been added for cement and sand.

Effects of Fly Ash Addition on Compressive Strength and Flexural Strength of Foamed Cement Composites

2013 ◽  
Vol 795 ◽  
pp. 664-668 ◽  
Author(s):  
Roshasmawi Abdul Wahab ◽  
Mohd Noor Mazlee ◽  
Shamsul Baharin Jamaludin ◽  
Khairul Nizar Ismail
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Cement Composites ◽  
Volume Percent ◽  
Foaming Agent ◽  
Cement Ratio ◽  
Water To Cement Ratio

In this study, the mixing of polystyrene (PS) beads and fly ash as a sand replacement material in foamed cement composites (FCC) has been investigated. Specifically, the mechanical properties such as compressive strength and flexural strength were measured. Different proportions of fly ash were added in cement composites to replace the sand proportion at 3 wt. %, 6 wt. %, 9 wt. % and 12 wt. % respectively. The water to cement ratio was fixed at 0.65 meanwhile ratios of PS beads used was 0.25 volume percent of samples as a foaming agent. All samples at different mixed were cured at 7 and 28 days respectively. Based on the results of compressive strength, it was found that the compressive strength was increased with the increasing addition of fly ash. Meanwhile, flexural strength was decreased with the increasing addition of fly ash up to 9 wt. %. The foamed cement composites with 12 wt. % of fly ash produced the highest strength of compressive strength meanwhile 3 wt. % of fly ash produced the highest strength of flexural strength.

Influence of Variable Temperature Curing on Mechanical Properties of Fly Ash Concrete

2011 ◽  
Vol 250-253 ◽  
pp. 178-181
Author(s):  
Ya Ding Zhao ◽  
Xue Ying Li ◽  
Ling Chao Kong ◽  
Wei Du
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Variable Temperature ◽  
Improve Performance ◽  
Curing Conditions ◽  
Fly Ash Concrete ◽  
Better Than

Under variable temperature curing conditions(30 oC ~70 oC), concrete with fly ash whose compressive strength, flexural strength, and dynamic elastic modulus are better than ones without fly ash.Compared with constant temperature 20oC, 50 oC and 70 oC, variable temperature curing(VTC) is benefit for the improvement of mechanical properties of 30% fly ash concrete, but which is no advantage to improve performance of 50% fly ash concrete.

scholarly journals Effect of fly ash on physical and mechanical properties of mortar

2019 ◽  
Vol 17 (6) ◽  
pp. 35
Author(s):  
Vu-An Tran
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Thermal Power ◽  
Setting Time ◽  
Physical And Mechanical Properties ◽  
Flow Density ◽  
Control Specimen

This research investigates the physical and mechanical properties of mortar incorporating fly ash (FA), which is by-product of Duyen Hai thermal power plant. Six mixtures of mortar are produced with FA at level of 0%, 10%, 20%, 30%, 40%, and 50% (by volume) as cement replacement and at water-to-binder (W/B) of 0.5. The flow, density, compressive strength, flexural strength, and water absorption tests are made under relevant standard in this study. The results have shown that the higher FA content increases the flow of mortar but significantly decreases the density of mixtures. The water absorption and setting time increases as the samples incorporating FA. Compressive strength of specimen with 10% FA is approximately equal to control specimen at the 91-day age. The flexural strength of specimen ranges from 7.97 MPa to 8.94 MPa at the 91-day age with the best result for samples containing 10% and 20% FA.

scholarly journals Use of waste paper ash or wood ash as substitution to fly ash in production of geopolymer concrete

2021 ◽  
Vol 30 (3) ◽  
pp. 464-476
Author(s):  
Haider Owaid ◽  
Haider Al-Baghdadi ◽  
Muna Al-Rubaye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Sodium Hydroxide ◽  
Wood Ash ◽  
Splitting Tensile Strength ◽  
Waste Paper ◽  
Geopolymer Concrete

Large quantities of paper and wood waste are generated every day, the disposal of these waste products is a problem because it requires huge space for their disposal. The possibility of using these wastes can mitigate the environmental problems related to them. This study presents an investigation on the feasibility of inclusion of waste paper ash (WPA) or wood ash (WA) as replacement materials for fly ash (FA) class F in preparation geopolymer concrete (GC). The developed geopolymer concretes for this study were prepared at replacement ratios of FA by WPA or WA of 25, 50, 75 and 100% in addition to a control mix containing 100% of FA. Sodium hydroxide (NaOH) solutions and sodium silicate (Na2SiO3) are used as alkaline activators with 1M and 10M of sodium hydroxide solution.The geopolymer concretes have been evaluated with respect to the workability, the compressive strength, splitting tensile strength and flexural strength. The results indicated that there were no significant differences in the workability of the control GC mix and the developed GC mixes incorporating WPA or WA. Also, the results showed that, by incorporating of 25–50% PWA or 25% WA, the mechanical properties (compressive strength, splitting tensile strength and flexural strength) of GC mixes slightly decreased. While replacement with 75–100% WPA or with 50–100% WA has reduced these mechanical properties of GC mixes. As a result, there is a feasibility of partial replacement of FA by up to 50% WPA or 25% WA in preparation of the geopolymer concrete.

Mechanical Properties of Reactive Powder Concrete Containing Fly Ash under Different Curing Regimes

2014 ◽  
Vol 597 ◽  
pp. 320-323 ◽  
Author(s):  
De Hong Wang ◽  
Yan Zhong Ju ◽  
Wen Zhong Zheng
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Ash Content ◽  
Reactive Powder Concrete ◽  
Steam Curing ◽  
Cement Ratio ◽  
Reactive Powder ◽  
Curing Regimes

Mechanical properties of reactive powder concrete (RPC) containing fly ash were investigated under different curing regimes (standard and steam curing) in this study. The experimental results indicate that, flexural strength of RPC increased considerably after steam curing, compared to the standard curing. Steam curing had no significant effect on compressive strength of RPC. Increasing the fly ash content improved the flexural strength of RPC under all curing regimes considerably. The compressive strength reached a maximum (103.8MPa) when the fly to ash and cement ratio is 0.3.

Study on Mechanical Properties of Soda Residue / Fly Ash Composite Cementitious Material

2011 ◽  
Vol 194-196 ◽  
pp. 1026-1029
Author(s):  
Bao Jia Li ◽  
Guo Zhong Li
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Portland Cement ◽  
Cementitious Material

The composite cementitious material was prepared with soda residue and fly ash. The mechanical properties were improved by mixing calcined lime and Portland cement, and the mechanism of admixture was researched. The results showed that the 28d flexural strength reached 3.59MPa and the 28d compressive strength reached 9.71MPa., when the proportion of soda residue and fly ash was 40:60 with 9% Portland cement and 7% calcined lime added.

Sign in / Sign up

Export Citation Format

Share Document