scholarly journals Influence of Silica Modulus and Curing Temperature on the Strength of Alkali-Activated Volcanic Ash and Limestone Powder Mortar

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5204
Author(s):  
Adeshina Adewale Adewumi ◽  
Mohd Azreen Mohd Ariffin ◽  
Mohammed Maslehuddin ◽  
Moruf Olalekan Yusuf ◽  
Mohammad Ismail ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Low Temperatures ◽  
Room Temperature ◽  
Volcanic Ash ◽  
Curing Temperature ◽  
Limestone Powder ◽  
Strength Development ◽  
Mass Ratio ◽  
Ambient Room Temperature ◽  
Alkali Activated

This present study evaluates the effect of silica modulus (Ms) and curing temperature on strengths and the microstructures of binary blended alkali-activated volcanic ash and limestone powder mortar. Mortar samples were prepared using mass ratio of combined Na2SiO3(aq)/10 M NaOH(aq) of 0.5 to 1.5 at an interval of 0.25, corresponding to Ms of 0.52, 0.72, 0.89, 1.05 and 1.18, respectively, and sole 10 M NaOH(aq). Samples were then subjected to ambient room temperature, and the oven-cured temperature was maintained from 45 to 90 °C at an interval of 15 °C for 24 h. The maximum achievable 28-day strength was 27 MPa at Ms value of 0.89 cured at 75 °C. Samples synthesised with the sole 10 M NaOH(aq) activator resulted in a binder with a low 28-day compressive strength (15 MPa) compared to combined usage of Na2SiO3(aq)/10 M NaOH(aq) activators. Results further revealed that curing at low temperatures (25 °C to 45 °C) does not favour strength development, whereas higher curing temperature positively enhanced strength development. More than 70% of the 28-day compressive strength could be achieved within 12 h of curing with the usage of combined Na2SiO3(aq)/10 M NaOH(aq). XRD, FTIR and SEM + EDX characterisations revealed that activation with combined Na2SiO3(aq)/10 M NaOH(aq) leads to the formation of anorthite (CaAl2Si2O8), gehlenite (CaO.Al2O3.SiO2) and albite (NaAlSi3O8) that improve the amorphosity, homogeneity and microstructural density of the binder compared to that of samples synthesised with sole 10 M NaOH(aq).

scholarly journals Mine Backfilling in the Permafrost, Part II: Effect of Declining Curing Temperature on the Short-Term Unconfined Compressive Strength of Cemented Paste Backfills

Minerals ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 172
Author(s):  
Mamert Mbonimpa ◽  
Parrein Kwizera ◽  
Tikou Belem
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Room Temperature ◽  
Freezing Temperature ◽  
Curing Temperature ◽  
Strength Development ◽  
Short Term ◽  
Practical Applications ◽  
Humidity Chamber ◽  
Paste Backfill

When cemented paste backfill (CPB) is used to fill underground stopes opened in permafrost, depending on the distance from the permafrost wall, the curing temperature within the CPB matrix decreases progressively over time until equilibrium with the permafrost is reached (after several years). In this study, the influence of declining curing temperature (above freezing temperature) on the evolution of the unconfined compressive strength (UCS) of CPB over 28 days’ curing is investigated. CPB mixtures were prepared with a high early (HE) cement and a blend of 80% slag and 20% General Use cement (S-GU) at 5% and 3% contents and cured at room temperature in a humidity chamber and under decreasing temperatures in a temperature-controlled chamber. Results indicate that UCS is higher for CPB cured at room temperature than under declining temperatures. UCS increases progressively from the stope wall toward the inside of the CPB mass. Under declines in curing temperature, HE cement provides better short-term compressive strength than does S-GU binder. In addition, the gradual decline in temperature does not appear to affect the fact that the higher the binder proportion, the greater the strength development. Therefore, UCS is higher for samples prepared with 5% than 3% HE cement. Findings are discussed in terms of practical applications.

scholarly journals Compressive Strength Gain Behavior and Prediction of Cement-Stabilized Macadam at Low Temperature Curing

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Yongli Xu ◽  
Guang Yang ◽  
Hongyuan Zhao
Keyword(s):  
Compressive Strength ◽  
Low Temperature ◽  
Curing Temperature ◽  
Strength Development ◽  
Construction Process ◽  
Strength Gain ◽  
Estimation Model ◽  
Maturity Method ◽  
Temperature Ranges ◽  
Natural Temperature

For cement-based materials, the curing temperature determines the strength gain rate and the value of compressive strength. In this paper, the 5% cement-stabilized macadam mixture is used. Three indoor controlled temperature curing and one outdoor natural curing scenarios are designed and implemented to study the strength development scenario law of compressive strength, and they are standard temperature curing (20°C), constant low temperature curing (10°C), day interaction temperature curing (varying from 6°C to 16°C), and one outdoor natural temperature curing (in which the air temperature ranges from 4°C to 20°C). Finally, based on the maturity method, the maturity-strength estimation model is obtained by using and analyzing the data collected from the indoor tests. The model is proved with high accuracy based on the validated results obtained from the data of outdoor tests. This research provides technical support for the construction of cement-stabilized macadam in regions with low temperature, which is beneficial in the construction process and quality control.

scholarly journals Machine Learning Approaches for Prediction of the Compressive Strength of Alkali Activated Termite Mound Soil

2021 ◽  
Vol 11 (11) ◽  
pp. 4754
Author(s):  
Assia Aboubakar Mahamat ◽  
Moussa Mahamat Boukar ◽  
Nurudeen Mahmud Ibrahim ◽  
Tido Tiwa Stanislas ◽  
Numfor Linda Bih ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Construction Materials ◽  
Curing Temperature ◽  
Sustainable Construction ◽  
Support Vector ◽  
Learning Approaches ◽  
Artificial Neural Network Ann ◽  
Curing Regime ◽  
Alkali Activated

Earth-based materials have shown promise in the development of ecofriendly and sustainable construction materials. However, their unconventional usage in the construction field makes the estimation of their properties difficult and inaccurate. Often, the determination of their properties is conducted based on a conventional materials procedure. Hence, there is inaccuracy in understanding the properties of the unconventional materials. To obtain more accurate properties, a support vector machine (SVM), artificial neural network (ANN) and linear regression (LR) were used to predict the compressive strength of the alkali-activated termite soil. In this study, factors such as activator concentration, Si/Al, initial curing temperature, water absorption, weight and curing regime were used as input parameters due to their significant effect in the compressive strength. The experimental results depict that SVM outperforms ANN and LR in terms of R2 score and root mean square error (RMSE).

scholarly journals Grinding Kinetics of Slag and Effect of Final Particle Size on the Compressive Strength of Alkali Activated Materials

Minerals ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 714 ◽  
Author(s):  
Evangelos Petrakis ◽  
Vasiliki Karmali ◽  
Georgios Bartzas ◽  
Konstantinos Komnitsas
Keyword(s):  
Particle Size ◽  
Compressive Strength ◽  
Particle Size Distribution ◽  
Size Distribution ◽  
Ageing Time ◽  
Reduction Rate ◽  
Curing Temperature ◽  
Alkali Activation ◽  
Final Particle ◽  
Alkali Activated

This study aims to model grinding of a Polish ferronickel slag and evaluate the particle size distributions (PSDs) of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e., temperature, curing, and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin–Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multifractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

scholarly journals Synthesis of Geopolymer from Inorganic Construction Waste

2013 ◽  
Vol 30 ◽  
pp. 45-51 ◽  
Author(s):  
Arbind Pathak ◽  
Vinay Kumar Jha
Keyword(s):  
Compressive Strength ◽  
Coal Fly Ash ◽  
Chemical Society ◽  
Raw Material ◽  
Curing Temperature ◽  
Alkali Concentration ◽  
Curing Time ◽  
Mass Ratio ◽  
Construction Waste ◽  
Alumino Silicate

Recently, the demolition of old houses and the construction of new buildings in Kathmandu valley are in the peak which in turn generates a huge amount of construction waste. There are two major types of construction wastes which are burden for disposal namely cement-sand-waste (CSW) and the coal fly ash (CFA). These construction wastes are rich source of alumino-silicate and thus used as raw material for the synthesis of geopolymer in this study. Geopolymers have been synthesized from CSW and CFA using NaOH-KOH and Na2SiO3 as activators. Some parameters like alkali concentration, amount of Na2SiO3 and curing time have been varied in order to improve the quality of geopolymeric product. The geopolymerization process has been carried out using 3-8M KOH/NaOH solutions, Na2SiO3 to CFA and CSW mass ratio of 0.25-2.00 and curing time variation from 5-28 days. The curing temperature was fixed at 40ºC in all the cases. 6M NaOH and 7M KOH solutions were found appropriate alkali concentrations while the ratio of sodium silicate to CSW and CFA of 0.5 and 1.75 respectively were found suitable mass ratio for the process of geopolymer synthesis. The maximum compressive strength of only 7.3 MPa after 15 days curing time with CSW raw material was achieved while with CFA, the compressive strength was found to be 41.9 MPa with increasing the curing time up to 28 days.DOI: http://dx.doi.org/10.3126/jncs.v30i0.9334Journal of Nepal Chemical Society Vol. 30, 2012 Page:  45-51 Uploaded date: 12/16/2013    

scholarly journals Strength and Durability Performance of Alkali-Activated Rice Husk Ash Geopolymer Mortar

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Yun Yong Kim ◽  
Byung-Jae Lee ◽  
Velu Saraswathy ◽  
Seung-Jun Kwon
Keyword(s):  
Compressive Strength ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Polymerization Reaction ◽  
Strength Development ◽  
Geopolymer Concrete ◽  
Portland Cement Concrete ◽  
Mix Proportion ◽  
Strength And Durability ◽  
Alkali Activated

This paper describes the experimental investigation carried out to develop the geopolymer concrete based on alkali-activated rice husk ash (RHA) by sodium hydroxide with sodium silicate. Effect on method of curing and concentration of NaOH on compressive strength as well as the optimum mix proportion of geopolymer mortar was investigated. It is possible to achieve compressive strengths of 31 N/mm2and 45 N/mm2, respectively for the 10 M alkali-activated geopolymer mortar after 7 and 28 days of casting when cured for 24 hours at 60°C. Results indicated that the increase in curing period and concentration of alkali activator increased the compressive strength. Durability studies were carried out in acid and sulfate media such as H2SO4, HCl, Na2SO4, and MgSO4environments and found that geopolymer concrete showed very less weight loss when compared to steam-cured mortar specimens. In addition, fluorescent optical microscopy and X-ray diffraction (XRD) studies have shown the formation of new peaks and enhanced the polymerization reaction which is responsible for strength development and hence RHA has great potential as a substitute for ordinary Portland cement concrete.

scholarly journals Impact of Temperature on the Strength Development of the Tailing-Waste Rock Backfill of a Gold Mine

2019 ◽  
Vol 2019 ◽  
pp. 1-9
Author(s):  
Bin Han ◽  
Shengyou Zhang ◽  
Wei Sun
Keyword(s):  
Compressive Strength ◽  
Mass Concentration ◽  
Critical Concentration ◽  
Curing Temperature ◽  
Strength Development ◽  
Gold Mine ◽  
Critical Interval ◽  
Cement Ratio ◽  
Rate Of Increase ◽  
The Impact

This study investigated the influencing rules of curing temperature (5, 10, 16, and 20°C), cement ratio (8%, 10%, 12%, and 14%), and mass concentration (70%, 73%, 74%, and 75%) on the strength of backfill. In addition, a scanning electron microscope (SEM) is employed to analyze the microtopography of the backfill. Experimental results indicate that the uniaxial compressive strength (UCS) of the backfill decreases as the curing temperature diminishes; temperature substantially influences the earlier strength of backfill (it is much significant below 10°C). In addition, as the cement ratio rises, the critical point for the impact of temperature on strength gradually moves toward a low-temperature zone; in pace with the slurry mass concentration increase, the compressive strength of the backfill also rises and its rate of increase enlarges after going beyond the critical concentration. In case the curing temperature is lower than 10°C, the extent of hydration is also low inside the backfill. Through experiments, the critical concentration of slurry in the Jinying gold mine is determined as 73%, and the critical interval of the cement ratio ranged between 10% and 12%. Corresponding measures can be taken to increase the strength of backfill in the Jinying Gold Mine by 129.9%. As a result, backfill collapse is effectively controlled.

Effect of Curing Regimes on Metakaolin Geopolymer Pastes Produced from Geopolymer Powder

2012 ◽  
Vol 626 ◽  
pp. 931-936 ◽  
Author(s):  
Liew Yun Ming ◽  
Kamarudin Hussin ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
Mohammed Binhussain ◽  
Luqman Musa ◽  
...  
Keyword(s):  
Room Temperature ◽  
Raw Materials ◽  
Solidification Process ◽  
Curing Temperature ◽  
Alkali Concentration ◽  
Strength Development ◽  
Curing Time ◽  
Curing Conditions ◽  
Metakaolin Geopolymer ◽  
Geopolymer Paste

The properties of metakaolin geopolymer paste are affected by the alkali concentration, the initial raw materials, solidification process, and amount of mixing water as well as the curing conditions. This study aimed to investigate the effect of curing temperature (room temperature, 40°C, 60°C, 80°C and 100°C) and curing time (6h, 12h, 24h, 48h and 72h) on the geopolymer pastes produced from geopolymer powder. The results showed that curing at room temperature was unfeasible. Heat was required for the geopolymerization process, where strength increased as the curing temperature was increased. Moderate elevated curing temperature favored the strength development of geopolymer pastes in comparison with those treated with extreme elevated curing temperature. When geopolymer paste was subjected to extreme elevated curing temperature, shorter curing time should be used to avoid deterioration in strength gain. Similarly, longer curing time was recommended for moderate elevated curing temperature. The microstructure of geopolymer paste cured at moderate curing temperature showed obvious densification of structure. In contrast, the structure formed was weak and less compact at very high elevated curing temperature.

Sign in / Sign up

Export Citation Format

Share Document