scholarly journals Synthesis of High-Performance CSA Cements as Low Carbon OPC Alternative

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7057
Author(s):  
Bogdan-Catalin Marin ◽  
Georgeta Voicu ◽  
Stefania Stoleriu
Keyword(s):  
Electron Microscopy ◽  
High Performance ◽  
Ordinary Portland Cement ◽  
Raw Materials ◽  
Low Carbon ◽  
X Ray Diffraction ◽  
Cement Ratio ◽  
X Ray ◽  
Calcium Sulphoaluminate ◽  
Scanning Electron

Starting from natural raw materials, cements based calcium sulphoaluminate (CSA) clinkers have been successfully obtained as an eco-friendly alternative to ordinary Portland cement. CSA-based cements with ye’elimite as the main phase have been produced over the years and are widely used today. In this regard, the present paper considers the study of hydration processes for CSA pastes prepared with a water/cement ratio of 0.5 according to the EN-197 standard and their characterization by thermal analysis (DTA-TG), X-ray diffraction analysis (XRD), and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX). A mechanical strength of 60.9 MPa was the greatest achieved for mortars hardened for 28 days.

Influence of Fly Ash on Corrosion Resistance of Refractory Forsterite-Spinel Ceramics

2021 ◽  
Vol 325 ◽  
pp. 181-187
Author(s):  
Martin Nguyen ◽  
Radomír Sokolář
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Corrosion Resistance ◽  
Fly Ash ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transition Zones ◽  
Refractory Ceramics ◽  
Scanning Electron

This article examines the influence of fly ash on corrosion resistance of refractory forsterite-spinel ceramics by molten iron as a corrosive medium. Fly ash in comparison with alumina were used as raw materials and sources of aluminium oxide for synthesis of forsterite-spinel refractory ceramics. Raw materials were milled, mixed in different ratios into two sets of mixtures and sintered at 1550°C for 2 hours. Samples were characterized by X-ray diffraction analysis and thermal dilatometric analysis. Crucibles were then made from the fired ceramic mixtures and fired together with iron at its melting point of 1535°C for 5 hours. The corrosion resistance was evaluated by scanning electron microscopy on the transition zones between iron and ceramics. Mixtures with increased amount of spinel had higher corrosion resistance and mixtures with fly ash were comparable to mixtures with alumina in terms of corrosion resistance and refractory properties.

Preparation and Properties of CaF2 Nano-Powder

2016 ◽  
Vol 680 ◽  
pp. 257-260
Author(s):  
Meng Yun Dong ◽  
Cheng Zhang ◽  
Jin Feng Xia ◽  
Hong Qiang Nian ◽  
Dan Yu Jiang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Particle Size ◽  
Sintering Temperature ◽  
Raw Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Nano Powder ◽  
Direct Precipitation ◽  
Scanning Electron

CaF2 nano-power was prepared by direct precipitation methods with Ca(NO3)2 and KF as raw materials. The influences of presintering temperature and sintering temperature on the particle size and distribution of CaF2 nano-power were studied by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). This study provided an experimental method for preparation of CaF2 nano-power. The results show that the best presintering temperature of CaF2 nano-power is 500°C and the best sintering temperature of CaF2 ceramic is 900°C.

Preparation and Properties of Sintering Brick from Iron Tailings

2012 ◽  
Vol 512-515 ◽  
pp. 1023-1027
Author(s):  
Ran Fang Zuo ◽  
Gao Xiang Du ◽  
Le Fu Mei ◽  
Wei Juan Guo ◽  
Jing Hui Liao
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Bulk Density ◽  
Raw Materials ◽  
Loss On Ignition ◽  
X Ray Diffraction ◽  
X Ray ◽  
Freeze Thaw ◽  
Scanning Electron

The main objective of this paper was to investigate the addition of iron tailing sintering brick production, in the presence of clay, coal refuses and bentonite. Mixtures containing raw materials of sintering brick and iron tailings were prepared at different proportions (up to 55 wt %), fired at 980°C. Freeze/thaw durability, drying and firing shrinkages were investigated as well as the loss on ignition, bulk density and compressive strength of the fired samples. Their mechanical and microstructure properties were also investigated by differential thermal analysis (DTA/TG), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that compressive strengths of the brick samples are higher than that required by the standards MU15 of GB5101-2003, up to 21.79Mpa with 40% iron tailings corresponding to its higher bulk density completely. Moreover, the results showed that it has such advantages as no lime blowing, uniform color, good freeze/thaw resistance and slight universal frost.

Study the Effect of HAp Content in PLA/HAp Microsphere on the Efficiency of Drug (Clindamycin) Loading Process

2013 ◽  
Vol 834-836 ◽  
pp. 559-562 ◽  
Author(s):  
Juntima Pradid ◽  
Wirunya Keawwattana ◽  
Siree Tangbunsuk
Keyword(s):  
Electron Microscopy ◽  
Thermal Process ◽  
High Performance ◽  
Core Shell ◽  
X Ray Diffraction ◽  
X Ray ◽  
Ultrasound Field ◽  
Sample Characterization ◽  
Core Shell Structure ◽  
Scanning Electron

An ultrasound field was applied to obtain Polylactic acid (PLA)/Hydroxyapatite (HAp) biocomposite microspheres with the specific core-shell structure to be applied as a carrier of a drug. The hydroxyapatite was obtained from crocodile bone by thermal process. Sample characterization was achieved by powder X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDX) Scanning electron microscopy (SEM) and High Performance Liquid Chromatography (HPLC). As the result, the PLA/HAp loading clindamycin with different polymer-to-ceramic part wt.% ratio (100:0, 90:10, 80:20, and 70:30) showed the agglomeration of sphere-like particles. In addition, the loading efficiency of clindamycin increased with increasing HAp content up to 20%.

Effects of Reductive Conditions on the Electrochemical Properties of LiFePO4/C Derived by Fe3+ Sources

2014 ◽  
Vol 1081 ◽  
pp. 313-317
Author(s):  
Yan Wen Lu ◽  
Yu Ge ◽  
Yue Feng Tang
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Raw Materials ◽  
Thermal Method ◽  
X Ray Diffraction ◽  
Sintering Atmosphere ◽  
X Ray ◽  
Electrochemical Capacity ◽  
One Step ◽  
Scanning Electron

A one-step carbon thermal method was used to prepare LiFePO4/C particles by using normal Fe2O3, LiH2PO4and sucrose as raw materials. The effect of H2content in the sintering atmosphere of N2on the morphology and the electrochemical performance were investigated. LiFePO4/C materials were characterized by X-ray diffraction, scanning electron microscopy and the elemental analyzer. The results show that the precursor sintering under the atmosphere of 8%H2+N2exhibits the highest electrochemical capacity (162.3 mAh/g at 0.1C) .

Archaeometric analysis of a fragment of molded stucco cornice with rope from the House of the Mithraeum (Mérida, Spain)

2021 ◽  
pp. 1-22
Author(s):  
Alicia Fernández Díaz ◽  
Ana María Bejarano Osorio ◽  
Macarena Bustamante-Álvarez ◽  
Dolores Julia Yusá Marco ◽  
Sofía Vicente Palomino ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Diffraction Data ◽  
Raw Materials ◽  
Compositional Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Technical Study ◽  
Scanning Electron

Abstract During the excavations carried out since 2017 in the House of the Mithraeum (Casa del Mitreo) in Mérida a collection of paintings was recovered from Room 11, which had been abandoned in the late 3rd c. CE after a fire. The remains included fragments of molded stucco cornices, with braided esparto grass ropes on the reverse that were used to attach them to the ceiling. This article presents the descriptive and technical study of the finds and their compositional analysis using scanning electron microscopy and X-ray diffraction. Data resulting from these analyses allow us to understand the fragments’ composition and technical execution, and even the possible circulation of workshops and raw materials.

Preparation of Cordierite–Mullite Composite Crucibles and Structure Characterization

2012 ◽  
Vol 430-432 ◽  
pp. 521-524
Author(s):  
Feng Feng Li ◽  
Jiao Du ◽  
Ming Xi Zhang ◽  
Wei Chao Yang ◽  
Yi Shen
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Raw Materials ◽  
Sintered Sample ◽  
Structure Characterization ◽  
X Ray Diffraction ◽  
X Ray ◽  
State Process ◽  
Sintered Temperature ◽  
Scanning Electron

Cordierite–mullite composite crucibles were prepared via high-temperature solid-state process by using burn talc, datong soil, knar clay, bentonite, quartz, feldspar and alumina as raw materials, waste porcelain powder as skeletal material. The main influencing factors such as the raw materials radio and calcination temperature were discussed. The microstructure of the sintered sample was analyzed with X-ray diffraction (XRD) and Scanning electron microscopy (SEM). The results show that the optimal prescription was sample II (13.34 wt% of burn talc, 10.496wt% datong soil, 40.65% knar clay, 15.00wt% waste porcelain powder,10.34wt% bentonite, 2.17wt% feldspar, 1.61wt% quartz, and 6.394wt% of alumina). The optimal sintered temperature was 1380°C and the holding time was 3 hours.

Experiment Study on the Effect of GGBFS on Frost Resistance of Concrete

2014 ◽  
Vol 629-630 ◽  
pp. 207-212 ◽  
Author(s):  
Shi Yi Zhang ◽  
Ying Fang Fan ◽  
Qi Wang
Keyword(s):  
Electron Microscopy ◽  
High Performance ◽  
Plain Concrete ◽  
Industrial Wastes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Scanning Electron

High volume utilization of industrial wastes and by products is the solution for high disposal coast. The anti-frost of high performance concrete is a key factor for safe utilization of concrete structure containing industrial wastes under severe environment. In this paper, to understand the property on anti-frost of high performance containing ground granulated blast furnace slag (GGBFS) under cold marine environment. Some comparison studies were conducted on plain concrete by rapid freeze-thaw cycle test. During the rapid freeze-thaw cycle test, the mass loss and relative elastic modulus were measured regularly at the prescribed conditioning ages. The development of microstructure in concrete was analyzed through scanning electron microscopy (SEM) and X-ray diffraction (XRD). The rapid freeze-thaw cycle test results show that the plain concrete was destroyed severely at 150 freeze-thaw cycles. After 225 freeze-thaw cycles, the mass loss and the relative dynamic modulus of elasticity of GGBFS concrete decrease 1.3% and 26.11%, respectively, that indicates that GGBFS significantly improve the anti-frost performance of concrete; The addition of GGBFS can accelerate the cement hydration reaction, promote more Ca (OH)2 crystals shift to C-S-H gel and help to increase the density of the micro-structure of concrete, which can prevent the formation of micro-cracks and suppress the propagation of cracks and thus effectively improve the durability of concrete. KEY WORDS: GGBFS; freeze-thaw durability; microstructure; scanning electron microscopy; X-ray diffraction.

scholarly journals CHEMICAL-MINERАLOGICAL CHARACTERIZATION OF BAUXITES FROM DIFFERENT DEPOSITS

2014 ◽  
Vol 5 (1) ◽  
Author(s):  
Gordana Оstojić ◽  
Dragica Lazić ◽  
Branko Škundrić ◽  
Jelena Penavin Škundrić ◽  
Slavica Sladojević ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Raw Materials ◽  
Mineralogical Composition ◽  
Chemical Characteristics ◽  
X Ray Diffraction ◽  
X Ray ◽  
Scanning Electron

From the aspect of their chemical and mineralogical composition, bauxites are very complex multicomponent raw materials. The paper presents the characterization of bauxite from several different deposits: Brazil, Milići, Čitluk and Kosovo. Chemical characteristics were determined by a combination of different analytical methods: gravimetry, potentiometric titration, atomic absorption spectroscopy (AAS) and UV-VIS spectrophotometry. Mineralogical composition was determined using X-ray diffraction and thermal analysis methods. Chemical and structural characterization is complemented by the results of scanning electron microscopy with EDX analysis. The information obtained was used for the assessment of the quality of investigated bauxites from the aspect of their application in the production of alumina.

scholarly journals Effects of different Sn contents on formation of Ti2SnC by self-propagating high-temperature synthesis method in Ti-Sn-C and Ti-Sn-C-TiC systems

2014 ◽  
Vol 32 (4) ◽  
pp. 696-701 ◽  
Author(s):  
Hong-Yan Sun ◽  
Xin Kong ◽  
Wei Sen ◽  
Zhong-Zhou Yi ◽  
Bao-Sen Wang ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Raw Materials ◽  
Synthesis Method ◽  
Combustion Products ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Temperature Synthesis ◽  
X Ray ◽  
High Temperature Synthesis ◽  
Scanning Electron

AbstractEffect of different Sn contents on combustion synthesis of Ti2SnC was studied using elemental Ti, Sn, C and TiC powders as raw materials in the Ti-Sn-C and Ti-Sn-C-TiC system, in which the molar ratio of Ti/C was set as 2:1. The reaction mechanism for the formation of Ti2SnC was also investigated. The results showed that the amount of Ti2SnC in combustion products firstly increased with increasing of Sn content (0.6 to 0.8 mol), and then decreased with further increasing of Sn content (1.0 to 1.2 mol). Upon addition of 15 % TiC instead of Ti and C, the optimum addition of Sn decreased to 0.7 mol and a higher purity of Ti2SnC was obtained. The Ti2SnC powders were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD).

Sign in / Sign up

Export Citation Format

Share Document