scholarly journals Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 465
Author(s):  
Roberto Scaffaro ◽  
Maria Clara Citarrella ◽  
Emmanuel Fortunato Gulino ◽  
Marco Morreale
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Fused Deposition Modeling ◽  
Young's Modulus ◽  
Compression Molding ◽  
Green Composite ◽  
Fused Deposition ◽  
Hedysarum Coronarium ◽  
Deposition Modeling ◽  
Fibers Orientation

In this work, an innovative green composite was produced by adding Hedysarum coronarium (HC) flour to a starch-based biodegradable polymer (Mater-Bi®, MB). The flour was obtained by grinding together stems, leaves and flowers and subsequently sieving it, selecting a fraction from 75 μm to 300 μm. Four formulations have been produced by compression molding (CM) and fused deposition modeling (FDM) by adding 5%, 10%, 15% and 20% of HC to MB. The influence of filler content on the processability was tested, and rheological, morphological and mechanical properties of composites were also assessed. Through CM, it was possible to obtain easily homogeneous samples with all filler amounts. Concerning FDM, 5% and 10% HC-filled composites proved also easily printable. Mechanical results showed filler effectively acted as reinforcement: Young’s modulus and tensile strengths of the composites increased from 74.3 MPa to 236 MPa and from 18.6 MPa to 33.4 MPa, respectively, when 20% of HC was added to the pure matrix. FDM samples, moreover, showed higher mechanical properties if compared with CM ones due to rectilinear infill and fibers orientation. In fact, regarding the 10% HC composites, Young’s modulus of the CM and FDM ones displayed a relative increment of 176% and 224%, respectively.

Characterization of Mechanical Property of PLA-ABS Functionally Graded Material Fabricated by Fused Deposition Modeling

2021 ◽  
Author(s):  
Ziyi Su ◽  
Kazuaki Inaba ◽  
Amit Karmakar ◽  
Apurba Das
Keyword(s):  
Tensile Test ◽  
Young’S Modulus ◽  
Natural Frequency ◽  
Functionally Graded Material ◽  
Fused Deposition Modeling ◽  
Young's Modulus ◽  
Functionally Graded ◽  
Fused Deposition ◽  
Graded Material ◽  
Deposition Modeling

Abstract Application of functionally graded materials (FGMs) in energy, aviation and nuclear industries has increased since the last decade due to potential reduction of in-plane and transverse through-the-thickness stresses, enhanced residual stress distribution, superior thermal properties, free from delamination, and reduced stress intensity factors. FGMs are categorized as an advanced class of composite materials where the two constituent materials are graded along the thickness direction. Absence of sharp change in material property in the interface layer eliminates the problem of delamination and debonding, which is a major concern for traditional composite material. In this work, PLA-ABS functionally graded material is manufactured using additive manufacturing techniques through fused deposition modeling (FDM) using Y-type extruder. X-ray computed tomography test is conducted to see the air void (generated during printing) distribution in the printed FGM. Tensile test (as per ISO-527standrad) is conducted to evaluate the Young’s Modulus of additive manufactured FGMs. Three different measuring positions are considered in the FGM specimens to check the effect of property change along the grading direction. Tensile test results of PLA-ABS FGM are compared with their individual constituents (ABS and PLA). Further, flexural vibration test is conducted to evaluate the natural frequency of printed FGM beam. Experimentally determined mechanical and dynamic characteristics in terms effective Young’s Modulus and natural frequency are analyzed and discussed.

Optimization of fused deposition modeling process parameters using the Taguchi method to improve the tensile properties of 3D-printed polyether ether ketone

2021 ◽  
pp. 146442072110175
Author(s):  
Timoumi Mohamed ◽  
Najoua Barhoumi ◽  
Khalid Lamnawar ◽  
Abderrahim Maazouz ◽  
Amna Znaidi
Keyword(s):  
Tensile Properties ◽  
Young’S Modulus ◽  
Layer Thickness ◽  
Process Parameters ◽  
Fused Deposition Modeling ◽  
Young's Modulus ◽  
Fused Deposition ◽  
Polyether Ether Ketone ◽  
Deposition Modeling ◽  
Ether Ketone

The interesting mechanical properties of polyether ether ketone give the material a place among the foremost competitors when it comes to replacing metal. Fused deposition modeling has been recognized as an alternative method to process polyether ether ketone parts. In this study, the effect of different process parameters such as nozzle, bed, and radiant temperatures as well as printing speed and layer thickness on the tensile properties of three-dimensional printed polyether ether ketone was investigated. The optimization of the tensile properties of PEEK were studied by performing a reduced number of experiments, using the experimental design method based on the Taguchi approach which limits the number of experiments to 8 instead of 32. Results showed that a decent Young’s modulus was found by setting the nozzle temperature, print speed, and bed temperatures to their high levels and by setting the layer thickness and radiant temperature to their low level. Using these parameters, a Young’s modulus of 3.5 GPa was obtained, which represents 87.5% of the value indicated in the technical sheet. With these settings, we also found a tensile strength of 45.5 MPa, which corresponds to 46.4% of the value given by the studied polyether ether ketone material. A scanning electron microscopic investigation of the porosity and interlayer adhesion, confirmed that a higher bed temperature also tended to promote adhesion between layers.

scholarly journals A Comparative Analysis of Selected Methods for Determining Young’s Modulus in Polylactic Acid Samples Manufactured with the FDM Method

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 149
Author(s):  
Bartosz Pszczółkowski ◽  
Konrad W. Nowak ◽  
Wojciech Rejmer ◽  
Mirosław Bramowicz ◽  
Łukasz Dzadz ◽  
...  
Keyword(s):  
Young’S Modulus ◽  
Polylactic Acid ◽  
Fused Deposition Modeling ◽  
Young's Modulus ◽  
Acrylonitrile Butadiene Styrene ◽  
Tensile Tests ◽  
Fused Filament Fabrication ◽  
Fused Deposition ◽  
Static Tensile ◽  
Deposition Modeling

The objective of this study was to compare three methods for determining the Young’s modulus of polylactic acid (PLA) and acrylonitrile-butadiene-styrene (ABS) samples. The samples were manufactured viathe fused filament fabrication/fused deposition modeling (FFF/FDM) 3D printing technique. Samples for analysis were obtained at processing temperatures of 180 °C to 230 °C. Measurements were performed with the use of two nondestructive techniques: the impulse excitation technique (IET) and the ultrasonic (US) method. The results were compared with values obtained in static tensile tests (STT), which ranged from 2.06 ± 0.03 to 2.15 ± 0.05 GPa. Similar changes in Young’s modulus were observed in response to the processing temperatures of the compared methods. The values generated by the US method were closer to the results of the STT, but still diverged considerably, and the error exceeded 10% in all cases. Based on the present findings, it might be concluded that the results of destructive and nondestructive tests differ by approximately 1 GPa.

Synthesis and properties of modified PBT for FDM

2017 ◽  
Vol 23 (4) ◽  
pp. 804-810 ◽  
Author(s):  
Shiqing Cao ◽  
Dandan Yu ◽  
Weilan Xue ◽  
Zuoxiang Zeng ◽  
Wanyu Zhu
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Fused Deposition Modeling ◽  
Complex Structure ◽  
Three Dimensional ◽  
Sebacic Acid ◽  
Wire Drawing ◽  
Content Type ◽  
Fused Deposition ◽  
Deposition Modeling

Purpose The purpose of this paper is to prepare a new modified polybutylene terephalate (MPBT) for fused deposition modeling (FDM) to increase the variety of materials compatible with printing. And the printing materials can be used to print components with a complex structure and functional mechanical parts. Design/methodology/approach The MPBT, poly(butylene terephalate-co-isophthalate-co-sebacate) (PBTIS), was prepared for FDM by direct esterification and subsequent polycondensation using terephthalic acid (PTA), isophthalic acid (PIA), sebacic acid (SA) and 1,4-butanediol (BDO). The effects of the content of PIA (20-40 mol%) on the mechanical properties of PBTIS were investigated when the mole per cent of SA (αSA) is zero. The effects of αSA (0-7mol%) on the thermal, rheological and mechanical properties of PBTIS were investigated at nPTA/nPIA = 7/3. A desktop wire drawing and extruding machine was used to fabricate the filaments, whose printability and anisotropy were tested by three-dimensional (3D) printing experiments. Findings A candidate content of PIA introducing into PBT was obtained to be about 30 per cent, and the Izod notched impact strength of PBTIS increased with the increase of αSA. The results showed that the PBTIS (nPTA/nPIA = 7/3, αSA = 3-5mol%) is suitable for FDM. Originality/value New printing materials with good Izod notched impact strength were obtained by introducing PIA and SA (nPTA/nPIA = 7/3, αSA = 3-5 mol%) into PBT and their anisotropy are better than that of ABS.

Assessing the effect of FDM processing parameters on mechanical properties of PLA parts using Taguchi method

2021 ◽  
pp. 089270572110530
Author(s):  
Nagarjuna Maguluri ◽  
Gamini Suresh ◽  
K Venkata Rao
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Fused Deposition Modeling ◽  
Fracture Strain ◽  
Processing Parameters ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
Nozzle Temperature ◽  
Experimental Runs ◽  
Printing Speed

Fused deposition modeling (FDM) is a fast-expanding additive manufacturing technique for fabricating various polymer components in engineering and medical applications. The mechanical properties of components printed with the FDM method are influenced by several process parameters. In the current work, the influence of nozzle temperature, infill density, and printing speed on the tensile properties of specimens printed using polylactic acid (PLA) filament was investigated. With an objective to achieve better tensile properties including elastic modulus, tensile strength, and fracture strain; Taguchi L8 array has been used for framing experimental runs, and eight experiments were conducted. The results demonstrate that the nozzle temperature significantly influences the tensile properties of the FDM printed PLA products followed by infill density. The optimum processing parameters were determined for the FDM printed PLA material at a nozzle temperature of 220°C, infill density of 100%, and printing speed of 20 mm/s.

scholarly journals EFFECT OF EXTRUSION PROCESS PARAMETERS ON MECHANICAL PROPERTIES OF 3D PRINTED PLA PRODUCT

2021 ◽  
Vol 6 (2) ◽  
pp. 119
Author(s):  
Nanang Ali Sutisna ◽  
Rakha Amrillah Fattah
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
Fused Deposition Modeling ◽  
Extrusion Process ◽  
Experimental Procedure ◽  
Fused Deposition ◽  
Novel Approach ◽  
Deposition Modeling ◽  
3D Printed ◽  
3D Digital Models

The method of producing items through synchronously depositing material level by level, based on 3D digital models, is named Additive Manufacturing (AM) or 3D-printing. Amongs many AM methods, the Fused Deposition Modeling (FDM) technique along with PLA (Polylactic acid) material is commonly used in additive manufacturing. Until now, the mechanical properties of the AM components could not be calculated or estimated until they've been assembled and checked. In this work, a novel approach is suggested as to how the extrusion process affects the mechanical properties of the printed component to obtain how the parts can be manufactured or printed to achieve improved mechanical properties. This methodology is based on an experimental procedure in which the combination of parameters to achieve an optimal from a manufacturing experiment and its value can be determined, the results obtained show the effect of the extrusion process affects the mechanical properties.

scholarly journals Preliminary Study on Mechanical Properties of 3D Printed Multimaterials ABS/PC Parts: Effect of Printing Parameters

2021 ◽  
Vol 32 (2) ◽  
pp. 87-104
Author(s):  
Pui-Voon Yap ◽  
Ming-Yeng Chan ◽  
Seong-Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flexural Modulus ◽  
Nozzle Diameter ◽  
Fused Deposition ◽  
Printing Parameters ◽  
Printing Speed

This research work highlights the mechanical properties of multi-material by fused deposition modelling (FDM). The specimens for tensile and flexural test have been printed using polycarbonate (PC) material at different combinations of printing parameters. The effects of varied printing speed, infill density and nozzle diameter on the mechanical properties of specimens have been investigated. Multi-material specimens were fabricated with acrylonitrile butadiene styrene (ABS) as the base material and PC as the reinforced material at the optimum printing parameter combination. The specimens were then subjected to mechanical testing to observe their tensile strength, Young’s modulus, percentage elongation, flexural strength and flexural modulus. The outcome of replacing half of ABS with PC to create a multi-material part has been examined. As demonstrated by the results, the optimum combination of printing parameters is 60 mm/s printing speed, 15% infill density and 0.8 mm nozzle diameter. The combination of ABS and PC materials as reinforcing material has improved the tensile strength (by 38.46%), Young’s modulus (by 23.40%), flexural strength (by 23.90%) and flexural modulus (by 37.33%) while reducing the ductility by 14.31% as compared to pure ABS. The results have been supported by data and graphs of the analysed specimens.

Sign in / Sign up

Export Citation Format

Share Document