Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling

In this work, an innovative green composite was produced by adding Hedysarum coronarium (HC) flour to a starch-based biodegradable polymer (Mater-Bi®, MB). The flour was obtained by grinding together stems, leaves and flowers and subsequently sieving it, selecting a fraction from 75 μm to 300 μm. Four formulations have been produced by compression molding (CM) and fused deposition modeling (FDM) by adding 5%, 10%, 15% and 20% of HC to MB. The influence of filler content on the processability was tested, and rheological, morphological and mechanical properties of composites were also assessed. Through CM, it was possible to obtain easily homogeneous samples with all filler amounts. Concerning FDM, 5% and 10% HC-filled composites proved also easily printable. Mechanical results showed filler effectively acted as reinforcement: Young’s modulus and tensile strengths of the composites increased from 74.3 MPa to 236 MPa and from 18.6 MPa to 33.4 MPa, respectively, when 20% of HC was added to the pure matrix. FDM samples, moreover, showed higher mechanical properties if compared with CM ones due to rectilinear infill and fibers orientation. In fact, regarding the 10% HC composites, Young’s modulus of the CM and FDM ones displayed a relative increment of 176% and 224%, respectively.

A local green composite study: the effect of edible oil on the morphological and mechanical properties of PBS/bentonite composite

Composites of a biodegradable thermoplastic aliphatic polyester, polybutylene succinate (PBS), with bentonite were investigated for morphological and mechanical properties. The bentonite was modified with soybean oil (SBO) and lard oil (LO) (2:98 clay:oil % by weight) by mechanical stirring and ultrasonication. The PBS/modified bentonite composite was prepared by using an internal mixer and processed by compression molding. Under bentonite modification conditions, XRD and SEM showed that the bentonite layers were broken into small layers, and the d-spacing between the layers was increased by edible oil molecules. A small plate like structure of modified bentonite composite was observed by SEM micrograph, which revealed short and long layer silicate structure non-directionally throughout the matrix phase. The mechanical properties of PBS were reinforced by this structure. The tensile modulus and elongation at break seem to depend on its directional bentonite. Interestingly, considerable improvement in impact strength was observed at over 2 wt% of clay. The impact strengths of PBS, PBS/modified BTN with SBO composite, and PBS/modified BTN with LO composite were increased from 1 to 1.5 and 2 kJ/m2, respectively. Comparatively, using LO modified bentonite had a better performance for increased interlayer and resulted in higher impact strength of the composite than that of SBO composite. The results demonstrated that PBS/modified bentonite using edible oil could be a potential alternative low cost, eco-friendly material with superior impact properties useful for further applications.

Bacterial Cellulose: Production, Characterization and Application as Antimicrobial Agent

Bacterial cellulose (BC) is recognized as a multifaceted, versatile biomaterial with abundant applications. Groups of microorganisms such as bacteria are accountable for BC synthesis through static or agitated fermentation processes in the presence of competent media. In comparison to static cultivation, agitated cultivation provides the maximum yield of the BC. A pure cellulose BC can positively interact with hydrophilic or hydrophobic biopolymers while being used in the biomedical domain. From the last two decades, the reinforcement of biopolymer-based biocomposites and its applicability with BC have increased in the research field. The harmony of hydrophobic biopolymers can be reduced due to the high moisture content of BC in comparison to hydrophilic biopolymers. Mechanical properties are the important parameters not only in producing green composite but also in dealing with tissue engineering, medical implants, and biofilm. The wide requisition of BC in medical as well as industrial fields has warranted the scaling up of the production of BC with added economy. This review provides a detailed overview of the production and properties of BC and several parameters affecting the production of BC and its biocomposites, elucidating their antimicrobial and antibiofilm efficacy with an insight to highlight their therapeutic potential.

Experimental study on two-body and three-body abrasive wear behaviour of jute-natural rubber flexible green composite

The use of laboratory testing has become more significant to assess abrasion resistance in flexible reinforcement of armour and car structural components. In this study, compliant composite with constituents as woven jute fabric and natural rubber (NR) encapsulated in an NR-based B stage cured prepreg were tested for wear due to abrasion under two- and three-body conditions. Flexible composites are fabricated in three different configurations namely Jute/Rubber/Jute (JRJ), Jute/Rubber/Rubber/Jute (JRRJ) and Jute/Rubber/Jute/Rubber/Jute (JRJRJ). The present study makes use of abrasive paper with a grit size of 60 and silica sand with size 250 µm as the abrasive medium for two- and three-body abrasion tests respectively and the specific rate of wear is calculated. Though the wear trend of the composites follows a similar pattern in the case of two- and three-body wear, the mechanisms governing the wear are found to be different. The morphology of the worn surface is studied with the aid of a scanning electron microscope.