scholarly journals Effects of Leading-Edge Modification in Damaged Rotor Blades on Aerodynamic Characteristics of High-Pressure Gas Turbine

Mathematics ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 2191
Author(s):  
Thanh Dam Mai ◽  
Jaiyoung Ryu
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Leading Edge ◽  
Combined Cycle ◽  
Rotor Blades ◽  
Sudden Increase ◽  
Damage Location

The flow and heat-transfer attributes of gas turbines significantly affect the output power and overall efficiency of combined-cycle power plants. However, the high-temperature and high-pressure environment can damage the turbine blade surface, potentially resulting in failure of the power plant. Because of the elevated cost of replacing turbine blades, damaged blades are usually repaired through modification of their profile around the damage location. This study compared the effects of modifying various damage locations along the leading edge of a rotor blade on the performance of the gas turbine. We simulated five rotor blades—an undamaged blade (reference) and blades damaged on the pressure and suction sides at the top and middle. The Reynolds-averaged Navier–Stokes equation was used to investigate the compressible flow in a GE-E3 gas turbine. The results showed that the temperatures of the blade and vane surfaces with damages at the middle increased by about 0.8% and 1.2%, respectively. This causes a sudden increase in the heat transfer and thermal stress on the blade and vane surfaces, especially around the damage location. Compared with the reference case, modifications to the top-damaged blades produced a slight increase in efficiency about 2.6%, while those to the middle-damaged blades reduced the efficiency by approximately 2.2%.

scholarly journals Effects of Damaged Rotor Blades on the Aerodynamic Behavior and Heat-Transfer Characteristics of High-Pressure Gas Turbines

Mathematics ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 627
Author(s):  
Thanh Dam Mai ◽  
Jaiyoung Ryu
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Rotor Blade ◽  
High Speed ◽  
Power Plants ◽  
Thermal Stresses ◽  
Turbine Blades ◽  
Combined Cycle

Gas turbines are critical components of combined-cycle power plants because they influence the power output and overall efficiency. However, gas-turbine blades are susceptible to damage when operated under high-pressure, high-temperature conditions. This reduces gas-turbine performance and increases the probability of power-plant failure. This study compares the effects of rotor-blade damage at different locations on their aerodynamic behavior and heat-transfer properties. To this end, we considered five cases: a reference case involving a normal rotor blade and one case each of damage occurring on the pressure and suction sides of the blades’ near-tip and midspan sections. We used the Reynolds-averaged Navier-Stokes equation coupled with the k − ω SST γ turbulence model to solve the problem of high-speed, high-pressure compressible flow through the GE-E3 gas-turbine model. The results reveal that the rotor-blade damage increases the heat-transfer coefficients of the blade and vane surfaces by approximately 1% and 0.5%, respectively. This, in turn, increases their thermal stresses, especially near the rotor-blade tip and around damaged locations. The four damaged-blade cases reveal an increase in the aerodynamic force acting on the blade/vane surfaces. This increases the mechanical stress on and reduces the fatigue life of the blade/vane components.

Research on Heat-Transfer and Cooling Performance of Gas Turbine Endwall

2017 ◽  
Author(s):  
Kazuto Kakio ◽  
Y. Kawata
Keyword(s):  
Heat Transfer ◽  
Pressure Gradient ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Power Plants ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Cooling Performance

Recently, the number of gas turbine combined cycle plants is rapidly increasing in substitution of nuclear power plants. The turbine inlet temperature (TIT) is being constantly increased in order to achieve higher efficiency. Therefore, the improvement of the cooling technology for high temperature gas turbine blades is one of the most important issue to be solved. In a gas turbine, the main flow impinging at the leading edge of the turbine blade generates a so called horseshoe vortex by the interaction of its boundary layer and generated pressure gradient at the leading edge. The pressure surface leg of this horseshoe vortex crosses the passage and reaches the blade suction surface, driven by the pressure gradient existing between two consecutive blades. In addition, this pressure gradient generates a crossflow along the endwall. This all results into a very complex flow field in proximity of the endwall. For this reason, burnouts tend to occur at a specific position in the vicinity of the leading edge. In this research, a methodology to cool the endwall of the turbine blade by means of film cooling jets from the blade surface is proposed. The cooling performance and heat transfer coefficient distribution is investigated using the transient thermography method. CFD analysis is also conducted to know the phenomena occurring at the end wall and calculate the heat transfer distribution.

A Thermodynamic Analysis of Different Options to Break 60% Electric Efficiency in Combined Cycle Power Plants

2004 ◽  
Vol 126 (4) ◽  
pp. 770-785 ◽  
Author(s):  
Paolo Chiesa ◽  
Ennio Macchi
Keyword(s):  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Gas Turbines ◽  
Power Plants ◽  
Closed Loop ◽  
Open Loop ◽  
Combined Cycle ◽  
Rotor Blades ◽  
Air Cooling ◽  
Large Size

All major manufacturers of large size gas turbines are developing new techniques aimed at achieving net electric efficiency higher than 60% in combined cycle applications. An essential factor for this goal is the effective cooling of the hottest rows of the gas turbine. The present work investigates three different approaches to this problem: (i) the most conventional open-loop air cooling; (ii) the closed-loop steam cooling for vanes and rotor blades; (iii) the use of two independent closed-loop circuits: steam for stator vanes and air for rotor blades. Reference is made uniquely to large size, single shaft units and performance is estimated through an updated release of the thermodynamic code GS, developed at the Energy Department of Politecnico di Milano. A detailed presentation of the calculation method is given in the paper. Although many aspects (such as reliability, capital cost, environmental issues) which can affect gas turbine design were neglected, thermodynamic analysis showed that efficiency higher than 61% can be achieved in the frame of current, available technology.

A Thermodynamic Analysis of Different Options to Break 60% Electric Efficiency in Combined Cycle Power Plants

2002 ◽  
Author(s):  
Paolo Chiesa ◽  
Ennio Macchi
Keyword(s):  
Gas Turbine ◽  
Thermodynamic Analysis ◽  
Gas Turbines ◽  
Power Plants ◽  
Closed Loop ◽  
Open Loop ◽  
Combined Cycle ◽  
Rotor Blades ◽  
Air Cooling ◽  
Large Size

All major manufacturers of large size gas turbines are developing new techniques aimed at achieving net electric efficiency higher than 60% in combined cycle applications. An essential factor for this goal is the effective cooling of the hottest rows of the gas turbine. The present work investigates three different approaches to this problem: (i) the most conventional open-loop air cooling; (ii) the closed-loop steam cooling for vanes and rotor blades; (iii) the use of two independent closed-loop circuits: steam for stator vanes and air for rotor blades. Reference is made uniquely to large size, single shaft units and performance is estimated through an updated release of the thermodynamic code GS, developed at the Energy Dept. of Politecnico di Milano. A detailed presentation of the calculation method is given in the paper. Although many aspects (such as reliability, capital cost, environmental issues) which can affect gas turbine design were neglected, thermodynamic analysis showed that efficiency higher than 61% can be achieved in the frame of current, available technology.

Modified Rankine HRSG Beats Triple-Pressure System

1996 ◽  
Author(s):  
Peter Eisenkolb ◽  
Martin Pogoreutz ◽  
Hermann Halozan
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Heat Recovery ◽  
Power Plants ◽  
Fossil Fuels ◽  
Combined Cycle ◽  
Exhaust Gas ◽  
Pressure System ◽  
Exergy Losses

Gas-fired combined cycle power plants (CCP) are presently the most efficient systems for producing electricity with fossil fuels. Gas turbines have been and are being improved remarkably during the last years; presently they achieve efficiencies of more than 38% and gas turbine outlet temperatures of up to 610°C. These high outlet temperatures require modifications and improvements of heat recovery steam generators (HRSG). Presently dual pressure HRSGs are most commonly used in combined cycle power stations. The next step seems to be the triple-pressure HRSG to be able to utilise the high gas turbine outlet temperatures efficiently and to reduce exergy losses caused by the heat transfer between exhaust gas and the steam cycle. However, such triple-pressure systems are complicated considering parallel tube bundles as well as start up operation and load changes. For that reason an attempt has been made to replace such multiple pressure systems by a modified Rankine cycle with only a single-pressure level. In the case of the same total heat transfer surfaces this innovative single-pressure system achieves approximately the same efficiency as the triple-pressure system. By optimising the heat recovery from the exhaust gas to the steam/water cycle, i.e. minimising exergy losses, the stack temperature is much higher. Increasing the heat transfer surfaces means a decrease of the stack temperature and a further improvement of the overall CCP-efficiency. Therefore one has to be aware that the proposed system offers advantages not only in the case of a foreseeable increase of gas turbine outlet temperatures but also for presently available gas turbines. Using existing highly efficient gas turbines and subcritical steam conditions, power plants with this proposed Eisenkolb Single Pressure (ESP_CCP) heat recovery steam generator achieve thermal efficiencies of about 58.7% (LHV).

Application of Ultra-Low NOx Combustor to the MHPS Existing Gas Turbine

2021 ◽  
Author(s):  
Takashi Nishiumi ◽  
Hirofumi Ohara ◽  
Kotaro Miyauchi ◽  
Sosuke Nakamura ◽  
Toshishige Ai ◽  
...  
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Operational Experience ◽  
Emission Rates ◽  
Gas Temperature ◽  
Design Development ◽  
And Control

Abstract In recent years, MHPS achieved a NET M501J gas turbine combined cycle (GTCC) efficiency in excess of 62% operating at 1,600°C, while maintaining NOx under 25ppm. Taking advantage of our gas turbine combustion design, development and operational experience, retrofits of earlier generation gas turbines have been successfully applied and will be described in this paper. One example of the latest J-Series technologies, a conventional pilot nozzle was changed to a premix type pilot nozzle for low emission. The technology was retrofitted to the existing F-Series gas turbines, which resulted in emission rates of lower than 9ppm NOx(15%O2) while maintaining the same Turbine Inlet Temperature (TIT: Average Gas Temperature at the exit of the transition piece). After performing retrofitting design, high pressure rig tests, the field test prior to commercial operation was conducted on January 2019. This paper describes the Ultra-Low NOx combustor design features, retrofit design, high pressure rig test and verification test results of the upgraded M501F gas turbine. In addition, it describes another upgrade of turbine to improve efficiency and of combustion control system to achieve low emissions. Furthermore it describes the trouble-free upgrade of seven (7) units, which was completed by utilizing MHPS integration capabilities, including handling all the design, construction and service work of the main equipment, plant and control systems.

Part Load Conditions of Complex Cycle Power Plants With Intercooled Gas Turbine

1996 ◽  
Author(s):  
A. Peretto
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Working Conditions ◽  
Power Plants ◽  
Pressure Level ◽  
Combined Cycle ◽  
Brayton Cycle ◽  
Part Load ◽  
High Pressure Compressor ◽  
Pressure Compressor

The present paper evaluates the behavior, in design and part load working conditions, of a complex gas turbine cycle with multiple intercooled compression, and the optional preheating of the air at the high pressure compressor outlet by means of the gas turbine outlet hot gas. The results are then compared with those obtained by a Brayton cycle gas turbine, with or without preheating of the air at the high pressure compressor outlet. Subsequently, the performance of complex combined cycles, with intercooled gas turbine as topper and one, two or three pressure level steam cycle as bottomer, in design and part load working conditions is also evaluated. The performance of these complex combined plants is then compared with that obtained by a Brayton cycle gas turbine as topper and one, two or three pressure level steam cycle as bottomer. Part load working conditions are realized by varying either the inlet guide vane angle of the first compressor nozzles or the maximum temperature at the combustor outlet. The study shows that in part load working conditions obtained by varying IGV, the complex cycles, in the examined gas turbine or in the combined cycle power plants, give conversion efficiencies decidedly greater than those obtainable by varying combustor exit temperature. Furthermore it is found that these complex power plant efficiencies, in part load working conditions, are far greater than those obtained by the Brayton cycle gas turbine, or by combined cycle with Brayton cycle gas turbine as topper, if IGV adjustment is adopted. If power variation is obtained with combustor outlet temperature adjustment, the efficiencies of the combined power plants with complex or Brayton cycle gas turbines, are substantially the same, for the same relative power variation.

scholarly journals Advanced Aeroderivative Gas Turbines in Coal-Based High Performance Power Systems (HIPPS)

1998 ◽  
Author(s):  
F. L. Robson ◽  
D. J. Seery
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Power Plants ◽  
Performance Standards ◽  
Combined Cycle ◽  
Advanced Technology ◽  
Early 21St Century ◽  
Near Term

The Department of Energy’s Federal Energy Technology Center (FETC) is sponsoring the Combustion 2000 Program aimed at introducing clean and more efficient advanced technology coal-based power systems in the early 21st century. As part of this program, the United Technologies Research Center has assembled a seven member team to identify and develop the technology for a High Performance Power Systems (HIPPS) that will provide in the near term, 47% efficiency (HHV), and meet emission goals only one-tenth of current New Source Performance Standards for coal-fired power plants. In addition, the team is identifying advanced technologies that could result in HIPPS with efficiencies approaching 55% (HHV). The HIPPS is a combined cycle that uses a coal-fired High Temperature Advanced Furnace (HITAF) to preheat compressor discharge air in both convective and radiant heaters. The heated air is then sent to the gas turbine where additional fuel, either natural gas or distillate, is burned to raise the temperature to the levels of modern gas turbines. Steam is raised in the HITAF and in a Heat Recovery Steam Generator for the steam bottoming cycle. With state-of-the-art frame type gas turbines, the efficiency goal of 47% is met in a system with more than two-thirds of the heat input furnished by coal. By using advanced aeroderivative engine technology, HIPPS in combined-cycle and Humid Air Turbine (HAT) cycle configurations could result in efficiencies of over 50% and could approach 55%. The following paper contains descriptions of the HIPPS concept including the HITAF and heat exchangers, and of the various gas turbine configurations. Projections of HIPPS performance, emissions including significant reduction in greenhouse gases are given. Application of HIPPS to repowering is discussed.

On the Economics of the Use of Biomass Fuels in Gas Turbine Cycles: Gasification vs. Externally Firing

2004 ◽  
Author(s):  
Sandro Barros Ferreira ◽  
Pericles Pilidis
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Technological Development ◽  
Pilot Scale ◽  
Combined Cycle ◽  
Point Of View ◽  
Turbine Engine ◽  
Current Technology ◽  
Integrated Gasification

The use of biomass as gas turbine combined cycle fuels is broadly seen as one of the alternatives to diminish greenhouse gas emissions, mainly CO2, due to the efficiency delivered by such systems and the renewable characteristic of biomass itself. Integrated gasification cycles, BIGGT, are the current technology available; however the gasification system severely penalizes the power plant in terms of efficiency and demands modifications in the engine to accommodate the large fuel mass flow. This gives an opportunity to improvements in the current technologies and implementation of new ones. This paper intends to analyze new alternatives to the use of solid fuels in gas turbines, from the economical point of view, through the use of external combustion, EFGT, discussing its advantages and limitations over the current technology. The results show that both EFGT and BIGGT technologies are economically competitive with the current natural gas fired gas turbines. However, BIGGT power plants are still in pilot scale and the EFGT plants need further technological development. Thermodynamically speaking, the inherently recuperative characteristic of the EFGT gas turbine engine makes it well suited to the biomass market. The thermal efficiency of this cycle is higher than the BIGGT system. Furthermore, its fuel flexibility and negligible pre-treatmet is another advantage that makes it an interesting option for the Brazilian market.

Performance and Cost Analysis of Advanced Gas Turbine Cycles With Precombustion CO2 Capture

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Stéphanie Hoffmann ◽  
Michael Bartlett ◽  
Matthias Finkenrath ◽  
Andrei Evulet ◽  
Tord Peter Ursin
Keyword(s):  
High Pressure ◽  
Power Plant ◽  
Natural Gas ◽  
Gas Turbine ◽  
Co2 Capture ◽  
Gas Turbines ◽  
High Efficiency ◽  
Combined Cycle ◽  
Co2 Separation ◽  
The Cost

This paper presents the results of an evaluation of advanced combined cycle gas turbine plants with precombustion capture of CO2 from natural gas. In particular, the designs are carried out with the objectives of high efficiency, low capital cost, and low emissions of carbon dioxide to the atmosphere. The novel cycles introduced in this paper are comprised of a high-pressure syngas generation island, in which an air-blown partial oxidation reformer is used to generate syngas from natural gas, and a power island, in which a CO2-lean syngas is burnt in a large frame machine. In order to reduce the efficiency penalty of natural gas reforming, a significant effort is spent evaluating and optimizing alternatives to recover the heat released during the process. CO2 is removed from the shifted syngas using either CO2 absorbing solvents or a CO2 membrane. CO2 separation membranes, in particular, have the potential for considerable cost or energy savings compared with conventional solvent-based separation and benefit from the high-pressure level of the syngas generation island. A feasibility analysis and a cycle performance evaluation are carried out for large frame gas turbines such as the 9FB. Both short-term and long-term solutions have been investigated. An analysis of the cost of CO2 avoided is presented, including an evaluation of the cost of modifying the combined cycle due to CO2 separation. The paper describes a power plant reaching the performance targets of 50% net cycle efficiency and 80% CO2 capture, as well as the cost target of 30$ per ton of CO2 avoided (2006 Q1 basis). This paper indicates a development path to this power plant that minimizes technical risks by incremental implementation of new technology.

Sign in / Sign up

Export Citation Format

Share Document