scholarly journals Experimental Research and Numerical Simulation of Weld Repair with High Energy Spark Deposition Method

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 980 ◽  
Author(s):  
Yingjie Zhang ◽  
Kai Yang ◽  
Jianping Zhao
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Residual Stress ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
High Energy ◽  
Repair Welding ◽  
Repair Processes ◽  
Repair Technology ◽  
Surface Repair

For long-serviced pressure equipment that is under severe working conditions such as a high temperature, high pressure, and corrosion, the material properties and structure will be unavoidably damaged or degraded, especially cracks and other damages at key positions such as welded joints, which seriously threaten the safe operation of the equipment. In order to promote the sustainable development of industries such as the chemical and petrochemical industries, remanufacturing technology has emerged worldwide, and various surface repair processes have also rapidly developed. As an important branch of surface repair technology, the high energy spark deposition (HESD) process is a new pulse cold welding repair technology developed from electro-spark deposition, which combines the advantages of multiple surface repair processes. The HESD process has the characteristics of a smaller heat affected zone and lower welding residual stress. It is a new type of repair method that is worthy of popularization and application. The process has been initially applied in the fields of surface modification and die steel repair. In this paper, the application of the HESD process to the repair of welded joints was introduced, the mechanical properties of the joints and the residual stress distribution after welding were analyzed, and the feasibility of HESD as a repair welding method for pressure structures was discussed. First, a numerical simulation of the temperature and stress field of HESD was proposed by using ABAQUS and the related subprograms, and the validity of the simulation results was verified by the residual stress test with the indentation strain method. Due to the precise control of the heat and pulse discharge working mode, the heat-affected zone and deformation caused by the HESD were extremely small, and the residual stress that was generated was low and only concentrated on the repair welding seam. Second, according to the numerical simulation and the test results of the mechanical properties of the welded joint, the optimal repair welding process parameters were obtained through the orthogonal experiment: peak current 45 A, pulse width 90 ms, and output voltage 10 V.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

2021 ◽  
pp. 2150175
Author(s):  
Tao Mo ◽  
Jingqing Chen ◽  
Pengju Zhang ◽  
Wenqian Bai ◽  
Xiao Mu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Compressive Stress ◽  
Welded Joints ◽  
Welding Process ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
304 Stainless Steel ◽  
Residual Tensile Stress ◽  
Ultrasonic Impact Treatment

Ultrasonic impact treatment (UIT) is an effective method that has been widely applied in welding structure to improve the fatigue properties of materials. It combines mechanical impact and ultrasonic vibration to produce plastic deformation on the weld joints surface, which introduces beneficial compressive residual stress distribution. To evaluate the effect of UIT technology on alleviating the residual stress of welded joints, a novel numerical analysis method based on the inherent strain theory is proposed to simulate the stress superposition of welding and subsequent UIT process of 304 stainless steel. Meanwhile, the experiment according to the process was carried out to verify the simulation of residual stress values before and after UIT. By the results, optimization of UIT application could effectively reduce the residual stress concentration after welding process. Residual tensile stress of welded joints after UIT is transformed into residual compressive stress. UIT formed a residual compressive stress layer with a thickness of about 0.13 mm on the plate. The numerical simulation results are consistent with the experimental results. The work in this paper could provide theoretical basis and technical support for the reasonable evaluation of the ultrasonic impact on residual stress elimination and mechanical properties improvement of welded joints.

Characterization of Mechanical Properties and Residual Stress in API 5L X80 Steel Welded Joints

2017 ◽  
Vol 27 (1) ◽  
pp. 124-137 ◽  
Author(s):  
Amilton de Sousa Lins ◽  
Luís Felipe Guimarães de Souza ◽  
Maria Cindra Fonseca
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Welded Joints ◽  
X80 Steel

scholarly journals Effect of Residual Stress on the Mechanical Properties of FSW Joints with SUS409L

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Yeong-Seok Lim ◽  
Sang-Hyuk Kim ◽  
Kwang-Jin Lee
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Stress Measurement ◽  
Charpy Impact ◽  
Stir Zone ◽  
Hole Drilling ◽  
Friction Stir ◽  
Compressive Residual Stresses

This study was performed to investigate both the residual stress distribution and the effect of the residual stress formed at the welding region on the mechanical properties of the friction stir welded joints with 409L stainless steel sheets. Residual stress measurement with hole-drilling method; mechanical property evaluation including tensile test, Charpy impact test, and fatigue test; and microstructure observation were conducted. It has got no residual stresses to speak of at the center region of the stir zone because the stored stresses are released in the process of the dynamic recrystallization, while a small quantity of compressive residual stresses is formed at the surface region of the stir zone because of strong compression reaction by the tool shoulder. A considerable amount of compressive residual stresses is formed at the thermomechanical affected zone because of the synergy between the thermal expansion due to the heat conduction from the stir zone and mechanical compression by the tool. The formation of residual stresses shows a similar tendency between the advancing side and the retreating side. Both the mitigation of residual stress in the stir zone and the formation of compressive residual stress in the thermomechanical affected zone contribute to the improvement of the mechanical properties of the friction stir welded joints.

scholarly journals Shielded Metal Arc and Thermite Welding Effect to Residual Stress, Hardness and Crack of R54-Rail Weld Joint

2020 ◽  
Vol 55 (4) ◽  
Author(s):  
Yurianto ◽  
Gunawan Dwi Haryadi ◽  
Sri Nugroho ◽  
Sulardjaka ◽  
Susilo Adi Widayanto
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Base Metal ◽  
Heat Affected Zone ◽  
Welded Joints ◽  
Arc Welding ◽  
Welding Process ◽  
Shielded Metal Arc Welding ◽  
Metal Arc Welding ◽  
Crack Susceptibility

The heating and cooling at the end of the welding process can cause residual stresses that are permanent and remain in the welded joint. This study aims to evaluate the magnitude and direction of residual stresses on the base metal and heat-affected zone of rail joints welded by the manual shielded metal arc and thermite welding. This research supports the feasibility of welding for rail. The material used in this study is the R-54 rail type, and the procedure used two rail samples of one meter long each, welded using manual shielded metal arc welding and thermite welding. The base metal and heat-affected zone of the welded joints were scanned with neutron ray diffraction. The scan produces a spectrum pattern and reveals the direction of the residual stress along with it. We found the strain value contained in both types of welded joints by looking at the microstrain values, which we obtained using the Bragg equation. The results show that the magnitude and direction of the residual stress produced by manual shielded metal arc welding and thermite welding are not the same. Thermite welding produces lower residual stress (lower crack susceptibility) than manual shielded metal arc welding. The melt's freezing starts from the edge to the center of the weld to create random residual stresses. The residual stress results of both the manual shielded metal arc welding and thermite welding are still below the yield strength of the base metal.

Welding Residual Stress in HDPE Pipes: Measurement and Numerical Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Yu Sun ◽  
Yun-Fei Jia ◽  
Muhammad Haroon ◽  
Huan-sheng Lai ◽  
Wenchun Jiang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Distribution ◽  
Welded Joints ◽  
Residual Stress Distribution ◽  
Fusion Welding ◽  
Welding Residual Stress ◽  
Hole Drilling ◽  
Radial Depth ◽  
Hdpe Pipes

To understand the residual stress distribution in the welded joints of high density polyethylene (HDPE) pipes is essential to the assessment of its structural integrity. However, limited knowledge of their residual stress was available in this regard. In this paper, the hole-drilling strain-gage method was used to measure the residual stress in the welded seam of HDPE pipes, which was produced by the butt fusion welding technique. The finite element modeling using viscoelastic constitutive model with Prony series was carried out to determine the temperature field and corresponding stress field in the welding stages. The measured residual stress near the surface shows good consistency with the numerical results. It is shown that the residual stress in the hoop direction is much larger than those in the radial and axial directions. The effect of the pipe thickness on the residual stress distribution was also investigated by numerical simulation. The positions of the maximum tensile stress in the welded joints were found within the normalized depth region (the radial depth to the thickness) of 0.2 to 0.8.

scholarly journals Effects of Conventional and Severe Shot Peening on Residual Stress and Fatigue Strength of Steel AISI 1060 and Residual Stress Relaxation Due to Fatigue Loading: Experimental and Numerical Simulation

2020 ◽  
Author(s):  
Erfan Maleki ◽  
Gholam Hossein Farrahi ◽  
Kazem Reza Kashyzadeh ◽  
Okan Unal ◽  
Mario Gugaliano ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Relaxation ◽  
Shot Peening ◽  
Fatigue Behavior ◽  
Fatigue Loading ◽  
Experimental Investigations ◽  
Residual Stress Relaxation ◽  
Severe Shot Peening

Abstract This study investigates and compares the effects of different shot peening treatments including conventional and severe shot peening on microstructure, mechanical properties, fatigue behavior, and residual stress relaxation of AISI 1060 steel. Shot peening treatments were applied with two Almen intensities of 17 and 21 A and a wide ranges of coverage (100%–1500%). Various microstructural observations were carried out to analyze the evolution of microstructure. Microhardness, residual stress and surface roughness measurements and also axial fatigue test were performed. Moreover, the extent of the residual stress relaxation during cyclic loading was investigated by means of XRD measurements. Furthermore, numerical simulation of residual stress relaxation due to fatigue loading was carried out and validated against experimental investigations. The comparison indicated a good agreement for the surface residual stress relaxation up to 100 cycles. The experimental results indicated the efficiency of severe shot peening processes in obtaining nanostructured surface layer and achieving superior mechanical properties and fatigue behavior. Also, residual stress measurements revealed that stress relaxation started with a high rate at the initial stages of loading and gradually increased at higher number of cycles which was lower in the case of severely shot peened samples compared to the conventionally treated ones. Graphic Abstract

Sign in / Sign up

Export Citation Format

Share Document