scholarly journals Fracture Areas Quantitative Investigating of Bending–Torsion Fatigued Low-Alloy High-Strength Steel

Metals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1620
Author(s):  
Wojciech Macek
Keyword(s):  
Fatigue Life ◽  
Surface Topography ◽  
High Strength ◽  
Fatigue Loading ◽  
Fatigue Tests ◽  
Void Volume ◽  
Variation Method ◽  
Rupture Area ◽  
The Impact ◽  
Maximum Stresses

In this study, the impact of pseudo-random non-proportional bending-torsion fatigue loadings proportion on the fatigue life and the fracture surface topography was analyzed. Investigation was carried out for 24 specimens made of S355J2 steel with 11 different ratios of maximum stresses λ. For these cases, after the fatigue tests, the surface topography measurements were carried out using an optical profilometer, using the focus variation method. Three fracture zones were analyzed for each specimen: (1) total; (2) propagation; (3) rupture, taking into account the root average square height Sq and void volume Vv parameters. The results pointed that ratio of maximum stresses λ is the most influenced on volume surface parameters represented by void volume at a given height Vv, in the rupture area. A new fatigue loading parameter P was used, depending on fatigue life T and ratio of maximum stresses λ, which shows very good correlation in 4th degree type of fit, to void volume Vv parameter for the rupture area.

scholarly journals Fatigue Life Prediction of Machined Specimens with the Consideration of Surface Roughness

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5420
Author(s):  
Xiaochun Zhu ◽  
Zhurong Dong ◽  
Yachen Zhang ◽  
Zhengkun Cheng
Keyword(s):  
Surface Roughness ◽  
Fatigue Life ◽  
Surface Topography ◽  
High Strength Steels ◽  
High Strength ◽  
Fatigue Tests ◽  
Analytical Formulas ◽  
Fatigue Notch Factor ◽  
Underlying Mechanisms ◽  
Effect Of Surface

The fatigue strength and fatigue life of high-strength steels are greatly affected by their surface roughness. This study investigates the underlying mechanisms responsible for fatigue failure of the high-strength steel 42CrMo. Bending fatigue tests of stepped shafts with different levels of surface roughness were conducted to observe the fatigue live reduction affected by surface topography. Besides, the mechanical properties of 42CrMo and its strain–life relationship were established. Moreover, the analytical formulas to describe the stress concentration factor (SCF) and fatigue notch factor (FNF) induced by surface topography were introduced. To estimate the fatigue life of machined specimens with the consideration of surface roughness, the elastic portion of the total strain–life curve of the material was revised with the proposed analytical FNF imposed by surface topography. Comparisons between the estimated fatigue lives and experimentally obtained fatigue lives show that the effect of surface roughness on fatigue lives could be estimated effectively and conveniently by the proposed procedure.

A Study of Nozzles in Pressure Vessels under Pressure Fatigue Loading

1967 ◽  
Vol 182 (1) ◽  
pp. 657-684 ◽  
Author(s):  
J. Spence ◽  
W. B. Carlson
Keyword(s):  
Fatigue Life ◽  
Mild Steel ◽  
Pressure Vessel ◽  
Special Interest ◽  
Maximum Stress ◽  
Fatigue Loading ◽  
Fatigue Tests ◽  
Pressure Vessels ◽  
Full Size

Nozzles in cylindrical vessels have been of special interest to designers for some time and have offered a field of activity for many research workers. This paper presents some static and fatigue tests on five designs of full size pressure vessel nozzles manufactured in two materials. Supporting and other published work is reviewed showing that on the basis of the same maximum stress mild steel vessels give the same fatigue life as low alloy vessels. When compared on the basis of current codes it is shown that mild steel vessels may have five to ten times the fatigue life of low alloy vessels unless special precautions are taken.

Improving Fatigue Life of Riveted Joints by Rivet Hole Sizing

2014 ◽  
Vol 598 ◽  
pp. 141-146
Author(s):  
Adam Lipski ◽  
Zbigniew Lis
Keyword(s):  
Fatigue Life ◽  
Fold Increase ◽  
Fatigue Tests ◽  
Aviation Industry ◽  
Lap Joint ◽  
Riveted Joints ◽  
Riveting Process ◽  
The Difference ◽  
Structural Connection ◽  
The Impact

The aim of this paper is to assess the impact of the rivet hole sizing process on the fatigue life based on the example of the structural connections characteristic for riveted joints used in aviation industry. Test specimens reflected the structural connection consisting in a riveted lap joint of an airplane plating stiffened with a T-bar. Connected plates and the T-bar are made of D16CzATW aluminum alloy. 3 mm diameter oval head solid rivets for aviation-related purposes were made of PA24 aluminum. During fatigue tests, individual specimens with non-sized holes and with sized holes were subjected to uniaxial, one-sided, fixed-amplitude loading (R = 0). It can be concluded from the fatigue life comparison that introduction of an additional operation in the riveting process, i.e. the hole sizing, results in significant, about two-fold increase of the fatigue life of the riveted structural connection, even at slight sizing degree. The difference of the specimen damage nature was observed between specimens with sized and non-sized holes.

scholarly journals Multiaxial fatigue study on steel transversal attachments under constant amplitude proportional and non-proportional loadings

2018 ◽  
Vol 165 ◽  
pp. 16007
Author(s):  
Martin Garcia ◽  
Claudio A. Pereira Baptista ◽  
Alain Nussbaumer
Keyword(s):  
Fatigue Life ◽  
High Strength ◽  
Fatigue Tests ◽  
Multiaxial Fatigue ◽  
Life Assessment ◽  
Experimental Program ◽  
Proportional Loading ◽  
Load Carrying ◽  
Stress States ◽  
Experimental Values

In this study, the multiaxial fatigue strength of full-scale transversal attachment is assessed and compared to original experimental results and others found in the literature. Mild strength S235JR steel is used and an exploratory investigation on the use of high strength S690QL steel and the effect of non-proportional loading is presented. The study focuses on non-load carrying fillet welds as commonly used in bridge design and more generally between main girders and struts. The experimental program includes 33 uniaxial and multiaxial fatigue tests and was partially carried out on a new multiaxial setup that allows proportional and non-proportional tests in a typical welded detail. The fatigue life is then compared with estimations obtained from local approaches with the help of 3D finite element models. The multiaxial fatigue life assessment with some of the well-known local approaches is shown to be suited to the analysis under multiaxial stress states. The accuracy of each models and approaches is compared to the experimental values considering all the previously cited parameters.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

scholarly journals Experimental Investigation on the Effect of Shot Peening and Deep Rolling on the Fatigue Response of High Strength Fasteners

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1093 ◽  
Author(s):  
Reggiani
Keyword(s):  
Fatigue Life ◽  
Shot Peening ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Tests ◽  
Published Data ◽  
Deep Rolling ◽  
Beneficial Impact ◽  
The Impact ◽  
Fatigue Life Enhancement

Shot-peening and deep rolling are mechanical surface treatments that are commonly applied to enhance the fatigue performances of components, owing to their capacity to generate compressive residual stresses and induce work hardening. However, literature is still poor of published data concerning the application of these treatments to high strength steels fasteners, although these represent a class of components among the most widespread. In the present work, the impact of deep rolling and shot-peening performed in the underhead radius of two set of fasteners made of 36NiCrMo and 42CrMoV for fatigue life enhancement has been investigated. The experimental tests consisted of six combinations of shot-peening and deep rolling, including the non-treated state. Two test campaigns have been sequentially carried out with different process parameters and treatment sequences. The results always showed a beneficial impact of the deep rolling on fatigue, especially for the 42CrMoV steel. Conversely, the effect of the shot-peening strongly depended on the selected set of parameters, alternatively leading to an improvement or a worsening of the fatigue life in relation to the level of induced surface roughness.

High Cycle Fatigue Behavior of Recycled Additive Manufactured Electron Beam Melted Titanium Ti6Al4V

2020 ◽  
Author(s):  
Melody Mojib ◽  
Rishi Pahuja ◽  
M. Ramulu ◽  
Dwayne Arola
Keyword(s):  
Electron Beam ◽  
Fatigue Life ◽  
Rough Surface ◽  
High Cycle Fatigue ◽  
Fatigue Behavior ◽  
High Strength ◽  
Fatigue Tests ◽  
Cycle Fatigue ◽  
Initiation And Propagation ◽  
Powder Recycling

Abstract Metal Additive Manufacturing (AM) has become a popular method for producing complex and unique geometries, especially gaining traction in the aerospace and medical industries. With the increase in adoption of AM and the high cost of powder, it is critical to understand the effects of powder recycling on part performance to move towards material qualification and certification of affordable printed components. Due to the limitations of the Electron Beam Melting (EBM) process, current as-printed components are susceptible to failure at limits far below wrought metals and further understanding of the material properties and fatigue life is required. In this study, a high strength Titanium alloy, Ti-6Al-4V, is recycled over time and used to print fatigue specimens using the EBM process. Uniaxial High Cycle Fatigue tests have been performed on as-printed and polished cylindrical specimens and the locations of crack initiation and propagation have been determined through the use of a scanning electron microscope. This investigation has shown that the rough surface exterior is far more detrimental to performance life than the powder degradation occurring due to powder reuse. In addition, the effects of the rough surface exterior as a stress concentration is evaluated using the Arola-Ramulu. The following is a preliminary study of the effects powder recycling and surface treatments on EBM Ti-6Al4V fatigue life.

Fatigue Behavior of Impacted Plain-Weave Glass/Epoxy Composites under Tensile Fatigue Loading

2005 ◽  
Vol 297-300 ◽  
pp. 1291-1296 ◽  
Author(s):  
Ki Weon Kang ◽  
Jung Kyu Kim ◽  
Heung Seob Kim
Keyword(s):  
Fatigue Life ◽  
Impact Damage ◽  
Fatigue Behavior ◽  
Fatigue Loading ◽  
Epoxy Composites ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Damage Behavior ◽  
Plain Weave ◽  
The Impact

The goals of this paper are to identify the impact damage behavior of plain-weave E-glass/epoxy composites and predict the fatigue life of the composites with impact-induced damage under constant amplitude loading. To identify these behaviors, the low velocity impact and fatigue after impact tests are performed for glass/epoxy composites having two types of fiber orientations. The impact damage behavior is dependent on the fiber orientation of the composites. The fatigue life of the impacted composites can be identified through the prediction model, which was proposed on the carbon/epoxy laminates by authors regardless of fiber orientations.

scholarly journals Damage Characterization of Nano-Interleaved CFRP under Static and Fatigue Loading

Fibers ◽  
2019 ◽  
Vol 7 (2) ◽  
pp. 13 ◽  
Author(s):  
Mohamad Fotouhi ◽  
Cristiano Fragassa ◽  
Sakineh Fotouhi ◽  
Hamed Saghafi ◽  
Giangiacomo Minak
Keyword(s):  
Acoustic Emissions ◽  
Weight Ratio ◽  
Laminated Composite ◽  
High Strength ◽  
Fatigue Loading ◽  
Fatigue Tests ◽  
Limiting Factor ◽  
Delamination Toughness ◽  
Delamination Resistance ◽  
Laminated Composite Materials

The use of high strength-to-weight ratio-laminated fiber-reinforced composites is emerging in engineering sectors such as aerospace, marine and automotive to improve productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Previous studies have proven that ply interface nanofibrous fiber reinforcement has an effective influence on delamination resistance of laminated composite materials. This paper aims to investigate the effect of nanofiber ply interface reinforcement on mode I properties and failure responses when being subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) experiments. Static and fatigue tests were performed in accordance with standards and the Acoustic Emissions (AE) were acquired during these tests. The results showed not only a 130% increase of delamination toughness for nanomodified specimens in the case of static loads, but also a relevant crack growth resistance in the case of fatigue loads. In addition, the AE permitted to relate these improvements to the different failure mechanisms occurring.

scholarly journals Effect of UV Ageing on the fatigue life of bulk polyethylene

2018 ◽  
Vol 165 ◽  
pp. 08002 ◽  
Author(s):  
Hamza Lamnii ◽  
Moussa Nait-Abdelaziz ◽  
Georges Ayoub ◽  
Jean-Michel Gloaguen ◽  
Ulrich Maschke ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Uv Irradiation ◽  
Chemical Structure ◽  
Fatigue Behavior ◽  
Crystalline Polymer ◽  
Fatigue Loading ◽  
Chain Scission ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Irradiation Effect

Polymers operating in various weathering conditions must be assessed for lifetime performance. Particularly, ultraviolet (UV) radiations alters the chemical structure and therefore affect the mechanical and fatigue properties. The UV irradiation alters the polymer chemical structure, which results into a degradation of the mechanical and fatigue behavior of the polymer. The polymer properties degradation due to UV irradiation is the result of a competitive process of chain scission versus post-crosslinking. Although few studied investigated the effect of UV irradiation on the mechanical behaviour of thermoplastics, fewer examined the UV irradiation effect on the fatigue life of polymers. This study focuses on investigating the effect of UV irradiation on the fatigue properties of bulk semi-crystalline polymer; the low density Polyethylene (LDPE). Tensile specimens were exposed to different dose values of UV irradiation then subjected to fatigue loading. The fatigue tests were achieved under constant stress amplitude at a frequency of 1Hz. The results show an important decrease of the fatigue limit with increasing absorbed UV irradiation dose.

Sign in / Sign up

Export Citation Format

Share Document