scholarly journals Effect of Heat Treatment on Microstructure and Mechanical Properties of the AZ31/WE43 Bimetal Composites

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 971
Author(s):  
Dexing Xu ◽  
Kangning Zhao ◽  
Changlin Yang ◽  
Hongxiang Li ◽  
Jishan Zhang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Shear Strength ◽  
Rare Earth ◽  
Solution Treatment ◽  
Interfacial Strength ◽  
High Melting ◽  
High Melting Point ◽  
Microstructure And Mechanical Properties ◽  
Strength And Plasticity

Effect of heat treatment on the microstructure and mechanical properties of the AZ31/WE43 bimetal composites was investigated, and the optimized solution treatment and ageing treatment parameters were achieved. After heat treatment, it was found that that the high melting-point Y-rich phases and Mg-RE (rare earth) phases at the interface were distributed more uniformly, so the interfacial strength and plasticity were improved. Meanwhile, the shear strength and plasticity of AZ31 were increased, and the shear strength of WE43 was also improved by heat treatment. The evolution of interface morphologies and enhancement of the mechanical properties at the interface will be discussed in detail.

Effects of Gd on Microstructure and Mechanical Properties of AZ61 Magnesium Alloy

2011 ◽  
Vol 284-286 ◽  
pp. 500-504 ◽  
Author(s):  
Dai Dong Zhang ◽  
Hu Zhang ◽  
Xue Hua Yu ◽  
Xiao Ru Zhang ◽  
Da Qing Fang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Rare Earth ◽  
High Temperature ◽  
Room Temperature ◽  
High Melting ◽  
High Melting Point ◽  
Az61 Magnesium Alloy ◽  
Microstructure And Mechanical Properties ◽  
Dislocation Movement

The effects of different amounts of rare earth Gd added into AZ61 on the microstructure and mechanical properties of magnesium alloys were studied in this paper. And it adopts T6 heat treatment. When 2% Gd has been added, the microstructure of the alloy becomes uniform. The grains are refining. Gd is prior to reacting with Al for forming Al2Gd phase with high melting point. It is in the form of dot-like and globosity along the grain boundary. And β-Mg17A112 phase is reduced and its shape is thinner. The Al2Gd phase hinders dislocation movement. It markedly improves the mechanical properties of the alloy at room temperature and high temperature.

Microstructure and Mechanical Properties of Mg-Y Alloys

2011 ◽  
Vol 239-242 ◽  
pp. 352-355
Author(s):  
Quan An Li ◽  
Qing Zhang ◽  
Chang Qing Li ◽  
Yao Gui Wang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Rare Earth ◽  
Melting Point ◽  
Room Temperature ◽  
Optimum Combination ◽  
High Melting ◽  
High Melting Point ◽  
Microstructure And Mechanical Properties ◽  
The Matrix

The effects of 2-12 wt.% Y addition on the microstructure and mechanical properties of as-cast Mg-Y binary alloys have been investigated. The results show that proper content of rare earth Y addition can obviously refine the grains and form high melting point Mg24Y5 phases in the matrix, and improve the microstructure and mechanical properties of the alloys. At room temperature, the optimum combination of ultimate tensile strength and elongation, 195MPa and 7.5%, is obtained in Mg-10 wt.% Y alloy.

Effect of Heat Treatment on Microstructure and Mechanical Properties in ZK60 Alloy Sheet

2007 ◽  
Vol 567-568 ◽  
pp. 361-364 ◽  
Author(s):  
Suk Bong Kang ◽  
Jae Hyung Cho ◽  
Hyoung Wook Kim ◽  
Y.M Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Growth Direction ◽  
Warm Rolling ◽  
Alloy Sheet ◽  
Microstructure And Mechanical Properties ◽  
Zk60 Alloy ◽  
Hardness Values

The sheet of ZK60 alloy with a thickness of 1mm was prepared from a casting ingot followed by homogenization and warm-rolling. Variations in microstructure and mechanical properties of ZK60 alloy sheets were investigated during T6 treatment. Especially artificial aging after solution heat treatment affected both precipitates distribution and mechanical properties with aging treatment. Variations of mechanical properties were related to precipitates, i.e. rod-shaped ( 1 β ′ ) or disc shaped ( 2 β ′ ) particles. Around the peak of hardness values, regularly distributed rod-shaped ( 1 β ′ ) precipitates were found. The rod-shaped ( 1 β ′ ) precipitates were oriented with a growth direction of [0001]. When over-aged, rod-shaped ( 1 β ′ ) precipitates were expected to decrease and the density of disc-shaped ( 2 β ′ ) precipitates to change. The rod-shaped ( 1 β ′ ) precipitates mainly consist of {Mg, Zn}, while disc-shaped ( 2 β ′ ) precipitates, {Mg, Zn, Zr} or {Mg, Zn}. In this study the optimum T6 treatment was determined as solution treatment at 430 °C for 6 hours and subsequently aging treatment at 175 °C for 18 hours. At this T6 condition the tensile strength, yield strength and elongation are 321MPa, 280MPa and 16%, respectively.

Effect of Heat Treatment on Microstructure and Mechanical Properties of MA2-1 Alloy Sheet

2005 ◽  
Vol 488-489 ◽  
pp. 151-154
Author(s):  
Weichao Zheng ◽  
Xiao Li Sun ◽  
Peijie Li ◽  
Daben Zeng ◽  
L.B. Ber
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
High Purity ◽  
Solution Treatment ◽  
Optical Microscope ◽  
Alloy Sheet ◽  
Β Phase ◽  
Microstructure And Mechanical Properties ◽  
Mg17al12 Phase

Effect of heat treatment on the microstructure and mechanical properties of high purity MA2-1(Mg-5wt.%Al-1wt.%Zn-0.4wt.%Mn) alloy sheet were investigated. X-ray diffraction analysis indicated that the microstructure of high purity MA2-1 alloy sheet annealed consisted of α-Mg solid solution, β (Mg17Al12) phase and Al-Mn phases such as Al6Mn and Al10Mn3. β phase dissolved into α-Mg solid solution during the solution treatment and formed supersaturated α-Mg solid solution. After aging at the temperatures of 423 K, 473 K and 523 K for 12 hours, β phase precipitated from the supersaturated α-Mg solid solution. Optical microscope observation found that the grain size of the MA2-1 alloy sheet became larger after heat treatment. As a result, the mechanical properties of the MA2-1 alloy sheet such as the tensile strength and yield strength declined after the heat treatment.

Effects of Ca on Microstructure and Mechanical Properties of Mg-5.5Al-1.2Y Alloy

2012 ◽  
Vol 198-199 ◽  
pp. 216-219
Author(s):  
Wen Jian Liu ◽  
Quan An Li ◽  
Zhi Chen ◽  
Xiao Jie Song
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperature ◽  
Melting Point ◽  
Magnesium Alloy ◽  
Intermetallic Compounds ◽  
High Melting ◽  
High Melting Point ◽  
Dramatic Decrease ◽  
Microstructure And Mechanical Properties ◽  
Ca Addition

The microstructure and mechanical properties of aged Mg-5.5Al-1.2Y magnesium alloy with Ca addition are investigated. The results show that with 1.0wt.% Ca addition, the phase of Al2Y is refined obviously and the phase of Mg17Al12 has a dramatic decrease in number. And, high melting point intermetallic compounds Al2Ca and Al4Ca are formed. Meanwhile, the β-Mg17Al12 phase become more dispersed. After 1.0wt.% Ca addition, the mechanical properties of the alloy at room and elevated temperature are improved.

Effect of Solution Treatment and Extrusion on the Microstructure and Mechanical Properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr Alloy

2011 ◽  
Vol 197-198 ◽  
pp. 1125-1128 ◽  
Author(s):  
Jing Jiang Nie ◽  
Liang Meng ◽  
Xiu Rong Zhu ◽  
Yong Dong Xu ◽  
Yue Yi Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Time ◽  
Solution Treatment ◽  
Solution Treated ◽  
Microstructure And Mechanical Properties ◽  
Combined Action ◽  
Strength And Ductility

The effect of the combined action of hot work and heat treatment on the microstructure and mechanical properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr (wt. %) (E21) alloy was investigated. Results showed that the solution treatment time of the ingot played a great effect on the mechanical properties of the extruded alloy. With solution treating time of the ingot increasing, the tensile strength of the extruded alloy decreased gradually, but the elongation increased greatly. The best combination of strength and ductility was achieved for the extruded alloy after the ingot solution treated at 520°C for 3 h, extrusion at 400°C and aging at 200°C for 16 h, namely ultimate tensile strength = 331MPa and elongation = 7.1%.

scholarly journals Effects of Silicon and Heat-Treatment on Microstructure and Mechanical Properties of Biomedical Ti-39Nb-6Zr Alloy

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 268
Author(s):  
Ji-Hoon Jang ◽  
Dong-Geun Lee
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
Elastic Modulus ◽  
Solution Treatment ◽  
Aging Treatment ◽  
Treatment Temperature ◽  
Shielding Effect ◽  
Microstructure And Mechanical Properties ◽  
Tissue Reactions

The cytotoxic tissue reactions of alloying elements (Al, V) of Ti-6Al-4V have been reported, whereas the Ti-39Nb-6Zr (TNZ40) alloy developed by adding β-phase stabilizing elements is known to have no cytotoxicity and exhibits excellent biocompatibility. In addition, there is a slight modulus difference between the TNZ40 alloy and human bones as the elastic modulus of the TNZ40 alloy is very low. This can inhibit detrimental effects such as osteoblast loss due to a stress-shielding effect. In this study, various Si contents were added and heat treatment under various conditions was performed to control the microstructure and mechanical properties of the TNZ40 alloy. In the β-type titanium alloy, the ω phase is commonly observed by quenching from the solution-treatment or aging-treatment temperature. These ω precipitates can typically increase the elastic modulus, hardness, and embrittlement of the β-type titanium alloy, which are important to control this phase. The correlation between Si content and precipitation and the effects of solution treatment and aging condition on the mechanical properties such as tensile strength, and hardness, were analyzed.

Microstructures and Mechanical Properties of AJ62 Magnesium Alloy with Y and Nd Elements

2011 ◽  
Vol 686 ◽  
pp. 253-259
Author(s):  
Xu Ning ◽  
Wei Dong Xie ◽  
Chun Mei Dang ◽  
Xiao Dong Peng ◽  
Yan Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Tensile Strength ◽  
Rare Earth ◽  
Magnesium Alloy ◽  
Room Temperature ◽  
Solution Treatment ◽  
Solid Solution Treatment ◽  
Microstructure And Mechanical Properties ◽  
Microstructures And Mechanical Properties

A series of Mg-6Al-2Sr-1.5Y-xNd (x=0, 0.3, 0.6, 0.9, 1.2) alloy samples were prepared and their microstructures were observed and mechanical properties were measured. The existing forms of Y and Nd were studied. The effects of Y and Nd on microstructure and mechanical properties of AJ62 alloy were investigated. The results show that the main existing forms of Y and Nd in AJ62 alloy are Al2Y and Al2Nd. The combined addition of rare earth Y and Nd can refine α-Mg matrix obviously and reduce the amount of the β-Mg17Al12phases; after solid solution treatment, the tensile strength of the alloys rise first and fall later with increasing content of Nd. When the content of Nd is about 0.6%wt, the values of tensile strengthes are up to the maximum both at room temperature and at 448 K.

scholarly journals Effect of Austenization Temperature on the Microstructure in Cr-Mn-Si Steel

2019 ◽  
Vol 9 (2) ◽  
pp. 4942-4945
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Trace Elements ◽  
Polymorphic Transformation ◽  
High Strength ◽  
Heat Treatments ◽  
Thermal Treatments ◽  
Microstructure And Mechanical Properties ◽  
Bainite Structure ◽  
Strength And Plasticity

This work is a part of research on the microstructure and mechanical properties of Cr-Mn-Si steels after various thermal treatments. In order to increase the resistance of the materials against failure it is necessary to possess simultaneously high strength and plasticity at the same time. Normally, in conventional metals, this is impossible. The purpose of the present study is to trace the polymorphic transformation of the microstructure and the redistribution of the trace elements in the corresponding microstructural transformations of the steel at each stage of applied heat treatment - austenization, quenching, austempering, tempering. The chosen sequence of applied heat treatments is to obtain a bainite structure of up to 50% in order to achieve high strength and toughness of the material.

scholarly journals Effect of Deformation on Microstructure and Mechanical Properties of Medium Carbon Steel During Heat Treatment Process

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Yan Peng ◽  
Caiyi Liu ◽  
Ningning Wang
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Carbon Steel ◽  
Heating Temperature ◽  
Lath Martensite ◽  
Medium Carbon Steel ◽  
Medium Carbon ◽  
Experimental Steel ◽  
Microstructure And Mechanical Properties ◽  
Strength And Plasticity

AbstractThe current research of the Q-P and Q-P-T process has been focused on controlling the heating temperature and holding time, or adding alloy elements into the steel to induce precipitation strengthening and improve the strength and plasticity of the steel. In this article, based on a quenching-partitioning-tempering (Q-P-T) process combined with a hot deformation technology, a deforming-quenching-partitioning-tempering (D-Q-P-T) process was applied to medium carbon steel. The effect of the heat treatment parameters on the microstructure and mechanical properties of experimental steel under deformation was studied. Through use of a scanning electron microscope (SEM), transmission electron microscopy (TEM) and tensile tests, the optimal heat treatment conditions for realizing high strength and plasticity that meet the safety requirements were obtained. The mechanism for the D-Q-P-T process to improve the strength and plasticity of experimental steel was discussed. A multiphase composite structure of lath martensite and retained austenite was obtained. Compared with the Q-P-T process, use of the D-Q-P-T process can increase the strength of steel by 57.77 MPa and the elongation by 5%. This study proposes a method to improve the strength and plasticity of steel.

Sign in / Sign up

Export Citation Format

Share Document