scholarly journals Comparison of Engine Performance between Nano- and Microemulsions of Solketal Droplets Dispersed in Diesel Assisted by Microwave Irradiation

Molecules ◽  
2019 ◽  
Vol 24 (19) ◽  
pp. 3497 ◽  
Author(s):  
Cherng-Yuan Lin ◽  
Shih-Ming Tsai
Keyword(s):  
Diesel Engine ◽  
Microwave Irradiation ◽  
Engine Performance ◽  
Tween 80 ◽  
Continuous Phase ◽  
Gas Temperature ◽  
Surfactant Mixtures ◽  
Ultra Low Sulfur Diesel ◽  
Droplet Sizes ◽  
Exhaust Gas Temperature

As a derivative product of bio-glycerol, this study first uses solketal as a combustion improver for enhancing diesel engine characteristics. The emulsions of nanometer- and micrometer-sized droplets of solketal, which disperse evenly in the ultra-low sulfur diesel (ULSD), are formed by the effects of microwave irradiation. The performance of diesel engine fueled with the nanoemulsion of ULSD with scattered solketal droplets is analyzed and compared to that with the microemulsion. The experimental results show that the nanoemulsions can form when over 15 wt. % surfactant mixtures of Span 80 and Tween 80 and less than 5 wt. % solketal are mixed and emulsified with the remaining ULSD content, which acts as the continuous phase of the emulsions. The nanoemulsions are observed to have significantly lower brake-specific fuel consumption (bsfc) and higher fuel conversion efficiency and exhaust gas temperature than those of the microemulsions and the neat ULSD. However, the bsfc of the nanoemulsions increases with greater engine speed and gradually approaches those of the latter two test fuels. In addition, the dispersed solketal droplet sizes are mostly concentrated around 127 nm with peak intensity of 12.65% in the nanoemulsions. The microwave-assisted formation used in this study is found to successfully produce the nanoemulsions in which all of the dispersed droplet sizes are much smaller than 1000 nm.

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

Design and Development of Surge Tank for NOx Emission Reduction in B20 Biofueled Diesel Engine

2020 ◽  
Vol 12 (5) ◽  
Author(s):  
Jaspreet Hira ◽  
Basant Singh Sikarwar ◽  
Rohit Sharma ◽  
Vikas Kumar ◽  
Prakhar Sharma
Keyword(s):  
Diesel Engine ◽  
Research Work ◽  
Engine Performance ◽  
Nox Emission ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Surge Tank ◽  
Brake Thermal Efficiency ◽  
Exhaust Gas Temperature

In this research work, a surge tank is developed and utilised in the diesel engine for controlling the NOX emission. This surge tank acts as a damper for fluctuations caused by exhaust gases and also an intercooler in reducing the exhaust gas temperature into the diesel engine intake manifold. With the utilisation of the surge tank, the NOX emission level has been reduced to approximately 50%. The developed surge tank is proved to be effective in maintaining the circulation of water at appropriate temperatures. A trade-off has been established between the engine performance parameters including the brake thermal efficiency, brake specific fuel consumption, exhaust gas temperature and all emission parameters including HC and CO.

scholarly journals An Effect of Biosolar-Water Emulsion on Small Marine Diesel Engine

2018 ◽  
Vol 6 (6) ◽  
Author(s):  
Beny Cahyono ◽  
Taufik Fajar Nugroho ◽  
Tony Bambang Musriyadi
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Test Results ◽  
Gas Temperature ◽  
Water Emulsion ◽  
Light Duty ◽  
Marine Diesel ◽  
Tier 3 ◽  
Exhaust Gas Temperature ◽  
Small Capacity

This study aims to analyze the effect of water/biosolar emulsion fuel on the performance of engine diesel used in small capacity diesel engines. The fuel used is a mixture of biosolar 20% which is added 10% and 15% water (b20,WDE 10%, WDE 15%) which will be compared with dexlite fuel and biodiesel 20% (b20). Measurement of engine performance with various fuels was carried out in accordance with IMO marine engine regulation tier 3. The water-emulsified diesel could be used in the light-duty small diesel engine without modifications. The result shows that the net diesel fuel consumption and the exhaust gas temperature decreased with increasing water content of fuels over the investigated loading range.Performance produced by DWE 10% and 15% will been reduce Power, and Torque at each RPM. In detail, DWE 10% has better results than the DWE 15%. In the NOx emission test results, the use of water/biodiesel emulsified fuels 10% and 15% can reduce NOx emissions.

Performance of Diesel Engine Operating with Waste Plastic Disposal Fuel

2013 ◽  
Vol 465-466 ◽  
pp. 423-427 ◽  
Author(s):  
Mohd Herzwan Hamzah ◽  
Abdul Adam Abdullah ◽  
Agung Sudrajat ◽  
Nur Atiqah Ramlan ◽  
Nur Fauziah Jaharudin
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Waste Product ◽  
Engine Performance ◽  
Alternative Fuel ◽  
Constant Load ◽  
Gas Temperature ◽  
Waste Plastic ◽  
Exhaust Gas Temperature ◽  
Engine Power

Nowadays, many researches are conducted to produce alternative fuel. In order to overcome increasing price of fossil fuel and environmental issues, fuel from natural sources such as palm, rapeseed and jathropa are increasingly being utilized to produce bio-fuel. Similar as natural source, waste product such as plastics and tires also can be processed to produce alternative fuel. In this paper, engine performance of diesel engine operating with 100% waste plastic disposal fuel (WPDF) is analyzed and compared to diesel fuel. The experiment is conducted using single cylinder YANMAR TF120M diesel engine which is operating at variable speed and constant load. The performance parameters that analyzed in the experiment are engine power, torque, combustion pressure and exhaust gas temperature. Results of the experiment shows that waste plastic disposal fuel (WPDF) potentially can be use as alternative fuel in diesel engine. However, based on the data obtained, performance of diesel engine operating with WPDF is lower compared to diesel fuel.

scholarly journals The Influence of Emulsified Water Fuel Containing Fresh Water Microalgae on Diesel Engine Performance, Combustion, Vibration and Emission

Energies ◽  
2019 ◽  
Vol 12 (13) ◽  
pp. 2546
Author(s):  
Saddam H. Al-lwayzy ◽  
Talal Yusaf ◽  
Khalid Saleh ◽  
Belal Yousif
Keyword(s):  
Diesel Engine ◽  
Fresh Water ◽  
Energy Content ◽  
Engine Performance ◽  
Gas Temperature ◽  
Higher Power ◽  
Performance And Emissions ◽  
Emulsified Water ◽  
Exhaust Gas Temperature ◽  
Vibration Performance

Microalgae is considered as an excellent potential renewable source of fuel in many forms including powder or slurry. A high percentage of emulsified water in the fuel is reported to reduce diesel engines’ emissions such as NOx, but that will compromise the engine output power. Using microalgae powder as an additive to enhance the emulsified water fuel heating value is the main objective of this work. Diesel engine combustion, vibration, performance and emissions were evaluated for pure cottonseed biodiesel (CS-B100), emulsified water 20% (vol.) in cottonseed biodiesel (CSB-E20) and emulsified water 20% (vol.) containing Fresh Water Microalgae Chlorella Vulgaris (FWM-CV) in cottonseed biodiesel (CSB-ME20). The emulsified water fuels showed a reduction in in-cylinder pressure, vibration, brake power, torque, exhaust gas temperature, CO2 and NOx, while BSFC and O2 were higher than the pure biodiesel (CS-B100). CSB-ME20 produced higher power and torque than CSB-E20 due to the presence of microalgae in the fuel that increased the energy content of the fuel.

scholarly journals Effect of Producer Gas from Redgram Stalk and Combustion Chamber Types on the Emission and Performance Characteristics of Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5879
Author(s):  
K. M. Akkoli ◽  
N. R. Banapurmath ◽  
Suresh G ◽  
Manzoore Elahi M. Soudagar ◽  
T. M. Yunus Khan ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Engine Performance ◽  
Nozzle Geometry ◽  
Producer Gas ◽  
Gas Temperature ◽  
Combustion Chambers ◽  
And Performance ◽  
Exhaust Gas Temperature ◽  
Emission And Performance

The engine performance has been improved by modifying the combustion chamber shape of the diesel engine for dual-fuel operation with liquid fuel and producer gas (PG). The combined effect of gaseous fuel from redgram stalk and combustion chamber type on the emission and performance of blended-fuel of diesel and HOME biodiesel–PG has been investigated. In this experimental study, four varieties of combustion chambers hemispherical (HCC), low swirl (LSCC), dual swirl (DSCC), and toroidal re-entrant (TRCC) were analyzed comprehensively. The results presented that the TRCC configuration with a given nozzle geometry has 9% improved brake thermal efficiency (BTE) and 10.4% lower exhaust gas temperature (EGT). The smoke, unburnt hydrocarbon (UBHC), and carbon monoxide (CO) decreased by 10–40%, but a 9% increase in nitrogen oxides (NOX) emission levels was observed with TRCC. The delay period and combustion period were decreased by 5% and 7%. The fuel replacement of about 71% for the diesel–PG combination with HCC and 68% for the HOME–PG combination with TRCC was achieved.

Engine Performance Investigations of Palm Oil, Jatropha Oil and Waste Cooking Oil as Alternative Fuel

2015 ◽  
Vol 1113 ◽  
pp. 674-678
Author(s):  
Syarifah Yunus ◽  
Noriah Yusoff ◽  
Muhammad Faiz Fikri Ahmad Khaidzir ◽  
Siti Khadijah Alias ◽  
Freddawati Rashiddy Wong ◽  
...  
Keyword(s):  
Palm Oil ◽  
Engine Performance ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Gas Temperature ◽  
Performance Effect ◽  
Cooking Oil ◽  
Exhaust Gas Temperature ◽  
Global Agenda

The continued using of petroleum energy as a sourced for fuel is widely recognized as unsustainable because of the decreasing of supplies while increasing of the demand. Therefore, it becomes a global agenda to develop a renewable, sustainable and alternative fuel to meets with all the demand. Thus, biodiesel seems to be one of the best choices. In Malaysia, the biodiesel used is from edible vegetable oil sources; palm oil. The uses of palm oil as biodiesel production source have been concern because of the competition with food materials. In this study, various types of biodiesel feedstock are being studied and compared with diesel. The purpose of this comparison is to obtain the optimum engine performance of these different types of biodiesel (edible, non-edible, waste cooking oil) on which are more suitable to be used as alternative fuel. The optimum engine performance effect can be obtains by considering the Brake Power (BP), Specific Fuel Consumption (SFC), Exhaust Gas Temperature (EGT) and Brake Thermal Efficiency (BTE).

Effect of Fuel Injection Strategy on DPF Regeneration in Single Cylinder Diesel Engine

2015 ◽  
Author(s):  
Sungjun Yoon ◽  
Hongsuk Kim ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Experimental Results ◽  
Exhaust Gas ◽  
Post Injection ◽  
Gas Temperature ◽  
Injection Strategy ◽  
Dpf Regeneration ◽  
Exhaust Gas Temperature

Stringent emission regulations (e.g., Euro-6) force automotive manufacturers to equip DPF (diesel particulate filter) on diesel cars. Generally, post injection is used as a method to regenerate DPF. However, it is known that post injection deteriorates specific fuel consumption and causes oil dilution for some operating conditions. Thus, an injection strategy for regeneration becomes one of key technologies for diesel powertrain equipped with a DPF. This paper presents correlations between fuel injection strategy and exhaust gas temperature for DPF regeneration. Experimental apparatus consists of a single cylinder diesel engine, a DC dynamometer, an emission test bench, and an engine control system. In the present study, post injection timing covers from 40 deg aTDC to 110 deg aTDC and double post injection was considered. In addition, effects of injection pressures were investigated. The engine load was varied from low-load to mid-load and fuel amount of post injection was increased up to 10mg/stk. Oil dilution during fuel injection and combustion processes were estimated by diesel loss measured by comparing two global equivalences ratios; one is measured from Lambda sensor installed at exhaust port, the other one is estimated from intake air mass and injected fuel mass. In the present study, the differences in global equivalence ratios were mainly caused from oil dilution during post injection. The experimental results of the present study suggest an optimal engine operating conditions including fuel injection strategy to get appropriate exhaust gas temperature for DPF regeneration. Experimental results of exhaust gas temperature distributions for various engine operating conditions were summarized. In addition, it was revealed that amounts of oil dilution were reduced by splitting post injection (i.e., double post injection). Effects of injection pressure on exhaust gas temperature were dependent on combustion phasing and injection strategies.

scholarly journals Performance Analysis of Direct Injection Diesel Engine Fueled with Diesel-Tomato Seed Oil Biodiesel Blending by ANOVA and ANN

Energies ◽  
2019 ◽  
Vol 12 (23) ◽  
pp. 4421 ◽  
Author(s):  
Karami ◽  
Rasul ◽  
Khan ◽  
Anwar
Keyword(s):  
Diesel Engine ◽  
Performance Analysis ◽  
Direct Injection ◽  
Engine Performance ◽  
Gas Temperature ◽  
Ann Model ◽  
Tomato Seed ◽  
Significance Level ◽  
Di Diesel Engine ◽  
Biodiesel Fuels

Biodiesel is an alternative fuel for diesel engine. Considering the differences between diesel and biodiesel fuels, the engine condition should be modified based on the fuel or fuel blends to achieve optimum performance. This study presented a performance analysis of a direct-injected (DI) diesel engine with a dynamometer fueled with diesel-tomato seed biodiesel (TSOB) blends employing ANOVA and universal nonlinear model based on ANN. The experiments were carried out under conditions of some independent variables including different engine loads (0, 50, 100%) and speed (1800, 2150, and 2500 rpm) for four diesel-biodiesel combinations (B0, B5, B10, and B20). In this research, the effect of these factors on dependent variables including power, torque, SFC, FC, and Exhaust Gas Temperature (EGT) are investigated. Duncan′s multi-domain test at a significance level of R < 0.01 shows that the highest and lowest of the torque and power are produced from B5 and B20, respectively. These results show that the lowest EGT of 613 K is related to B20 and the highest EGT is related to B5 and B10. The regression models showed that the torque decreases with increasing the engine speed and biodiesel percentage. These results also show that the highest and the lowest SFC is related to B0 and B20, respectively. The ANN model shows high capability of predicting the engine performance parameters and emissions, without running costly and time-consuming experiments with the histogram error of 0.004 and R = 0.96. It also proved that ANN is a non-linear model of choice to deal with these data, instead of multivariate linear regression employed for preliminary analysis.

scholarly journals A model-based and experimental approach for the determination of suitable variable valve timings for cold start in partial load operation of a passenger car single-cylinder diesel engine

2018 ◽  
Vol 20 (1) ◽  
pp. 141-154 ◽  
Author(s):  
P Maniatis ◽  
U Wagner ◽  
T Koch
Keyword(s):  
Diesel Engine ◽  
Experimental Investigations ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Warm Up ◽  
One Dimensional ◽  
Engine Efficiency ◽  
Residual Gas ◽  
Dimensional Simulation ◽  
Exhaust Gas Temperature

A manipulation of the charge exchange allows controlling the amount of residual gas during engine warm-up. The residual gas during the warm-up phase leads to an increase of the exhaust gas temperature and supports to reach the exhaust after-treatment system operating temperature faster. In addition, the warm residual gas increases the combustion chamber temperature, which reduces the HC and CO emissions. However, fuel consumption increases. For that reason, such heating measures should be the best compromise of both, exhaust gas temperature increase and engine efficiency, in order to provide efficient heating strategies for passenger car diesel engines. Therefore, simulative and experimental investigations are carried out at the Institute of Internal Combustion Engines of the Karlsruhe Institute of Technology to establish a reliable cam design methodology. For the experimental investigations, a modern research single-cylinder diesel engine was set up on a test bench. In addition, a one-dimensional simulation model of the experimental setup was created in order to simulate characteristics of valve lift curves and to investigate their effects on the exhaust gas temperature and the exhaust gas enthalpy flow. These simulations were based on design of experiments (DoE), so that all characteristics can be used sustainably for modeling and explaining their influences on the engine operation. This methodology allows numerically investigating promising configurations and deriving cam contours which are manufactured for testing. To assess the potential of these individual configurations, the results obtained were compared with each other as well as with the series configuration. Results show that the combination of DoE and one-dimensional simulation for the design of camshaft contours is well suited which was also validated with experimental results. Furthermore, the potential of residual gas retention by favorable configurations with a second event already revealed in various publications could be confirmed with respect to exhaust gas temperature increase and engine efficiency.

Sign in / Sign up

Export Citation Format

Share Document