scholarly journals Chitosan Films Obtained from Brachystola magna (Girard) and Its Evaluation on Quality Attributes in Sausages during Storage

Molecules ◽  
2021 ◽  
Vol 26 (6) ◽  
pp. 1782
Author(s):  
Juan Manuel Tirado-Gallegos ◽  
Paul Baruk Zamudio-Flores ◽  
Miguel Espino-Díaz ◽  
René Salgado-Delgado ◽  
Gilber Vela-Gutiérrez ◽  
...  
Keyword(s):  
Weight Loss ◽  
Lipid Oxidation ◽  
Meat Products ◽  
Water Vapor Permeability ◽  
Good Alternative ◽  
Quality Attributes ◽  
Vapor Permeability ◽  
Biodegradable Films ◽  
Molecular Weights ◽  
Chitosan Films

High molecular weight chitosan (≈322 kDa) was obtained from chitin isolated from Brachystola magna (Girard) to produced biodegradable films. Their physicochemical, mechanical and water vapor permeability (WVP) properties were compared against commercial chitosan films with different molecular weights. Brachystola magna chitosan films (CFBM) exhibited similar physicochemical and mechanical characteristics to those of commercial chitosans. The CFBM films presented lower WVP values (10.01 × 10−11 g/m s Pa) than commercial chitosans films (from 16.06 × 10−11 to 64.30 × 10−11 g/m s Pa). Frankfurt-type sausages were covered with chitosan films and stored in refrigerated conditions (4 °C). Their quality attributes (color, weight loss, pH, moisture, texture and lipid oxidation) were evaluated at 0, 5, 10, 15 and 20 days. Sausages covered with CFMB films presented the lowest weight loss (from 1.24 to 2.38%). A higher increase in hardness (from 22.32 to 30.63 N) was observed in sausages covered with CFMB films. Compared with other films and the control (uncovered sausages), CFMB films delay pH reduction. Moreover, this film presents the lower lipid oxidation level (0.10 malonaldehyde mg/sample kg). Thus, chitosan of B. magna could be a good alternative as packaging material for meat products with high-fat content.

scholarly journals Protein-Based Films and Coatings for Food Industry Applications

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 769
Author(s):  
Vlad Mihalca ◽  
Andreea Diana Kerezsi ◽  
Achim Weber ◽  
Carmen Gruber-Traub ◽  
Jürgen Schmucker ◽  
...  
Keyword(s):  
Food Packaging ◽  
Meat Products ◽  
Water Vapor Permeability ◽  
Food Product ◽  
Edible Films ◽  
Vapor Permeability ◽  
Area Of Interest ◽  
Industry Applications ◽  
Economic Perspectives ◽  
Materials Used

Food packaging is an area of interest not just for food producers or food marketing, but also for consumers who are more and more aware about the fact that food packaging has a great impact on food product quality and on the environment. The most used materials for the packaging of food are plastic, glass, metal, and paper. Still, over time edible films have become widely used for a variety of different products and different food categories such as meat products, vegetables, or dairy products. For example, proteins are excellent materials used for obtaining edible or non-edible coatings and films. The scope of this review is to overview the literature on protein utilization in food packages and edible packages, their functionalization, antioxidant, antimicrobial and antifungal activities, and economic perspectives. Different vegetable (corn, soy, mung bean, pea, grass pea, wild and Pasankalla quinoa, bitter vetch) and animal (whey, casein, keratin, collagen, gelatin, surimi, egg white) protein sources are discussed. Mechanical properties, thickness, moisture content, water vapor permeability, sensorial properties, and suitability for the environment also have a significant impact on protein-based packages utilization.

scholarly journals Preparation, properties and applications of wheat gluten edible films

2000 ◽  
Vol 9 (1) ◽  
pp. 23-35 ◽  
Author(s):  
P. TANADA-PALMU ◽  
H. HELÉN ◽  
L. HYVÖNEN
Keyword(s):  
Weight Loss ◽  
Tensile Strength ◽  
Water Vapor ◽  
Wheat Gluten ◽  
Single Layer ◽  
Water Vapor Permeability ◽  
Edible Films ◽  
Bilayer Film ◽  
Vapor Permeability ◽  
Elongation At Break

Edible films from wheat gluten were prepared with various amounts of glycerol as a plasticizer. Water vapor permeability, oxygen permeability, tensile strength and percentage elongation at break at different water activities ( aw ) were measured. Films with low amounts of glycerol had lower water vapor and oxygen permeabilities, higher tensile strength and lower elongation at break. Wheat gluten coatings reduced weight loss during two weeks of storage for cherry tomatoes and sharon fruits compared to uncoated controls. A bilayer film of wheat gluten and beeswax significantly lowered weight loss from coated cheese cubes compared to single layer coating of wheat gluten.;

Development of Biodegradable Films Based on Durian Seed Starch

2012 ◽  
Vol 506 ◽  
pp. 311-314 ◽  
Author(s):  
W. Pimpa ◽  
C. Pimpa ◽  
P. Junsangsree
Keyword(s):  
Mechanical Properties ◽  
Water Vapor ◽  
Food Processing ◽  
Corn Starch ◽  
Water Vapor Permeability ◽  
Cassava Starch ◽  
Raw Material ◽  
Vapor Permeability ◽  
Biodegradable Films ◽  
Durian Seed

Fresh durian seed consists largely of starch and can be considered such a suitable raw material for producing biodegradable films. The aim of this work was to develop biodegradable films based on durian seed starch (DSS) and to characterize their water barrier, microscopic and mechanical properties. DSS films were prepared by casting with glycerol as plasticizer. Corn starch and cassava starch, commonly used in food processing, were chosen to prepare films and compare their properties to the DSS-based films. Using a second biopolymer, carboxymethyl cellulose (CMC), in the DSS based composite has been studied as a strategy to improve their important properties. Water vapor permeability and elongation values were improved significantly (p<0.05) when 5% (w/w DSS) CMC was incorporated. Therefore, preparing biodegradable films from DSS is a new alternative for using this raw material which is sometimes much cheaper than commercial starches

Study of Diffusion and Water Vapor Permeability in Chitosan Films and Chitosan Emulsified Films

2012 ◽  
Vol 326-328 ◽  
pp. 170-175 ◽  
Author(s):  
Arlete Barbosa dos Reis ◽  
Cristiana Maria Pedroso Yoshida ◽  
Vera Solange Oliveira Farias ◽  
Wilton Pereira Silva
Keyword(s):  
Water Vapor ◽  
Lipid Analysis ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Oxygen Barrier ◽  
Water Vapor Barrier ◽  
Industry Waste ◽  
Diffusive Permeability ◽  
Hydrophobic Compound ◽  
Chitosan Films

Chitosan is an abundant, natural polysaccaride obtained from fishing industry waste and films of chitosan also provide an efficient oxygen barrier. However, they are a poor water vapor barrier, which can be improved by incorporation of a hydrophobic compound, forming a emulsified film. Chitosan films were produced with the addition of palmitic acid lipid analysis and then the process in parallel with the diffusive permeability to water vapor. The objective of this work was to characterize the diffusion and water vapor permeability behavior of chitosan films and chitosan emulsified films.

scholarly journals Measuring Transpiration Rates of Tomato and Other Detached Fruit

HortScience ◽  
1993 ◽  
Vol 28 (10) ◽  
pp. 1035-1038 ◽  
Author(s):  
Ahmad Shirazi ◽  
Arthur C. Cameron
Keyword(s):  
Weight Loss ◽  
Water Vapor ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Weight Changes ◽  
Experimental Conditions ◽  
Wide Range ◽  
Humidity Chamber ◽  
Water Transport Properties ◽  
Temperature Depression

A method was developed to measure transpiration rates and apparent water-vapor permeability coefficients (P'H2O) of detached fruit using an analytical balance equipped with a humidity chamber, wide-range humidity-generating and sensing devices, and a datalogger. The system was designed to monitor weight changes with time and, hence, weight loss of individual fruit during exposure to specific relative humidities (RHs) and temperatures. Weight loss was corrected for loss due to respiratory exchange of 02 and CO2 before calculating P'H2O. Values of P'H2O for tomatoes obtained using this method over periods of 5 minutes to 24 hours ranged from 3 to 12 nmol·cm-2·s-1·kPa-1 at 20C, depending on the experimental conditions. These values are similar to previously published values and to those obtained in a conventional weight-loss experiment, which involved intermittent weighing. P'H20 for tomatoes dropped ≈15% in 24 hours. P'H20 increased with a transient increase in RH; the extent of the increase was variable from fruit to fruit, ranging from 5% to 100% over 30% to 90% RH. The change was reversible in that P'H2O increased and decreased within minutes following shifts in RH. Similar changes were found for strawberry P'H20. The increase in P'H2O may be due, in part, to a direct effect of water vapor on the water transport properties of the cuticular polymer and surface temperature depression as a result of evaporative cooling. At 50% RH and 20C, water vapor diffuses from tomatoes 50 times faster than O2 enters on a molar basis. This information will be useful for modeling RH changes in modified-atmosphere packages.

scholarly journals Packaging properties and control of Listeria monocytogenes in bologna by cellulosic films incorporated with pediocin

2013 ◽  
Vol 16 (3) ◽  
pp. 226-235 ◽  
Author(s):  
Paula Judith Pérez Espitia ◽  
Jhon Jairo Reina Pacheco ◽  
Nathália Ramos de Melo ◽  
Nilda de Fátima Ferreira Soares ◽  
Alba Manuela Durango
Keyword(s):  
Antimicrobial Activity ◽  
Water Vapor ◽  
Listeria Monocytogenes ◽  
Biofilm Formation ◽  
Testing Machine ◽  
Meat Products ◽  
Gravimetric Method ◽  
Water Vapor Permeability ◽  
Vapor Permeability

Listeria monocytogenes is a foodborne pathogen, able to survive and proliferate at refrigeration temperatures. As a result, ready-to-eat meat products have been associated with major outbreaks. Producing meat products involves lethal preservation treatments, e.g. thermal treatments. Listeria contamination, however, may be introduced when products are sliced and packaged at retail businesses or delicatessens. In Brazil, sliced bologna is very popular at retail markets. After slicing, however, bologna has a short shelf-life. The aim of this work was to study the effects of pediocin incorporation on the load at break, water vapor permeability rate and structure, by microscopic analysis, of antimicrobial cellulosic packaging. The potential application of the developed packaging for the preservation of bologna and inhibition of Listeria biofilm formation was also studied. Cellulosic antimicrobial packaging films were produced with cellulose acetate and acetone. Pediocin (commercially available concentrate ALTA TM 2341) was incorporated at 30, 40 and 50 % w/w. The load at break of films was studied using the Universal Testing Machine (Instron) at 10 °C and 25 °C. The water vapor permeability was determined by gravimetric method. A scanning electron microscope was used to study the developed packaging structure. Antimicrobial activity of films against Listeria innoucua and L. monocytogenes was tested both in vitro and in bologna samples. Results showed that values of load at break decreased with increasing concentrations of pediocin at 10 °C and 25 °C. Regarding water vapor permeability, only the control and 50 % pediocin films presented statistical difference, with the 50 % pediocin film being more permeable. In vitro tests showed antimicrobial activity against L. innocua. Cellulosic film with 50 % pediocin reduced L. monocytogenes growth on sliced bologna by 1.2 log cycles after 9 days and prevented biofilm formation on packaging and bologna surfaces. Hence, active cellulosic films made with 50 % pediocin in the form of commercially available concentrated ALTA™ 2341 have the potential of being used in a system of hurdle technologies as a final obstacle for L. monocytogenes control in bologna preservation.

Photothermal configuration applied to the study of water vapor permeability in biodegradable films under several water activities

2003 ◽  
Vol 74 (1) ◽  
pp. 761-763 ◽  
Author(s):  
G. Lopez-Bueno ◽  
E. San Martı́n-Martı́nez ◽  
A. Cruz-Orea ◽  
S. A. Tomas ◽  
M. Tufiño ◽  
...  
Keyword(s):  
Water Vapor ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Biodegradable Films

scholarly journals Physicochemical and Antioxidant Properties of Chitosan Films Incorporated with Cinnamon Oil

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Marco A. López-Mata ◽  
Saul Ruiz-Cruz ◽  
Norma Patricia Silva-Beltrán ◽  
José de Jesús Ornelas-Paz ◽  
Víctor Manuel Ocaño-Higuera ◽  
...  
Keyword(s):  
Water Vapor ◽  
Antioxidant Properties ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Protective Effects ◽  
Protective Capacity ◽  
Cinnamon Oil ◽  
Low Concentrations ◽  
Yellow Coloration ◽  
Chitosan Films

Chitosan films (CF) with cinnamon bark oil (CO) incorporated at 0% (control), 0.25%, 0.5%, and 1.0% v/v were prepared by an emulsion method. The films were characterized based on their physical properties (solubility, water vapor permeability, optical property, and microstructure) and antioxidant properties (DPPH, ABTS, and its protective effects on human erythrocytes). The results showed that the incorporation of 0.5 and 1.0% of CO into the CF significantly decreased its solubility to 22% of the control (p<0.05). The water vapor permeability of the CF-CO was significantly reduced to 40% with low concentrations of CO (0.25%) incorporated into the CF. In general, the films presented a yellow coloration and an increase in transparency with the incorporation of CO into the CF. It was also observed that the incorporation of CO increased the antioxidant activity between 6.0-fold and 14.5-fold compared to the control, and the protective capacity against erythrocyte hemolysis increased by as much as 80%.

Sign in / Sign up

Export Citation Format

Share Document