scholarly journals Nanoscale Soft Wetting Observed in Co/Sapphire during Pulsed Laser Irradiation

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 268
Author(s):  
Jung Won Choi ◽  
Daseul Ham ◽  
Seonghyun Han ◽  
Do Young Noh ◽  
Hyon Chol Kang
Keyword(s):  
Contact Angle ◽  
Sapphire Substrate ◽  
Pulsed Laser ◽  
Contact Angles ◽  
Metal Thin Films ◽  
Liquid Drops ◽  
Wetting Behavior ◽  
Solid Substrates ◽  
Co Nanoparticles ◽  
Amorphous Al2o3

Liquid drops on deformable soft substrates exhibit quite complicated wetting behavior as compared to those on rigid solid substrates. We report on a soft wetting behavior of Co nanoparticles (NPs) on a sapphire substrate during pulsed laser-induced dewetting (PLID). Co NPs produced by PLID wetted the sapphire substrate with a contact angle near 70°, which is in contrast to typical dewetting behavior of metal thin films exhibiting contact angles greater than 90°. In addition, a nanoscale γ-Al2O3 wetting ridge about 15 nm in size and a thin amorphous Al2O3 interlayer were observed around and beneath the Co NP, respectively. The observed soft wetting behavior strongly indicates that the sapphire substrate became soft and deformable during PLID. Moreover, the soft wetting was augmented under PLID in air due to the formation of a CoO shell, resulting in a smaller contact angle near 30°.

scholarly journals Biomimetic Approach for the Elaboration of Highly Hydrophobic Surfaces: Study of the Links between Morphology and Wettability

Biomimetics ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 38
Author(s):  
Quentin Legrand ◽  
Stephane Benayoun ◽  
Stephane Valette
Keyword(s):  
Contact Angle ◽  
Ginkgo Biloba ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Textured Surfaces ◽  
Replication Process ◽  
Wetting Behavior ◽  
Static Contact ◽  
Biomimetic Approach ◽  
Highly Hydrophobic

This investigation of morphology-wetting links was performed using a biomimetic approach. Three natural leaves’ surfaces were studied: two bamboo varieties and Ginkgo Biloba. Multiscale surface topographies were analyzed by SEM observations, FFT, and Gaussian filtering. A PDMS replicating protocol of natural surfaces was proposed in order to study the purely morphological contribution to wetting. High static contact angles, close to 135∘, were measured on PDMS replicated surfaces. Compared to flat PDMS, the increase in static contact angle due to purely morphological contribution was around 20∘. Such an increase in contact angle was obtained despite loss of the nanometric scale during the replication process. Moreover, a significant decrease of the hysteresis contact angle was measured on PDMS replicas. The value of the contact angle hysteresis moved from 40∘ for flat PDMS to less than 10∘ for textured replicated surfaces. The wetting behavior of multiscale textured surfaces was then studied in the frame of the Wenzel and Cassie–Baxter models. Whereas the classical laws made it possible to describe the wetting behavior of the ginkgo biloba replications, a hierarchical model was developed to depict the wetting behavior of both bamboo species.

Surface Topography Induced Ultrahydrophobic Behavior: Effect of Three-Phase Contact Line Topology

2006 ◽  
Author(s):  
Neeharika Anantharaju ◽  
Mahesh Panchagnula ◽  
Wayne Kimsey ◽  
Sudhakar Neti ◽  
Svetlana Tatic-Lucic
Keyword(s):  
Contact Angle ◽  
Contact Line ◽  
Anomalous Behavior ◽  
Contact Angles ◽  
Wet Etching ◽  
Surface Geometry ◽  
Wetting Behavior ◽  
Void Fractions ◽  
Three Phase ◽  
Receding Contact

The wettability of silicon surface hydrophobized using silanization reagents was studied. The advancing and receding contact angles were measured with the captive needle approach. In this approach, a drop under study was held on the hydrophobized surface with a fine needle immersed in it. The asymptotic advancing and receding angles were obtained by incrementally increasing the volume added and removed, respectively, until no change in angles was observed. The values were compared with the previously published results. Further, the wetting behavior of water droplets on periodically structured hydrophobic surfaces was investigated. The surfaces were prepared with the wet etching process and contain posts and holes of different sizes and void fractions. The surface geometry brought up a scope to study the Wenzel (filling of surface grooves) and Cassie (non filling of the surface grooves) theories and effects of surface geometry and roughness on the contact angle. Experimental data point to an anomalous behavior where the data does not obey either Wenzel or Cassie type phenomenology. This behavior is explained by an understanding of the contact line topography. The effect of contact line topography on the contact angle was thus parametrically studied. It was also inferred that, the contact angle increased with the increase in void fraction. The observations may serve as guidelines in designing surfaces with the desired wetting behavior.

Macroscopic Wetting Behavior and a Method for Measuring Contact Angles

1990 ◽  
Vol 112 (3) ◽  
pp. 289-295 ◽  
Author(s):  
K. Katoh ◽  
H. Fujita ◽  
H. Sasaki
Keyword(s):  
Contact Angle ◽  
Solid Surface ◽  
Liquid Surface ◽  
Contact Angles ◽  
Critical Height ◽  
Solid Cone ◽  
Wetting Behavior ◽  
Conventional View ◽  
The Subject ◽  
Thermodynamic Instability

Macroscopic wetting behavior is investigated theoretically from a thermodynamic viewpoint. The axisymmetric liquid meniscus formed under a conical solid surface is chosen as the subject of the theoretical analysis. Using the meniscus configuration obtained by the Laplace equation, the total free energy of the system is calculated. In the case of the half vertical angle of the cone φ = 90 deg (horizontal plate), the system shows thermodynamic instability when the meniscus attaches to the solid surface at the contact angle. This result, unlike the conventional view, agrees well with the practical wetting behavior observed in this study. On the other hand, when 0 deg < φ < 90 deg, the system shows thermodynamic stability at the contact angle. However, when the solid cone is held at a position higher than the critical height from a stationary liquid surface, the system becomes unstable. It is possible to measure the contact angle easily using this unstable phenomenon.

scholarly journals Amphiphobic Nanostructured Coatings for Industrial Applications

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 787 ◽  
Author(s):  
Federico Veronesi ◽  
Giulio Boveri ◽  
Mariarosa Raimondo
Keyword(s):  
Surface Tension ◽  
Contact Angle ◽  
Photoelectron Spectroscopy ◽  
Contact Angle Hysteresis ◽  
Contact Angles ◽  
Friction Reduction ◽  
Hybrid Coatings ◽  
Wetting Behavior ◽  
Wide Range ◽  
Solid Liquid

The search for surfaces with non-wetting behavior towards water and low-surface tension liquids affects a wide range of industries. Surface wetting is regulated by morphological and chemical features interacting with liquid phases under different ambient conditions. Most of the approaches to the fabrication of liquid-repellent surfaces are inspired by living organisms and require the fabrication of hierarchically organized structures, coupled with low surface energy chemical composition. This paper deals with the design of amphiphobic metals (AM) and alloys by deposition of nano-oxides suspensions in alcoholic or aqueous media, coupled with perfluorinated compounds and optional infused lubricant liquids resulting in, respectively, solid–liquid–air and solid–liquid–liquid working interfaces. Nanostructured organic/inorganic hybrid coatings with contact angles against water above 170°, contact angle with n-hexadecane (surface tension γ = 27 mN/m at 20 °C) in the 140–150° range and contact angle hysteresis lower than 5° have been produced. A full characterization of surface chemistry has been undertaken by X-ray photoelectron spectroscopy (XPS) analyses, while field-emission scanning electron microscope (FE-SEM) observations allowed the estimation of coatings thicknesses (300–400 nm) and their morphological features. The durability of fabricated amphiphobic surfaces was also assessed with a wide range of tests that showed their remarkable resistance to chemically aggressive environments, mechanical stresses and ultraviolet (UV) radiation. Moreover, this work analyzes the behavior of amphiphobic surfaces in terms of anti-soiling, snow-repellent and friction-reduction properties—all originated from their non-wetting behavior. The achieved results make AM materials viable solutions to be applied in different sectors answering several and pressing technical needs.

WETTING OF ROUGH SURFACES

2004 ◽  
Vol 11 (01) ◽  
pp. 7-13 ◽  
Author(s):  
XINPING ZHANG ◽  
SIRONG YU ◽  
ZHENMING HE ◽  
YAOXIN MIAO
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Sessile Drop ◽  
Test Sample ◽  
Contact Angles ◽  
Sessile Drop Method ◽  
Equilibrium Contact Angle ◽  
Roughness Surface ◽  
Solid Substrates ◽  
Effect Of Surface

This paper focuses on effects of roughness on wettability. According to Wenzel's equation, the transition of theoretical wetting contact angles is 90°, whereas many experimental results have indicated that such a transition takes place at contact angles smaller than 90°. A new model of wetting on roughness surface is established in this paper. The model indicates that the influencing factors of wetting on roughness surface include not only equilibrium contact angle θ0 and surface roughness, but also the system of liquids and solid substrates. There is a corresponding transition angle for every surface roughness, and the transition angle is lower than 90°. Surface roughness is propitious to improve the contact angle only when θ0 is lower than the transition angle. The effect of surface roughness on the contact angle increases with the increase of rE. To engineer the surface with different roughnesses, a Ti test sample is polished with sandpaper with abrasive number 350, 500, 1000 and 2000; the contact angles of water on Ti are measured by the sessile drop method. The results of the theoretical analysis agree with experimental ones.

scholarly journals Effect of Direct Current on Solid-Liquid Interfacial Tension and Wetting Behavior of Ga–In–Sn Alloy Melt on Cu Substrate

2018 ◽  
Vol 2018 ◽  
pp. 1-7
Author(s):  
Limin Zhang ◽  
Ning Li ◽  
Hui Xing ◽  
Rong Zhang ◽  
Kaikai Song
Keyword(s):  
Contact Angle ◽  
Interfacial Tension ◽  
Direct Current ◽  
Sessile Drop ◽  
Contact Angles ◽  
Current Intensity ◽  
Solute Diffusion ◽  
Wetting Behavior ◽  
Cu Substrate ◽  
Solid Liquid

The effect of direct current (DC) on the wetting behavior of Cu substrate by liquid Ga–25In–13Sn alloy at room temperature is investigated using a sessile drop method. It is found that there is a critical value for current intensity, below which the decrease of contact angle with increasing current intensity is approximately linear and above which contact angle tends to a stable value from drop shape. Current polarity is a negligible factor in the observed trend. Additionally, the observed change in contact angles is translated into the corresponding change in solid-liquid interfacial tension using the equation of state for liquid interfacial tensions. The solid-liquid interfacial tension decreases under DC. DC-induced promotion of solute diffusion coefficient is likely to play an important role in determining the wettability and solid-liquid interfacial tension under DC.

WETTING BEHAVIOR OF Al–Mg ALLOYS ON CARBON FIBER FABRIC

2013 ◽  
Vol 20 (03n04) ◽  
pp. 1350036 ◽  
Author(s):  
WANG XU ◽  
WANG CHENCHONG ◽  
CHEN GUOQIN ◽  
YANG WENSHU ◽  
ZHANG ZHICHAO
Keyword(s):  
Contact Angle ◽  
Carbon Fiber ◽  
Sessile Drop ◽  
Contact Angles ◽  
Mg Alloys ◽  
Holding Time ◽  
Dominant Effect ◽  
Wetting Behavior ◽  
Fiber Fabric ◽  
Al Mg Alloys

In present work, the wetting behavior of carbon fiber and Al – Mg alloys (up to 17 wt.%) from 700°C to 1000°C was investigated by sessile drop method. Below 900°C, the contact angles decreased slightly with increase of temperature regardless of Mg amount. However, the contact angles decreased sharply at elevated temperature (above 900°C). Moreover, below 900°C, the contact angles decreased slightly with holding time, and significant decrease of contact angle with increase of holding time was found above 1000°C. All contact angle-holding time curves at 1000°C demonstrated three kinetic stages. It is observed that the contact angles decreased with Mg amount regardless of wetting temperature. The addition of Mg element will inhabit the nucleation and growth of Al 4 C 3 phase, which is unfavorable to the wetting behavior. However, the addition of Mg element will also decrease the surface energy, which demonstrates dominant effect and leads to the decrease of contact angles.

scholarly journals Aluminum Melt Filtration with Carbon Bonded Alumina Filters

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 3962
Author(s):  
Claudia Voigt ◽  
Jana Hubálková ◽  
Tilo Zienert ◽  
Beate Fankhänel ◽  
Michael Stelter ◽  
...  
Keyword(s):  
Contact Angle ◽  
Sessile Drop ◽  
Contact Angles ◽  
Apparent Contact Angle ◽  
Drop Test ◽  
Aluminum Melt ◽  
Wetting Behavior ◽  
Purification Unit ◽  
Conventional Test ◽  
Porous Disc

The wetting behavior was measured for Al2O3-C in contact with AlSi7Mg with a conventional sessile drop test (vacuum, 950 °C and 180 min) and a sessile drop test with a capillary purification unit (vacuum, 730 °C and 30 min). The conventional test yielded contact angles of around 92°, whereas the sessile drop measurement with capillary purification showed a strongly non-wetting behavior with a determined apparent contact angle of the rolling drop of 157°. Filtration tests, which were repeated twice, showed that the Al2O3-C filter possessed a better filtration behavior than the Al2O3 reference filter. For both filtration trials, the PoDFA (porous disc filtration analysis) index of the Al2O3-C filter sample was equal to half of the PoDFA index of the Al2O3 reference filter sample, indicating a significantly improved filtration performance when using Al2O3-C filter. Notable is the observation of a newly formed layer between the aluminum and the Al2O3-C coating. The layer possessed a thickness between 10 µm up to 50 µm and consisted of Al, C, and O, however, with different ratios than the original Al2O3-C coating. Thermodynamic calculations based on parameters of the wetting and filtration trials underline the possible formation of an Al4O4C-layer.

scholarly journals Time-Dependent Anisotropic Wetting Behavior of Deterministic Structures of Different Strut Widths on Ti6Al4V

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 938 ◽  
Author(s):  
Georg Schnell ◽  
Christopher Jagow ◽  
Armin Springer ◽  
Marcus Frank ◽  
Hermann Seitz
Keyword(s):  
Contact Angle ◽  
Sessile Drop ◽  
Ambient Air ◽  
Laser Wavelength ◽  
Contact Angles ◽  
Femtosecond Laser Irradiation ◽  
Ultrapure Water ◽  
Wetting Behavior ◽  
Maximum Contact ◽  
Deterministic Structures

This study investigated the wetting behavior of Ti6Al4V surfaces that were groove-structured by means of femtosecond laser irradiation. The material was treated under ambient air conditions by use of a laser wavelength of 1030 nm and a pulse duration of 300 fs. Highly accurate structures with a gap width of 20 µm, a gap depth of 10 µm, and varying strut widths (1–300 µm) were generated and the contact angles in parallel and perpendicular direction were determined using sessile drop method with ultrapure water 1, 8, and 15 days after irradiation. All deterministic surfaces exhibited a pronounced contact angle change over time. The structures showed a strong anisotropic wetting behavior with a maximum contact angle aspect ratio of 2.47 at a strut width of 40 µm and a maximum difference between the parallel and perpendicular contact angle of 47.9° after 1 day.

Sign in / Sign up

Export Citation Format

Share Document