scholarly journals A Methodology Towards Mechanical Properties Optimization of Three-Component Polymers by the Gradual Variation of Feed Composition in Semi-Continuous Emulsion-Free Radical Polymerization

Polymers ◽  
2019 ◽  
Vol 11 (12) ◽  
pp. 2125
Author(s):  
Francisco J. Rivera-Gálvez ◽  
Luis J. González-Ortiz ◽  
Miguel A. López-Manchado ◽  
María E. Hernández-Hernández ◽  
Carlos F. Jasso-Gastinel
Keyword(s):  
Free Radical ◽  
Energy Dissipation ◽  
Polymeric Materials ◽  
Batch Process ◽  
Mechanical Analysis ◽  
Synthesis Methods ◽  
Scanning Calorimetry ◽  
Feed Composition ◽  
Ultimate Deformation ◽  
Energy Dissipation Capacity

In this work, a new methodology for the synthesis of three-component polymers (TCPs) was developed using a seeded, semi-continuous free-radical emulsion polymerization towards the optimization of the moduli–ultimate deformation performance and energy dissipation capacity for a styrene (S), n-butyl acrylate (BA), and 4-vinylbenzyl chloride (VBC) system. The three components were sequentially fed in pairs, varying feed composition along the conversion using S as the common monomer. To prepare a reference material, an industrial method was utilized with those monomers, using an equivalent global composition in a two-stage batch process (TS). Nanophase formation in the particles was observed by transmission electron microscopy (TEM), while the separation of the phases in the solid samples was observed by atomic force microscopy (AFM). The changes in glass transition temperature were determined by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The latter was primarily used to compare mechanodynamic properties as a function of temperature for the two synthesis methods used. Thus, the higher toughness of the forced composition three-component polymeric materials was evaluated by means of their energy dissipation capacity, toughness, and stress–strain measurements at several temperatures.

Application of dynamic mechanical analysis techniques to bismuth telluride based thermoelectric materials

e-Polymers ◽  
2004 ◽  
Vol 4 (1) ◽  
Author(s):  
Witold Brostow ◽  
Kevin P. Menard ◽  
John B. White
Keyword(s):  
Dynamic Mechanical Analysis ◽  
Bismuth Telluride ◽  
Polymeric Materials ◽  
Mechanical Analysis ◽  
Thermomechanical Properties ◽  
Thermal Transitions ◽  
Scanning Calorimetry ◽  
Dynamic Mechanical ◽  
Tan Δ ◽  
Te Material

Abstract Dynamic mechanical analysis (DMA) techniques are commonly applied to characterize polymer-based materials - but little if at all to characterize semiconductor thermoelectric (TE) materials. TE materials may be coupled with polymeric materials in advanced thermoelectric devices, and the knowledge of TE material properties will be useful in the choice of materials for future applications. We have obtained DMA results for both n-type and p-type bismuth telluride based TE materials. We find that tan δ values, indicative of viscoelastic energy dissipation modes, approach the values for glassy or semi-crystalline polymers, and are larger by more than a whole order of magnitude than the tan δ of structural metals. DMA thermal scans show clear hysteresis-type effects and a correlation with differential scanning calorimetry thermal transitions. DMA properties as a function of frequency are briefly discussed. Our results show that DMA techniques are useful in the evaluation of thermophysical and thermomechanical properties of these TE materials and of assembled coolers. The viscoelastic effects we report may provide a damping mechanism for severe stresses inherent to service conditions of the TE coolers.

scholarly journals Sulfur/Organic Copolymers as Curing Agents for Rubber

Polymers ◽  
2018 ◽  
Vol 10 (8) ◽  
pp. 870 ◽  
Author(s):  
Jakub Wręczycki ◽  
Dariusz Bieliński ◽  
Rafał Anyszka
Keyword(s):  
Mechanical Properties ◽  
Crosslink Density ◽  
Elemental Sulfur ◽  
Freezing Point ◽  
Petroleum Industry ◽  
Polymeric Materials ◽  
Mechanical Analysis ◽  
Radical Copolymerization ◽  
Scanning Calorimetry ◽  
Free Radical Copolymerization

It is widely acknowledged that waste sulfur generated from the petroleum industry creates huge storage and ecological problems. Therefore, the various methods of utilization are becoming increasingly attractive research topics worldwide. The thermal ability of elemental sulfur to homolytic cleavage of S8 rings enables its free radical copolymerization with unsaturated organic species and the obtaining of chemically stable polymeric materials. Here we report a novel possibility to use sulfur/organic copolymers obtained via “inverse vulcanization” as curatives for rubber. For this purpose, several various sulfur/organic copolymers were synthesized and analyzed from the point of view of their performance as rubber crosslinking agents. Solvent extraction was used to purify sulfur/organic copolymers from unreacted (elemental) sulfur. Thermal properties of the prepared copolymers were characterized by thermogravimetric analysis and differential scanning calorimetry (TGA–DSC). Crosslink density and structure of cured elastomers was studied by equilibrium swelling, thiol-amine analysis and freezing point depression. Mechanical properties of the vulcanizates were determined under static and dynamic conditions (DMA—dynamic mechanical analysis). It is proved that the utilization of sulfur/organic copolymers as curatives enables an effective crosslinking process of rubbers. Taking into account the results of a crosslink density analysis and mechanical properties of the vulcanizates cured with purified copolymers, it is evident that relatively long copolymer macromolecules are also involved in the formation of chemical bonds between unsaturated rubber macromolecules.

Mechanical Properties of Laser Cut Poly(L-Lactide) Micro-Specimens: Implications for Stent Design, Manufacture, and Sterilization

2005 ◽  
Vol 127 (1) ◽  
pp. 25-31 ◽  
Author(s):  
Niels Grabow ◽  
Martin Schlun ◽  
Katrin Sternberg ◽  
Nico Hakansson ◽  
Sven Kramer ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Material Selection ◽  
Polymeric Materials ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Machining Process ◽  
Scanning Calorimetry ◽  
Vascular Stents ◽  
Before And After ◽  
Solution Cast

Background: The development of endoluminal stents from polymeric materials requires an understanding of the basic mechanical properties of the polymer and the effects of manufacturing and sterilization on those properties. Methods: Pure poly(L-lactide) (PLLA) and PLLA containing varying amounts of triethylcitrate (TEC) as a plasticizer (5-10-15%) were studied. The specimens were solution-cast and CO2 laser-cut. Specimen dimensions were adapted to the strut size of polymeric vascular stents. The properties of the PLLA micro-specimens were assessed before and after sterilization (EtO cold gas, H2O2-plasma, beta- and gamma-irradiation). Tensile tests, and creep and recovery tests were carried out at 37°C. Additionally the thermal and thermo-mechanical characteristics were investigated using dynamic-mechanical analysis (DMA) and differential scanning calorimetry (DSC). Results: The results showed the dramatic influence of the plasticizer content and sterilization procedure on the mechanical properties of the material. Laser cutting had a lesser effect. Hence the effects of processing and sterilization must not be overlooked in the material selection and design phases of the development process leading to clinical use. Altogether, the results of these studies provide a clearer understanding of the complex interaction between the laser machining process and terminal sterilization on the primary mechanical properties of PLLA and PLLA plasticized with TEC.

Light-cured dental composites characterization by Electron Microscopy

1990 ◽  
Vol 48 (4) ◽  
pp. 428-429
Author(s):  
B. M. Culbertson ◽  
M. L. Devinev ◽  
E. C. Kao
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Service Performance ◽  
Dental Composite ◽  
Dental Composites ◽  
Neat Resin ◽  
Scanning Calorimetry ◽  
Research Meeting ◽  
Formulation Variables

The service performance of current dental composite materials, such as anterior and posterior restoratives and/or veneer cements, needs to be improved. As part of a comprehensive effort to find ways to improve such materials, we have launched a broad spectrum study of the physicochemical and mechanical properties of photopolymerizable or visible light cured (VLC) dental composites. The commercially available VLC materials being studied are shown in Table 1. A generic or neat resin VLC system is also being characterized by SEM and TEM, to more fully understand formulation variables and their effects on properties.At a recent dental research meeting, we reported on the differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) characterization of the materials in Table 1. It was shown by DSC and DMA that the materials are substantially undercured by commonly used VLC techniques. Post curing in an oral cavity or a dry environment at 37 to 50°C for 7 or more hours substantially enhances the cure of the materials.

Star-shaped arylacetylene resins derived from silicon

2020 ◽  
Vol 40 (8) ◽  
pp. 676-684
Author(s):  
Niping Dai ◽  
Junkun Tang ◽  
Manping Ma ◽  
Xiaotian Liu ◽  
Chuan Li ◽  
...  
Keyword(s):  
High Performance ◽  
Room Temperature ◽  
Mechanical Test ◽  
Flexural Modulus ◽  
Mechanical Analysis ◽  
Reinforced Composites ◽  
Scanning Calorimetry ◽  
Chemical Structures ◽  
Structures And Properties ◽  
High Performance Resin

AbstractStar-shaped arylacetylene resins, tris(3-ethynyl-phenylethynyl)methylsilane, tris(3-ethynyl-phenylethynyl) phenylsilane, and tris (3-ethynyl-phenylethynyl) silane (TEPHS), were synthesized through Grignard reaction between 1,3-diethynylbenzene and three types of trichlorinated silanes. The chemical structures and properties of the resins were characterized by means of nuclear magnetic resonance, fourier-transform infrared spectroscopy, Haake torque rheomoter, differential scanning calorimetry, dynamic mechanical analysis, mechanical test, and thermogravimetric analysis. The results show that the melt viscosity at 120 °C is lower than 150 mPa⋅s, and the processing windows are as wide as 60 °C for the resins. The resins cure at the temperature as low as 150 °C. The good processabilities make the resins to be suitable for resin transfer molding. The cured resins exhibit high flexural modulus and excellent heat-resistance. The flexural modulus of the cured TEPHS at room temperature arrives at as high as 10.9 GPa. Its temperature of 5% weight loss (Td5) is up to 697 °C in nitrogen. The resins show the potential for application in fiber-reinforced composites as high-performance resin in the field of aviation and aerospace.

scholarly journals Proof-of-Concept of Detection of Counterfeit Medicine through Polymeric Materials Analysis of Plastics Packaging

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2185
Author(s):  
Mohammad Salim ◽  
Riyanto Teguh Widodo ◽  
Mohamed Ibrahim Noordin
Keyword(s):  
Polymeric Materials ◽  
Proof Of Concept ◽  
Scanning Calorimetry ◽  
Counterfeit Drug ◽  
Drug Products ◽  
Counterfeit Medicines ◽  
Counterfeit Medicine ◽  
Counterfeit Pharmaceuticals ◽  
Purge Gas ◽  
Sample Set

The detection of counterfeit pharmaceuticals is always a major challenge, but the early detection of counterfeit medicine in a country will reduce the fatal risk among consumers. Technically, fast laboratory testing is vital to develop an effective surveillance and monitoring system of counterfeit medicines. This study proposed the combination of Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) and Differential Scanning Calorimetry (DSC) for the quick detection of counterfeit medicines, through the polymer analysis of blister packaging materials. A sample set containing three sets of original and counterfeit medicine was analyzed using ATR-FTIR and DSC, while the spectra from ATR-FTIR were employed as a fingerprint for the polymer characterization. Intending to analyze the polymeric material of each sample, DSC was set at a heating rate of 10 °C min−l and within a temperature range of 0- 400 °C, with nitrogen as a purge gas at a flow rate of 20 ml min−an. The ATR-FTIR spectra revealed the chemical characteristics of the plastic packaging of fake and original medicines. Further analysis of the counterfeit medicine’s packaging with DSC exhibited a distinct difference from the original due to the composition of polymers in the packaging material used. Overall, this study confirmed that the rapid analysis of polymeric materials through ATR-FTIR and comparing DSC thermograms of the plastic in their packaging effectively distinguished counterfeit drug products.

scholarly journals Relationship between the Stereocomplex Crystallization Behavior and Mechanical Properties of PLLA/PDLA Blends

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1851
Author(s):  
Hye-Seon Park ◽  
Chang-Kook Hong
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Crystallization Behavior ◽  
Mechanical Analysis ◽  
X Ray Diffraction ◽  
Nucleation Agent ◽  
Scanning Calorimetry ◽  
Nucleation Sites ◽  
Wide Range ◽  
Degree Of Crystallization

Poly (l-lactic acid) (PLLA) is a promising biomedical polymer material with a wide range of applications. The diverse enantiomeric forms of PLLA provide great opportunities for thermal and mechanical enhancement through stereocomplex formation. The addition of poly (d-lactic acid) (PDLA) as a nucleation agent and the formation of stereocomplex crystallization (SC) have been proven to be an effective method to improve the crystallization and mechanical properties of the PLLA. In this study, PLLA was blended with different amounts of PDLA through a melt blending process and their properties were calculated. The effect of the PDLA on the crystallization behavior, thermal, and mechanical properties of PLLA were investigated systematically by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), polarized optical microscopy (POM), dynamic mechanical analysis (DMA), and tensile test. Based on our findings, SC formed easily when PDLA content was increased, and acts as nucleation sites. Both SC and homo crystals (HC) were observed in the PLLA/PDLA blends. As the content of PDLA increased, the degree of crystallization increased, and the mechanical strength also increased.

scholarly journals Study on Structure, Thermal Behavior, and Viscoelastic Properties of Nanodiamond-Reinforced Poly (vinyl alcohol) Nanocomposites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1426
Author(s):  
Tomáš Remiš ◽  
Petr Bělský ◽  
Tomáš Kovářík ◽  
Jaroslav Kadlec ◽  
Mina Ghafouri Azar ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Analysis ◽  
Single Step ◽  
Poly Vinyl Alcohol ◽  
Scanning Calorimetry ◽  
X Ray Scattering ◽  
Transmission Electron ◽  
Primary Particles ◽  
Solution Casting Method ◽  
Average Size

In this work, advanced polymer nanocomposites comprising of polyvinyl alcohol (PVA) and nanodiamonds (NDs) were developed using a single-step solution-casting method. The properties of the prepared PVA/NDs nanocomposites were investigated using Raman spectroscopy, small- and wide-angle X-ray scattering (SAXS/WAXS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). It was revealed that the tensile strength improved dramatically with increasing ND content in the PVA matrix, suggesting a strong interaction between the NDs and the PVA. SEM, TEM, and SAXS showed that NDs were present in the form of agglomerates with an average size of ~60 nm with primary particles of diameter ~5 nm. These results showed that NDs could act as a good nanofiller for PVA in terms of improving its stability and mechanical properties.

scholarly journals Experimental and Numerical Analysis of the Mechanical Properties of a Pretreated Shape Memory Alloy Wire in a Self-Centering Steel Brace

Processes ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 80
Author(s):  
Bo Zhang ◽  
Sizhi Zeng ◽  
Fenghua Tang ◽  
Shujun Hu ◽  
Qiang Zhou ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Energy Dissipation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Loading Rate ◽  
Effective Elastic Modulus ◽  
Maximum Energy ◽  
Numerical Results ◽  
Energy Dissipation Capacity

As a stimulus-sensitive material, the difference in composition, fabrication process, and influencing factors will have a great effect on the mechanical properties of a superelastic Ni-Ti shape memory alloy (SMA) wire, so the seismic performance of the self-centering steel brace with SMA wires may not be accurately obtained. In this paper, the cyclic tensile tests of a kind of SMA wire with a 1 mm diameter and special element composition were tested under multi-working conditions, which were pretreated by first tensioning to the 0.06 strain amplitude for 40 cycles, so the mechanical properties of the pretreated SMA wires can be simulated in detail. The accuracy of the numerical results with the improved model of Graesser’s theory was verified by a comparison to the experimental results. The experimental results show that the number of cycles has no significant effect on the mechanical properties of SMA wires after a certain number of cyclic tensile training. With the loading rate increasing, the pinch effect of the hysteresis curves will be enlarged, while the effective elastic modulus and slope of the transformation stresses in the process of loading and unloading are also increased, and the maximum energy dissipation capacity of the SMA wires appears at a loading rate of 0.675 mm/s. Moreover, with the initial strain increasing, the slope of the transformation stresses in the process of loading is increased, while the effective elastic modulus and slope of the transformation stresses in the process of unloading are decreased, and the maximum energy dissipation capacity appears at the initial strain of 0.0075. In addition, a good agreement between the test and numerical results is obtained by comparing with the hysteresis curves and energy dissipation values, so the numerical model is useful to predict the stress–strain relations at different stages. The test and numerical results will also provide a basis for the design of corresponding self-centering steel dampers.

Sign in / Sign up

Export Citation Format

Share Document